Items where Subject is "TJ Mechanical engineering and machinery"

Group by: Creators | Item Type
Jump to: | , | . | @ | A | B | C | D | E | F | G | H | I | J | K | L | M | N | O | P | Q | R | S | T | U | V | W | X | Y | Z
Number of items at this level: 2327.

AMARPALL SINGH, AJIT SINGH (2020) THE EFFECT OF WEIGHT PERCENTAGES OF CARBONYL IRON PARTICLES (CIP) ON THE PHYSICOCHEMICAL CHARACTERISTICS OF EPOXIDIZED NATURAL RUBBER-50 (ENR-50) BASED MAGNETORHEOLOGICAL ELASTOMERS (MRE). [Final Year Project] (Submitted)

Abd Rashid @ Abd Rasip, Mohd Hanafi (2009) Design Calculation ofthe Upgraded Equipments for Residue Plant Under Different Operating Capacity. [Final Year Project] (Unpublished)

Abdul Hakim, Muhammad Effirdaus (2004) Investigation of Multi-cylinder Diesel Engine Performance and Emission Using Bio-diesel Fuel. [Final Year Project] (Unpublished)

Abdul Jalil, Muhammad Bukhari (2008) Freezing Point Depression Method for Hydrate Monitoring. [Final Year Project] (Unpublished)

Abdullah, Mohd Aimran (2011) STRESS ANALYSIS ON MECHANICAL SEAL (SINGLE SEAL). [Final Year Project] (Unpublished)

Abdullah Saloji, Nasrullah (2020) Study on physicochemical properties of Magnetorheological Elastomer Featuring Naphthenic Oil as Additive. [Final Year Project] (Submitted)

Ahmad, Safinah (2012) Modal Analysis of Rotary Piston Blower. [Final Year Project] (Unpublished)

Ahmad, Zarizambri (2008) Design and Analysis of a Pedal Box System for a small Race-car. [Final Year Project] (Unpublished)

Ahmad Supian, Azlia (2011) SEA-BED LOGGING MODELING USING COMSOL MULTIPHYSICS SOFTWARE: EFFECT OF DISPERSED CLAY AND BRINE SALINITY TO ELECTROMAGNETIC WAVE. [Final Year Project] (Unpublished)

Ahmed Elmahdi, Anas Elrayah (2013) Study of Performance Enhancement of a Building in Tropical Climate. [Final Year Project] (Unpublished)

Ali, Abd Azim Aizat Bin (2009) Application of Corrosion Prediction Software to Optimize Material Selection in Offshore Pipelines and Tubing. [Final Year Project] (Unpublished)

Amir, Nadiah (2011) STUDY INTO THE EFFECT OF CUTTING SPEED ON THE SURFACE ROUGHNESS, ROUNDNESS, TOOL WEAR AND CHIP FORMATION DURING LATHE CUTTING OPERATION. [Final Year Project] (Unpublished)

Anis, Azarudeen (2011) Design of Two-Stages Charging of Sensible Thermal Energy Storage. [Final Year Project] (Unpublished)

Arif, Muharnad Fatikul (2008) Mechanical and Water Absorption Properties of Oil Palm Empty Fruit Bunch-High Density Polyethylene Composites. Masters thesis, Universiti Teknologi Petronas.

Arizam, Muhammad Hafizuddin Adha (2013) FINITE ELEMENT ANALYSIS OF RESIDUAL STRESSES IN BUTT WELDING JOINT OF ASTM A36 PLATE AND ITS EFFECT ON FATIGUE CRACK GROWTH. [Final Year Project] (Unpublished)

Ayob, Adzlan Bin (2009) Prediction of CO2 Corrosion for Welded Joints. [Final Year Project] (Unpublished)

Aziz, Muhammad Farhan (2013) Minimizing Preventive Maintenance Costs of An Equipment in Oil and Gas (O&G) Industry. [Final Year Project] (Unpublished)

DERAMAN, RAFFLELLA (2013) A Study on Blade Performance of Transverse Axis Wind Turbine Mounted on a Rooftop. [Final Year Project] (Unpublished)

Dawam, Mohamad Di-Fazley (2004) Modeling of Production of Injected Plastic Product Using Forecasting, Aggregate Planning and Linear Programming Approach. [Final Year Project] (Unpublished)

Fatahal Karim, Mohd Salman (2004) INVESTIGATION OF MINI STEAM POWER PLANT PERFORMANCE AND EMISSIONS. [Final Year Project] (Unpublished)

Hamdan, Muhamad Faris (2013) CFD Modelling of Supersonic Wet Gas Separator. [Final Year Project] (Unpublished)

IBRAHIM ABDALLAH, MUNZIR AHME (2008) ANALYSIS OF PRESSURE DROP AND HEAT TRANSFER OF ANNULAR DEPOSITION TEST UNIT. Masters thesis, Universiti Teknologi Petronas.

Ibrahim, Muhammad Azwan (2015) Correlations between microstructure, nitrogen concentration and micro hardness of nitrided Ferritic Stainless Steel. [Final Year Project] (Unpublished)

Isa, Amirullah Bin (2009) EFFECTS OF AERODYNAMIC CHANGES FOR A CAR CAUSED BY ANOTHER IN ITS PROXIMITY: NUMERICAL STUDY. [Final Year Project] (Unpublished)

Ishak, Siti Nadiah (2011) Spectrum Analysis of Linear Time Invariant Gyroscopic System. [Final Year Project] (Unpublished)

Ismail, 'Izzuddin (2011) Value Analysis for Brake Disc Materials- Case of cast iron to composite. [Final Year Project] (Unpublished)

Ismail, Mohamad Rizal (2004) Study ofVarious Insulation Materials onthe performance of Non-Convecting Solar Pond in Malaysia. [Final Year Project] (Unpublished)

Ismail, Mohd Shahrul Ezwan (2013) Corrosion Behavior of Intumescent Coated Steel In Seawater Environment. [Final Year Project] (Unpublished)

Ismail, Muhammad (2004) Study on Performance and Emission Characteristics of Diesel Engines Using Ethanol-Blended Diesel Fuel. [Final Year Project] (Unpublished)

Ismail, Muhammad Iskandar (2013) The Effects of Surfactant on Combustion Characteristics of Emulsified Diesel Fuel. [Final Year Project] (Unpublished)

LEE , PETER CHEE HONG (2008) DEVELOPING MULTI-DEGREES OF FREEDOM OF DEXTEROUS HUMANOID ROBOTIC HAND. [Final Year Project] (Unpublished)

MUHAMMAD NUR AZLEE STANLEY, MUHAMMAD NUR AFIF DANIAL (2020) COMPUTATIONAL FLUID DYNAMICS (CFD) SIMULATION OF BYPASS FRACTION FOR BYPASS PIG IN MULTIPHASE FLOW. [Final Year Project] (Submitted)

Makhtar, Aini Munirah bt (2009) Investigation of Stress Intensity Factor at Compact Tension Specimen. [Final Year Project] (Unpublished)

Mazalan, Siti Fatimah (2008) Comparative Study of Different C02 Injection Modes for Baronia RV2 Reservoir. [Final Year Project] (Unpublished)

Md Aris, Mohd Farid (2004) Re-designing of Solar Collector Using Newly Developed Insulations and Materials. [Final Year Project] (Unpublished)

Md Saru, Mohd Syahrul Azman Bin (2009) A Study of Stress Distribution on Centrifugal Compressor Impeller Using Finite Element Analysis. [Final Year Project] (Unpublished)

Md Yazid, Mohd Bariq (2010) Cylinder Deactivation ofPERODUA Viva UJL Engine for Better Fuel Consumption. [Final Year Project] (Unpublished)

Mohamad Redzuan, Intan Fazreenna (2020) Predicting Tensile Properties of Lalang Grass Fiber (LGF) Reinforced Polypropylene (PP) using Mathematical Modelling. [Final Year Project] (Submitted)

Mohd Ali, Ahmad Fadhil Hafiz (2008) The Enhancement of Micro Grinding Process by Using NdFeB to Seize Material Dust. [Final Year Project] (Unpublished)

Mohd Khalid, Muhammad Azrai (2020) GREEN CORROSION INHIBITOR ( THYME OIL) LOADED HNT FOR CORROSION PROTECTION OF CARBON STEEL. [Final Year Project] (Submitted)

Mohd Yusof, Mohd Shah Rizal (2008) Engine Performance and Exhaust Emission Characteristics of Fuel Oil-Diesel Fuel Mixture in a Single Cylinder Engine. [Final Year Project] (Unpublished)

Mohd Zolkafly, Muhammad Ariff Zaky (2013) Reverse Engineering of PDC Drill Bit. [Final Year Project] (Unpublished)

Mohd Zulkepli, Muhamad Aarif Billah (2013) Mathematical Modelling to Predict Nitrided Layer Thickness of Low Temperature Gas and Plasma Nitriding of AISI 316 L Stainless Steel (Austenitic). [Final Year Project] (Unpublished)

Mohiuddin, Zeeshan (2007) Study on potentials of Light Oil Air Injection (LOAI) in Malaysia Oil Fields. Masters thesis, Universiti Teknologi PETRONAS.

Muharnad, Dzulkarnain (2008) RE-ENGINEERING OF THE AIR INTAKE MANIFOLD FOR UTP FORMULA CAR. [Final Year Project] (Unpublished)

Mustadza, Ameirul Azraie Bin (2009) CO2 Corrosion Study of Carbon Steel in Natural and Induced Film Forming Environment. [Final Year Project] (Unpublished)

Nasron, Noorul Ameen Bin (2009) Finite Element Analysis of Unstringed Squash Racket Frame to Improve its Impact Strength. [Final Year Project] (Unpublished)

Ndong , Luis-Casiano Mikue (2008) Study on Pumping System Design for Water Injection. [Final Year Project] (Unpublished)

Osman, Nazrulhisham (2003) Software Development for Calculations of Voidage Replacement Ratio (VRR). [Final Year Project] (Unpublished)

Ping, Sharon Lee Lai (2013) Elementary process identification of solar carbon dioxide (CO2) fueling. [Final Year Project] (Unpublished)

RONG, LOO KAI (2017) Aerodynamic Characteristics of Gas Engine Compressor Under Different Surface Roughness Conditions. [Final Year Project]

Ramli, Mohd Razman (2004) To Develop a Knowledge-Based System for Parallel Machine Operations Scheduling. [Final Year Project] (Unpublished)

Ramli, Mohd Safwan Izzudin (2012) Line Modeling of C02 Corrosion of Offshore Pipeline. [Final Year Project] (Unpublished)

Ramli, Mohd Syahmi (2008) Experimental Assessment on Corrosion under Insulation (CUI). [Final Year Project] (Unpublished)

Razuki, Muhamad Afham (2020) Hydroxyapatite and Titania (HA-TiO2) powder mixed EDM for surface modification. [Final Year Project] (Submitted)

Ridzwan, Haszamail Ridzeli (2004) Structural Design and Styling of Composite External Body for Hybrid Electric Vehicle. [Final Year Project] (Unpublished)

Rusdi, Muhammad Aizuddin Bin (2009) Development of a Particulates Filtration System for Biomass Gas of Oil-Palm Fronds. [Final Year Project] (Unpublished)

Rusli, Nurul Masnem Ahza (2008) Design of Table with Adjustable Height. [Final Year Project] (Unpublished)

SUBRAMANIAM, SHALINI (2011) Corrosion Study of Nitrided X-52 Carbon Steel in C02 Environment. [Final Year Project] (Unpublished)

SURESH KUMAR, SUBHALAKSHMI (2021) DEVELOPMENT OF SMART ANTI-CORROSION COATINGS WITH METAL ION END CAPPED NANOCONTAINER LOADED WITH SINGLE AND DUO GREEN CORROSION INHIBITORS. Masters thesis, Universiti Teknologi PETRONAS.

Salleh, Syahril (2004) Development And Improvement Of Subsonic Wind Tunnel In Universiti Teknologi Petronas (Air Flow Quality Testing). [Final Year Project] (Unpublished)

Sudin, Mohd Nor Azlan (2010) Study on Effect of Nanosilica Sand Addition on Physicaland Mechanical Properties of Thermoplastic. [Final Year Project] (Unpublished)

VIJAYAKUMAR, THESIKAN (2017) TORSIONAL CONTROL OF STICK-SLIP OSCILLATIONS IN DRILL-STRING SYSTEM. [Final Year Project] (Unpublished)

VIN, LYE KEL (2017) PNEUMATIC SYSTEM OPERATED BY COMPRESSED AIR (C.A.E): AIR-POWERED VEHICLE. [Final Year Project]

Xin Wei, Yeap (2017) Gas Turbine Health Prognostics Using Artificial Neural Network. [Final Year Project] (Submitted)

Y ahaya, Mohd Roziee (2008) Effects of Particle Size on Mechanical Properties of Oil Palm Fruit Bunch Composites. [Final Year Project] (Unpublished)

Yaccob, Mohd Syazwan Akmal Bin (2009) Experimental Study on Strength of Friction Stir Spot Welding (FSSW). [Final Year Project] (Unpublished)

ZULAZNI, MUHAMMAD ASYRAF (2017) PART LOAD PERFORMANCE ANALYSIS OF ELECTRIC CHILLER AND STEAM ABSORPTION CHILLER AT DISTRICT COOLING PLANT. [Final Year Project]

ZULKIFLI, MOHD AMRI AZRI (2013) Investigation on Sensitization of Nitrided AISI 316L Austenitic Stainless Steel at Intermediate Temperature. [Final Year Project] (Unpublished)

Zahir, Muhammad Radzi (2005) Vehicle Crash Avoidance Modelling and Simulation Using Artificial Neural Network Approach. [Final Year Project] (Unpublished)

Zulkifli, Siti Nadiah (2013) Cornering Stability Analysis of Double Decker Bus at KM15 of Cameroon Highlands – Simpang Pulai Road. [Final Year Project] (Unpublished)

,

,, MUHAMMAD ASLAM (2016) POWDER INJECTION MOLDING OF MODIFIED 3I6L STAINLESS STEEL FOR DENTAL IMPLANT APPLICATION. PhD. thesis, Universiti Teknologi PETRONAS.

,, HAMMAD AZIZ (2014) DEVELOPMENT OF INORGANIC NANO FILLER REINFORCED INTUMESCENT FIRE RETARDANT COATING FOR STRUCTURAL APPLICATIONS. Masters thesis, Universiti Teknologi PETRONAS.

,, MUHAMADYUNUS (2014) THE INFLUENCE OF BLOOD RHEOLOGY IN SIMULATING BLOOD FLOW ON BRAIN ARTERY WITH ANEURYSM. Masters thesis, Universiti Teknologi PETRONAS.

,, MUHAMMAD YASIR (2015) THE STUDY OF MACHINABILITY AND STRESS CORROSION CRACKING OF AISI 316L STAINLESS STEEL USING END-MILLING. Masters thesis, Universiti Teknologi PETRONAS.

,, YAKUBU DAN-MALLAM (2014) INFLUENCE OF WOVEN KENAF/POLYETHYLENE TEREPHTHALATE FIBER REINFORCED POL YOXYMETHYLENE HYBRID COMPOSITE ON MECHANICAL AND PHYSICAL PROPERTIES. PhD. thesis, Universiti Teknologi PETRONAS.

,,, Ayad Kadhim (2020) Mathematical Modeling And Experimental Evaluation Of An Evacuated Tube Receiver And PVT Using Heliostat Concentrators. Doctoral thesis, Universiti Teknologi PETRONAS.

,,, Firmansyah (2016) Mixture and Thermal Stratification Effects on the RCCI Combussion in a Constant Volume Chamber. Doctoral thesis, Universiti Teknologi PETRONAS.

,,, Mohammadali Beheshti (2020) The electrochemical carbon dioxide conversion to Synthesis Gas (SYNGAS) by Zinc-Nickel bimetallic electrocatalysts. Doctoral thesis, Universiti Teknologi PETRONAS.

,,, Muhammad Ali (2020) Influence of Powder Morphology and Sintering Parameters on Powder Injection Molded Soft Magnetic Alloy. Doctoral thesis, Universiti Teknologi PETRONAS.

,,, Muhammad Sarwar (2016) Integrated Framework for On-Site Welding of Creep Strength Enhanced (CSEF) Pipes for Supercritical Conditions. Doctoral thesis, Universiti Teknologi PETRONAS.

,,, Muhammad Yasir (2016) The Study of Machinibility and Stress Corrosion Cracking Susceptibility of 316L Stainless Steel using End-Milling. Masters thesis, Universiti Teknologi PETRONAS.

,,, Muhammad Yasir (2020) Thermo-Mechanical Properties of Basalt and Glass Fiber Reinforced Intumescent Fire Retardant Coating for Structural Steel Application. Doctoral thesis, Universiti Teknologi PETRONAS.

,,, Sadaqat Ali (2020) Development and Characterization of Modified 316L Stainless Steel Alloy for Biomedical Applications using Powder Metallurgy. Doctoral thesis, Universiti Teknologi PETRONAS.

,,, Usama Khan (2020) Grid Based Dynamic Risk Analysis using CFD Simulation of Vapor Cloud Explosion Offshore Facilities. Doctoral thesis, Universiti Teknologi PETRONAS.

.

., AFOLABI LUKMON OWOLABI (2016) PERFORMANCE ENHANCEMENT OF NANO-ADDITIVES IN A FLAT-PLATE SOLAR COLLECTOR INTEGRATED WITH THERMAL ENERGY STORAGE SYSTEMS. PhD. thesis, Universiti Teknologi PETRONAS.

., AHMAD HASSAN (2016) FIRE HAZARDS & RISK ASSESSMENT IN OFFSHORE PETROLEUM FACILITIES. [Final Year Project] (Submitted)

., AZEEMUDDIN (2013) SIMULATION OF SOLAR CHIMNEY POWER PLANT WITH AN EXTERNAL HEAT SOURCE. Masters thesis, Universiti Teknologi PETRONAS.

., Brilianto Brioann Boni (2012) REMAINING CREEP LIFE PREDICTION OF USED GAS TURBINE BLADES. [Final Year Project] (Unpublished)

., Firmansyah (2007) Optimization of Injection Parameters in Compressed Natural Gas Direct Injection (CNG-DI) Spark Ignition Engine. Masters thesis, Universiti Teknologi PETRONAS.

., Koh Kelly (2016) Experimental Evaluation of Innovated Mixed Flow Wind Turbine for Updraft Solar Power Generation Systems. [Final Year Project]

., MOHD DANISH (2018) DISSERTATION TITLE: THERMAL AND SURFACE INTEGRITY STUDY OF AZ31C MAGNESIUM ALLOY INFLUENCED BY CRYOGENIC TURNING MACHINING PROCESS. PhD. thesis, Universiti Teknologi PETRONAS.

., Muhamad Fadhli Bin Rosli (2016) Mechanical Properties and Microstructural Evaluation of Dissimilar Friction Stir Weld of AA6061 Aluminium Alloy and AA5083 Aluminium Alloy. [Final Year Project]

., Muhammad Izwan Bin Hazim (2016) Investigation of Open Source Optimizers for Mechanical Design Optimization Problems. [Final Year Project]

., OBAKENG LEVY SIKO (2012) BENDING STRESS ANALYSIS OF HELICAL GEARS USING FINITE ELEMENT METHOD. [Final Year Project] (Unpublished)

., S. FAUZAN ASHRI (2012) THE EFFECTIVENESS OF MULTI-STAGED SWIRLING FLUIDIZED BED. [Final Year Project] (Unpublished)

., Syed Haider Ali Shah (2012) EFFECT OF CONDENSER CONDITIONS ON PERFORMANCE OF A STEAM POWER PLANT. [Final Year Project] (Unpublished)

., Vyner V Raya (2012) Image Reconstruction and Resolution via Electrical Impedance Tomography. [Final Year Project] (Unpublished)

., Vyner V Raya (2012) Image Reconstruction and Resolution via Electrical Impedance Tomography. [Final Year Project] (Unpublished)

.SANTHIRASEGARAN, JEIHARISH S.V (2013) IMPROVEMENT OF SOLAR PHOTOVOLTAIC MODULE EFFICIENCIES THROUGH WATER COOLING AND DEBRIS REMOVAL. [Final Year Project] (Unpublished)

@

@Sinawat, Clement Welley (2016) Investigation On the Physical, Mechanical and Corrosion Behaviour of 316L Austenitic Stainless Steel Nitriding at Elevated Temperature. [Final Year Project] (Submitted)

A

A Ganesh, Dinnassh (2021) Evaluation of Economic Production Quantity For Continuous Production System : Case Of Chilled Water Generation, Storage And Distribution. [Final Year Project] (Submitted)

A Rahim, Nurkamariah (2016) AN INVESTIGATION OF MECHANICAL PROPERTIES ON NITRIDED AUSTENITIC STAINLESS STEEL. [Final Year Project] (Submitted)

A Rahman, Hamizah (2012) Design of an Explosion Vessel for Study of Flame Propagations. [Final Year Project]

A Rahman, Hamizah (2008) Design of an Explosion Vessel for Study of Flame Propagations. [Final Year Project] (Unpublished)

A Siaramu, Arvin Kumar (2016) A Study of Corrosion Behaviour for Steels Precipitated with Paraffin Wax Precipitation. [Final Year Project] (Submitted)

A. Jalil, Adibah (2009) Study on the Application of Electronic Fuel Injection to Carburetted Single Cylinder 4 Stroke Engine. [Final Year Project] (Unpublished)

A. RAHMAN, NOOR A’IN (2018) FORMULATION AND ASSESSMENT OF PANI-EPOXY COATING RESISTANT TO HYDROGEN PERMEATION. Masters thesis, Universiti Teknologi PETRONAS.

A. Rahman, Ahmad Zairin Fadzil (2021) Failure pressure analysis of corroded pipeline with circumferential interacting defects subjected to combined loadings using FEM and ANN. [Final Year Project] (Submitted)

A. Rashid, Muhammad Hamizan (2022) Enhancement Evaluation of Experimental Solar Chimney by Extended Solar Heat Trap. [Final Year Project] (Submitted)

A. William, Moshey (2013) BULLHEADING II TWO PHASE SIMULATION OF A DEFINITIVE WELL KILL. [Final Year Project] (Unpublished)

A.AZIZ, AHMAD FAIZ (2004) INJECTION MOULDING THERMOPLASTIC COMPOSITES. [Final Year Project] (Unpublished)

A.Kumar, Ganesh (2016) An effective optimization of rainwater storage tanks for different roof materials in commercial buildings. [Final Year Project] (Submitted)

A/L AIYYAPPAN, BHUVANA RUEBEN (2016) A STUDY OF MECHANICAL PROPERTIES AND CRUSHING PERFORMANCE OF CARBON FIBER WOUND TO HDPE PIPE (CFWHP. [Final Year Project] (Submitted)

A/L ARUMUGAM, THIBANKUMAR (2019) Residual Strength Analysis of Corroded Pipe Subjected to Internal Pressure and Longitudinal Compressive Stress. Masters thesis, Universiti Teknologi PETRONAS.

A/L Arumugam, Thibankumar (2016) Characterization of Methane Based Graphene Synthesis on H13 Tool Steel. [Final Year Project] (Submitted)

A/L Christopher, Benedict Chris (2016) Evaluation On Corrosion Resistance Of X-65 Pipeline Steel To Various Species Of Microbes. [Final Year Project] (Submitted)

A/L D. Ramanujam, Keeran Daniel (2016) Mooring Analysis of Very Large Floating Structures in Malaysian South China Sea Waters. [Final Year Project] (Submitted)

A/L Dev Kumar, Sujev Kumar (2016) Enhancement of Fire Resistance of Intumescent Coatings by Basalt and Refractory-Type Hybrid Fibre. [Final Year Project] (Submitted)

A/L ELIYATHAMBY, DHANARAJ (2016) Dynamic Analysis of Stick-Slip and Bit Bounce in Oilwell Drillstring. [Final Year Project] (Submitted)

A/L Harbinder Singh, Harnamdav Singh (2011) STUDY ON CHAR EXPANSION AND HEAT SIDELDING OF INTUMESCENT COATING BASED ON INORGANIC FILLERS. [Final Year Project] (Unpublished)

A/L Kalai Chelven, A K Kartigesh (2009) Experimental and Numerical Investigation on 2-D Wing-Ground Interference. [Final Year Project] (Unpublished)

A/L Krishnasammy, Puventhan (2013) Experimental Analysis Of Modified Roof Extractor For Wind Power Conversion In Solar Chimney Application. [Final Year Project] (Unpublished)

A/L Latchumanan, Arun Raj (2015) Knowledge-Based engineering approach for optimal design of pressure vessels. [Final Year Project] (Unpublished)

A/L MUTHIAH, ARAVINDRAN (2015) INVESTIGATION OF THE EFFECTS OF DRILLSTRING DYNAMICS TO MUD FLOW BEHAVIOUR. [Final Year Project] (Unpublished)

A/L Muniandy, Prathab (2016) Dynamic Analysis of High Frequency Vibro-Impact Drilling. [Final Year Project] (Submitted)

A/L Prakasan, Arjund (2016) EFFECT OF TRANSVERSE, LONGITUDINAL AND VERTICAL SEPARATION ON DRAG FOR A FLEET OF AUTONOMOUS UNDERWATER GLIDER. [Final Year Project] (Submitted)

A/L RAMAHLINGAM, TIRUSELVAM (2012) STUDIES ON A DOUBLE TUBE HEAT EXCHANGER WITH NOVEL SURFACE ENHANCEMENT FOR SINGLE PHASE AND MULTI-PHASE HEAT TRANSFER. PhD. thesis, Universiti Teknologi PETRONAS.

A/L Ramesh, Potriyan Sivanathan (2016) Performance Evaluation of Fixed Plate Air To Air Energy Recovery Heat Exchanger in Buildings Air Conditioning System. [Final Year Project] (Submitted)

A/L THANARAJEE, SHAATIESH (2016) Vibration Analysis of Carbon Nanotube Based Bio-Sensors. [Final Year Project] (Submitted)

A/L Thavanthram, Dashindaran (2015) Development of Microwavable Diesel Soot Filters For Diesel Engine Exhaust System. [Final Year Project] (Unpublished)

A/L UTHRAPATHY, SHATHISWARAN (2015) MODELLING OF HYDRAULIC FLIP INSIDE A SCALED-UP DIESEL INJECTOR NOZZLE. [Final Year Project] (Unpublished)

A/L Vesvanathan, Dhivendra (2016) Performance study of an engine waste heat driven adsorption cooling for automotive air conditioning. [Final Year Project] (Submitted)

A/L Vijayakumaran, Harrivin (2016) Simulation of Swirling Wet Steam Flow through a Supersonic Nozzle. [Final Year Project]

A/P Sreetharan, Thevi (2015) Risk Based Integrity Modeling of Offshore Process Component Piping. [Final Year Project] (Unpublished)

AB MANAS, MOHAMAD FARIS (2013) STUDY ON THE EFFECTS OF BUTT WELD JOINT BEVEL ANGLES ON TENSILE PROPERTIES OF ALUMINUM ALLOY 6061. [Final Year Project] (Unpublished)

AB RAHMAN, AIDIL (2020) The Effect of Welding Parameters to Mechanical and Physical Properties during Resistance Welding of Titanium Alloys. [Final Year Project] (Submitted)

AB RAZAK, NIK MOHD HAFIZZAL (2013) ENERGY RECOVERY HEAT EXCHANGER PERFORMANCE IN BUILDING’S AIR CONDITIONING SYSTEM. [Final Year Project] (Unpublished)

ABBAS, SYED SAMAR (2019) NUMERICAL INVESTIGATION ON HEMODYNAMICS AND PLATELET ACTIVATION POTENTIAL OF BILEAFLET MECHANICAL HEART VALVES. Masters thesis, Universiti Teknologi PETRONAS.

ABBAS, TAHIR (2017) Evaluation of energy absorption of aluminium tube partially wrapped with glass/epoxy using Taguchi Method. Masters thesis, Universiti Teknologi PETRONAS.

ABBAS ATYA, ABBAS HASSAN (2015) COMBUSTION OF DEWATERED POULTRY SLUDGE IN A LABORATORY SCALE FLUIDIZED BED COMBUSTOR. PhD. thesis, Universiti Teknologi PETRONAS.

ABBASI, AIJAZ ALI (2019) Prediction Model for Natural Gas Hydrate Formation Property Relations. PhD. thesis, Universiti Teknologi PETRONAS.

ABD GAFAR, AMIR HAZWAN (2013) DEVELOPMENT OF RISK ASSESSMENT MODEL FOR GAS TURBINE. [Final Year Project] (Unpublished)

ABD JALIL, AHMAD IDHWAN (2015) FUZZY LOGIC CONTROL FOR ENERGY MANAGEMENT SYSTEM OF A HYBRID ELECTRIC VEHICLE. [Final Year Project] (Unpublished)

ABD JAMIL, AINI (2013) Co-gasification of Oil Palm Fronds, Wood Chips and Sugarcane Bagasse for Power Generation. [Final Year Project] (Unpublished)

ABD LATIF, MUHAMAD FAUZAN (2013) Effects of Biopolymer as Drag Reducing Agent on Characteristics of Crude Oil. [Final Year Project] (Unpublished)

ABD MAJID, ABDUL HAFIZ (2011) SPRAY CHARACTERISTIC OF GASOHOL BLENDS USING OPTICAL MEASUREMENT. [Final Year Project] (Unpublished)

ABD MOKTI, NOORAKBAR (2016) Wear Analysis of Tungsten Carbide Coated with Diamond-Like Carbon as Friction Stir Welding Tool. [Final Year Project] (Submitted)

ABD RAHMAN, MOHAMAD ZULHAKIM (2012) TENSILE AND FLEXURAL PROPERTIES OF RECYCLED PP/KENAF/PET HYBRID COMPOSITES. [Final Year Project] (Unpublished)

ABD RAZAK, MUHAMMAD ZHARIF (2011) The Effect of Current to Hardness, Microstructure and Toughness in Shielded Metal Arc Welding of Carbon Steel and Stainless Steel 304. [Final Year Project] (Unpublished)

ABDELRAHMAN ALI GASIM, ALRASHEED (2017) Joining of SiAlON to Nitrided Duplex Stainless Steel at Elevated Temperature. [Final Year Project]

ABDU ALIYU, ABDUL’AZEEZ (2019) COATING OF BULK METALLIC GLASS THROUGH ELECTRO-DISCHARGE PROCESS FOR POTENTIAL ORTHOPEDIC APPLICATION. PhD. thesis, Universiti Teknologi PETRONAS.

ABDUL AZIZ, MOHAMMAD IQBAL (2012) Rotary Friction Welding of Copper Rods by Utilizing Lathe Machine. [Final Year Project] (Unpublished)

ABDUL GHAFFAR, AMIR FARID (2012) PALM OIL FIBER COMPOSITE LEAF SPRING FOR HEAVY VEHICLE. [Final Year Project] (Unpublished)

ABDUL GHANI ZUKRI, MUHAMMAD SHAFIQ (2021) STUDY OF EFFECTIVENESS BENZOTRIAZOLE LOADED HALLOYSITE NANOTUBE IN EPOXY AS ANTICORROSION COATING ON CARBON STEEL. [Final Year Project] (Submitted)

ABDUL HAMID, MUHAMMAD HAZIEM (2013) EXPERIMENTAL STUDY ON PIPE FLUID INDUCED VIBRATION. [Final Year Project] (Unpublished)

ABDUL HANAN, MOHD SYAHID (2013) CENTRIFUGAL COMPRESSOR VIBRATION ANALYSIS. [Final Year Project] (Submitted)

ABDUL JAMIL, IYLIA ELENA (2017) ANALYSIS OF OIL/WATER EMULSION IN THE PRODUCTION AND DUMPING ZONES OF OIL WELL BY CFD TECHNIQUE. Masters thesis, Universiti Teknologi PETRONAS.

ABDUL LATIF, MUHAMMAD FADHIL (2013) Friction Stir Welding (FSW): The effect of tilting angle. [Final Year Project] (Unpublished)

ABDUL MALEK, NOR HAFIZAH (2008) ULTRASOUND AIR BUBBLE DETECTOR FOR MOVING BLOOD (ARTIFICIAL KIDNEY APPLICATION). [Final Year Project] (Unpublished)

ABDUL MANAP, ABDUL RAHMAT (2017) ANALYSIS ON THE EFFECT OF SEAT LOADING DISTRIBUTION AND VEHICLE PARAMETERS ON HIGH-DECK BUS ROLLOVER PROPENSITY. Masters thesis, Universiti Teknologi PETRONAS.

ABDUL MUTTALIB, MOHD FADHIL HARFIEZ (2019) FUEL CHARACTERIZATION AND COMBUSTION MODELLING OF POULTRY PROCESSING DEWATERED SLUDGE IN A BUBBLING FLUIDIZED BED REACTOR. PhD. thesis, Universiti Teknologi PETRONAS.

ABDUL RAHMAN, KHAIRIN EZZATY (2012) EXPERIMENTAL AND SIMULATION STUDY ON THE EFFECTS OF TUBE COIL PLATES ON THE PERFORMANCE OF STEAM PACKAGED BOILER. [Final Year Project] (Unpublished)

ABDUL RANI, MOHD AMIRUL FIKRI (2013) STUDY OF POSSIBLE FIRE DOOR MATERIALS MADE FROM ALTERNATIVE WASTE ITEMS. [Final Year Project] (Unpublished)

ABDUL RAZAK, ABDUL FALIQ QUSHAIRI (2013) Estimating Solar Energy Potential in Perak using Clearness Index and Artificial Neural Network. [Final Year Project] (Unpublished)

ABDUL RAZAK, ABDUL FALIQ QUSHAIRI (2013) Estimating Solar Energy Potential in Perak using Clearness Index and Artificial Neural Network. [Final Year Project] (Unpublished)

ABDUL RAZAK, MUHAMMAD AL’HAPIS (2018) PARTICLES MIXED ELECTRO-DISCHARGE MACHINING OF MAGNESIUM ALLOY FOR IMPLANTS APPLICATION. PhD. thesis, Universiti Teknologi PETRONAS.

ABDUL SAMAD, MUHAMMED FARHAN (2012) TRIBOLOGICAL PERFORMANCE OF ADDITIVES IN COMMERCIAL LUBRICANTS. [Final Year Project] (Unpublished)

ABDUL WAHHAB, HASANAIN ADNAN (2018) MAGNETO-HYDRODYNAMIC EFFECTS ON DIESEL/CNG BUBBLY FLOW IN A HORIZONTAL PIPE. PhD. thesis, Universiti Teknologi PETRONAS.

ABDULLAH, MUHAMAD ADLAN (2008) Engine Performance and Combustion Characteristics of Hydrogen in a Direct Injection Engine. Masters thesis, Universiti Teknologi PETRONAS.

ABDULLAH MAHMOUD Y, ALSOMALI (2017) THE EFFECTS OF THERMOPLASTIC OLEFIN (TPO) ON MECHANICAL PROPERTIES OF RECYCLED POLYPROPYLENE (r-PP). [Final Year Project]

ABDULMALEK, SHAYMAA HUSHAM (2019) DEVELOPMENT AND EVALUATION OF HYBRID SOLAR-THERMAL DESICCANT MULTI-CHAMBER DRYER FOR IMPROVING DRYING UNIFORMITY. PhD. thesis, Universiti Teknologi PETRONAS.

ABU HAMIN, MOHD ZULKIFLY (2013) FINITE ELEMENT ANALYSIS OF RESIDUAL STRESS IN WELDED THICK PLATES OF A SINGLE V BUTT WELD WITH DIFFERENT INCLUDED BEVEL ANGLES. [Final Year Project] (Unpublished)

ABU SAMAH, IZATUL NADIA (2011) Study on Wet Method Mechanism for Producing Tronoh's Silica Sand Fine Particles. [Final Year Project] (Unpublished)

ABU SAMAR, MUHAMAD ASRI (2011) Mineral Derived from Fine Clay Isolated from Potter Wasp Nest CoUected from Universiti Teknologi PETRONAS (UTP) Main Hall. [Final Year Project] (Unpublished)

ABU TALIB, MUHAMMAD HAFIZ (2011) STUDY ON THE CHARACTERIZATION OF SILICA SAND NANOPARTICLES-IRON BASED COMPOSITES (Fe-Si02) USING NITROGEN ATMOSPHERE AS SINTERING ENVIRONMENT. [Final Year Project] (Unpublished)

ADAM, IBRAHIM KHALIL (2018) COMBUSTION PERFORMANCE OF RUBBER SEED AND PALM OIL BIODIESEL FUEL BLENDS WITH ANTIOXIDANTS. PhD. thesis, Universiti Teknologi PETRONAS.

ADAMU, MUSA (2018) DEVELOPMENT OF NANOSILICA MODIFIED HIGH VOLUME FLY ASH ROLLER COMPACTED RUBBERCRETE FOR PAVEMENT APPLICATION. PhD. thesis, Universiti Teknologi PETRONAS.

ADENAN, AHMAD AFIFUDDIN (2015) LIFE CYCLE ASSESSMENT OF PALM OIL MILL. [Final Year Project] (Unpublished)

ADHI, VINCENT ADRIAN (2017) MODELLING AND OPTIMIZATION OF HYBRID POWER SYSTEMS FOR RURAL AREAS. [Final Year Project]

AGUNG, ASKAR TRIWIYANTO BRONTO (2014) Surface Characteristics and Performance of Stainless Steel AISI 316L of Low Temperature Hybrid Thermochemical Treatment. PhD. thesis, Universiti Teknologi PETRONAS.

AHMAD, RABI KABIR (2021) EXPERIMENTAL INVESTIGATION ON COCONUT SHELL BIOMASS PYROLYSIS USING A DOWNDRAFT REACTOR FOR CHARCOAL PRODUCTION. Doctoral thesis, UNSPECIFIED.

AHMAD, MOHD FADZIL ALI (2018) Improving Performance of Wet-Gas Separator Through Compact Supersonic Vertical Configuration. PhD. thesis, Universiti Teknologi PETRONAS.

AHMAD BADARUDDIN, NUR AQILAH (2021) SIMULATION STUDY ON FUEL COMBUSTION OF WATER-TUBE BOILER IN PALM OIL MILL. [Final Year Project] (Submitted)

AHMAD HASNULNAIM BIN CHE KAMARUDDIN, AHMAD HASNULNAIM (2011) EFFECT OF ENERGY RECOVERY ON THE HOISTING CRANE ADAPTING CLOSED LOOP HYDRAULIC HOISTING SYSTEM. [Final Year Project] (Unpublished)

AHMAD JAAL, RAFIDA (2018) INVESTIGATION OF CORROSION INHIBITION MECHANISM OF IMIDAZOLINE-BASED INHIBITOR IN CO2 ENVIRONMENT USING ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY (EIS). Masters thesis, Universiti Teknologi PETRONAS.

AHMAD KAMAL, NURUL ATIQAH (2017) CORROSION IMPACT AND COMPATIBILITY STUDY OF METALLIC MATERIALS WITH BIODIESEL FUEL. [Final Year Project]

AHMAD KAMAL, UMAR MUSLIM (2021) DEVELOPMENT OF ANALYSIS STUDY ON MAINTENANCE DOWNTIME (MAINTAINABILITY) OF EQUIPMENT AND SYSTEM IN PETROCHEMICAL PLANT. [Final Year Project] (Submitted)

AHMAD MAJDI, KHAIRUL NAZMI (2011) PERFORMANCE IMPROVEMENT OF PHOTOVOLTAIC PANELS THROUGH MITIGATION OF SURFACE TEMPERATURE COOLING AND DEBRIS REMOVAL. [Final Year Project] (Unpublished)

AHMAD NIZAM, NUR FARAH IZZATI (2017) INFLUENCE OF SUBSTRATE ENERGY ON THE ADHESION COMPATIBILITY OF EPOXY ADHESIVE USING MOLECULAR SIMULATION TOOL. [Final Year Project]

AHMAD SHAKARIA, AHMAD FARIS ASLAM (2020) DEVELOPMENT OF AN ELECTROSTATIC DISCHARGE (ESD) EVENT DETECTOR SYSTEM FOR AN ELECTRONIC MANUFACTURING PRODUCTION LINE. [Final Year Project] (Submitted)

AHMAD ZAINUDIN, MUHAMMAD FAIZ (2017) FEASIBILITY STUDY ON SUPERSONIC CENTRIFUGE FOR FREE WATER REMOVAL FROM BIOGAS. [Final Year Project] (Submitted)

AHMAD ZUHAIRIE BIN YAHYA, AHMAD (2012) EFFECTS OF FIBER LENGTH ON FIRE PERFORMANCE OF INTUMESCENT FIRE RETARDANT COATING. [Final Year Project] (Unpublished)

AHMED BHAYO, BILAWAL (2015) AN EXPERIMENTAL INVESTIGATION ON PERFROMANCE ASSESSMENT OF S-ROTORS FOR STAND-ALONE WIND POWER SYSTEM. Masters thesis, Universiti Teknologi PETRONAS.

AHMED YASSEN, TADAHMUN (2015) DEVELOPMENT AND EVALUATION OF SOLAR THERMAL HYBRID DRYING SYSTEM. PhD. thesis, Universiti Teknologi PETRONAS.

AHSAN, SHAZAIB (2019) PROGNOSIS AND RELIABILITY MODELLING FOR HEALTH MONITORING OF INDUSTRIAL GAS TURBINES. Masters thesis, Universiti Teknologi PETRONAS.

AJA, OGBOO CHIKERE (2013) INVESTIGATION ON HYBRID SOLAR-FLUE GAS CHIMNEY POWER PLANT. PhD. thesis, Universiti Teknologi PETRONAS.

AKBAR, AHMAD RADIKAL (2016) DEVELOPMENT OF AUTO-REINFORCE MAGNETIC FLYWHEEL AS REGENERATIVE ENERGY STORAGE FOR AUTOMOBILE ENGINE. Masters thesis, Universiti Teknologi PETRONAS.

AKBAR, JASMAINE MARSELLA (2011) EFFECTS OF DRILLING PARAMETERS ON HOLE INTEGRITY WHEN DRILLING HYBRID FIBER COMPOSITE HALF CYLINDERS. [Final Year Project] (Unpublished)

AKHTER, JAVE (2021) THEORETICAL AND EXPERIMENTAL EVALUATION OF A MODIFIED COMPOUND PARABOLIC CONCENTRATING SOLAR COLLECTOR USING OIL-BASED NANOFLUIDS. Doctoral thesis, UNSPECIFIED.

AKHTER, JAVED (2020) THEORETICAL AND EXPERIMENTAL EVALUATION OF A MODIFIED COMPOUND PARABOLIC CONCENTRATING SOLAR COLLECTOR USING OIL-BASED NANOFLUIDS. PhD. thesis, Universiti Teknologi PETRONAS.

AKILU, SULEIMAN (2013) NUMERICAL STUDY OF FREE CONVECTION BOUNDARY LAYER FLOW OF A NANOFLUID PAST AN ISOTHERMAL INCLINED PLATE. Masters thesis, UTP.

AKILU, SULEIMAN (2018) EXPERIMENTAL INVESTIGATION OF FORCED CONVECTION HEAT TRANSFER WITH SINGLE AND HYBRID NANOFLUIDS FOR ENERGY TRANSPORT ENHANCEMENT. PhD. thesis, Universiti Teknologi PETRONAS.

AKLILU, TESFAMICHAEL BAHETA (2010) MATHEMATICAL MODELING AND STATISTICAL EVALUATION OF COGENERATION PLANT IN TROPICAL REGION. PhD. thesis, Universiti Teknologi PETRONAS.

AL BATATI, NABIL (2015) SIMULATION OF DRILL STRING VIBRATION DUE TO RISER'S OSCILLATION. Masters thesis, Universiti Teknologi PETRONAS.

AL RIZA, DIMAS FIRMANDA (2011) SIZING OPTIMIZATION OF STANDALONE PHOTOVOLTAIC SYSTEM FOR RESIDENTIAL LIGHTING. Masters thesis, Universiti Teknologi Petronas.

AL-AMIN, MD (2021) COATING OF BIOMEDICAL GRADE 316L STAINLESS STEEL WITH HA/MWCNT USING PM-EDM PROCESS. Masters thesis, Universiti Teknologi Petronas.

ALAM, MD. AZAD (2022) SYNTHESIS AND CHARACTERIZATION OF ALUMINUM BASED HYBRID COMPOSITES FOR ENGINEERING APPLICATIONS. Doctoral thesis, UNSPECIFIED.

ALI, SADAQAT (2020) DEVELOPMENT AND CHARACTERIZATION OF MODIFIED 316L STAINLESS STEEL ALLOY FOR BIOMEDICAL APPLICATIONS USING POWDER METALLURGY. PhD. thesis, Universiti Teknologi PETRONAS.

ALI AZMAN BIN OMAR, ALI AZMAN (2008) INVESTIGATION ON STRESS CONCENTRATION FACTOR OF PIPING BRANCH JUNCTIONS SUBJECTED TO INTERNAL PRESSURE. [Final Year Project] (Unpublished)

ALI GASIM, ALRASHEED ABDELRAHMAN (2017) Joining of SiAlON to Nitrided Duplex Stainless Steel at Elevated Temperature. [Final Year Project]

ALIAS, MOHAMMAD IZZAT (2018) NUMERICAL SIMULATION OF IN-CYLINDER HEAT TRANSFER LOSSES FROM DIESEL ENGINE. [Final Year Project] (Submitted)

ALIF SYAHRIZAD BIN RAMLI, ALIF SYAHRIZAD (2010) Study on Influences of Rear-Wheel Turn Angle to Performance of Four Wheel Steering (4WS) Vehicle. [Final Year Project] (Unpublished)

AMAR SINGH, JASPREET KAUR (2013) THERMAL SHRINKAGE AND YIELD STRENGTH OF GELLED WAXY CRUDE OIL. Masters thesis, UTP.

AMIN ABDELKHALIQ EL AMIN MOHAMED, AMIN ABDELKHALIQ (2009) Absorption and Desorption Of Hydrogen in Metal Hydrides. [Final Year Project] (Unpublished)

AMIR, NORLAILI (2013) DEVELOPMENT OF MINERAL AND CARBON FIBRES REINFORCED INTUMESCENT COATINGS FOR STEEL STRUCTURES. PhD. thesis, Universiti Teknologi PETRONAS.

AMIR, ADIBAH (2016) WEAR MECHANISM OF IRON COMPOSITE REINFORCED WITH SILICA. PhD. thesis, Universiti Teknologi PETRONAS.

AMIR SOFFIAN, MUHAMMAD ASHRAF (2021) NUMERICAL MODELING OF SUPERHEATED STEAM CONDENSATION IN HEAT EXCHANGER. [Final Year Project] (Submitted)

AMIRUL LUTHFI CHAN, HAZIQ LUTHFI (2016) Experimental Study on the Impact of Wet Sand Particle to the Erosion of Mild Steel Plate. [Final Year Project] (Submitted)

ANAK JAMIT, ADRIAN EE (2009) Feasibility Study of Using Turbine for Small Scale Power Generation. [Final Year Project] (Unpublished)

ANANDARAJAH, YASHADINI (2013) UTILIZATION OF DIRECT SOLAR RADIATION FOR INDOOR LIGHTING. [Final Year Project] (Unpublished)

ANNANUR , KIZILOV (2009) FEASffiiLITY STUDY OF JATROPHA BASED MUD FOR IDGH PRESSURE LOW TEMPERATURE WELLS. [Final Year Project] (Unpublished)

APPASAMY, JEVITHA SRI (2018) EVALUATION OF N-DOPED TiO2/SWCNT COATING LAYER FOR SELF-CLEANING SOLAR PHOTOVOLTAIC CELL APPLICATION. Masters thesis, Universiti Teknologi PETRONAS.

ARIFF SHAH, ABDUL (2017) FINITE ELEMENT ANALYSIS OF SOLID-STATE THERMOELECTRIC GENERATOR WITH VARYING CONFIGURATIONS. [Final Year Project]

AROGUNDADE, ADIAT IBIRONKE (2018) CHAR-REINFORCING EFFETCS OF BAUXITE RESIDUE IN PHOSPHATEBASED INTUMESCENT COATING SYSTEM. PhD. thesis, Universiti Teknologi PETRONAS.

ARUMUGAM, UVANISWARAN (2017) INTERNAL COMBUSTION ENGINE INTAKE MANIFOLD AIR FLOW OPTIMIZATION. [Final Year Project]

ASLAM, MUHAMMAD (2016) Powder Injection Molding of Modified 316L Stainless Steel for Dental Implant Application. PhD. thesis, Universiti Teknologi PETRONAS.

AUNG MYINT OO, AUNG (2011) Knowledge Based Management For Rotating Equipment Diagnostics. [Final Year Project] (Unpublished)

AUNG NYEIN HAN, AUNG NYEIN (2011) Empirical Modeling for Diffusion of Nitrogen into AISI 430 Ferritic Stainless Steel. [Final Year Project] (Unpublished)

AUNG NYEIN HAN, AUNG NYEIN (2011) Empirical Modeling for Diffusion of Nitrogen into AISI 430 Ferritic Stainless Steel. [Final Year Project] (Unpublished)

AURYBI, MOHAMMED ABDULNABI (2018) PERFORMANCE ENHANCEMENT OF SOLAR CHIMNEY POWER PLANT SUPPLEMENTED WITH EXTERNAL HEAT SOURCE. PhD. thesis, Universiti Teknologi PETRONAS.

AWAN MAPER, ATER ISAAC (2017) STRESS ANALYSIS OF SPUR GEARS, WITH TIP RELIEF. [Final Year Project]

AZFAR BIN JASNI, AZFAR (2012) Study on Effect of 5 wt. % of Coconut Fiber Reinforcement on Tensile and Flexural Properties of Epoxy Based Composites. [Final Year Project] (Unpublished)

AZIZ AL-WAKEEL, HAITHAM BEHNAM (2015) INVESTIGATION OF LOCALIZED RAPID SOOT OXIDATION USING METALASSISTE HIGH FREQUENCY ELECTROMAGNETIC HEATING. PhD. thesis, Universiti Teknologi PETRONAS.

AZIZI, MUHAMMAD FAKHRU RAZI (2020) Finite Element Analysis of Disbondment in Thermoplastics Composite Pipe (TCP) Fitness for Surface (FFS). [Final Year Project] (Submitted)

Aaron Ang Kok Wye, Aaron (2008) Design of an Exhaust System For The UTP Formula SAE Race Car. [Final Year Project] (Unpublished)

Ab Hadi, Muhamad Naqiuddin (2016) Cellular Core Sandwich Structures for Offshore Construction. [Final Year Project] (Submitted)

Ab Halim, Mohammad Farhan (2017) Corrosion Under Insulation Testing and Simulation of Insulated Piping. [Final Year Project]

Ab Hamid, Abdul Halim (2012) DEVELOPMENT OF INTUMESCENT FIRE RETARDANT COATING FOR PROTECTION OF WOODS. [Final Year Project] (Unpublished)

Ab Manaf, Nuratiqah (2013) Remaining Fatigue Life Assessment by Using Crack Growth Model. [Final Year Project] (Unpublished)

Ab Rahim, Eleena Aqmal (2015) Simulation Study on Braided Hose Failure in Major Equipment at PETRONAS Carigali Sdn Bhd (PCSB). [Final Year Project] (Unpublished)

Ab Rahman, Luqman Nur Hakim (2016) VOLTAGE STABILITY ANALYSIS FOR ENSURING POWER SYSTEM STABILITY. [Final Year Project] (Submitted)

Ab. Aziz, Muhammad Yusri Hafiz (2020) Electrochemical Impedance Spectroscopy Evaluation of Non-Metallic Pipe (NMP) Degradation in CO2 Environment. [Final Year Project] (Submitted)

Ab. Ghani, Mohamad Fadhly (2004) Study on Cathodic Protection Principles and Requirements of Underground Steel Pipes (Concept and Laboratory/model Scale). [Final Year Project] (Unpublished)

Ab. Kadir, Nuraqliah (2016) SIMULATION STUDY ON SMART SPRINKLER FOR UNIFORMITY IMPROVEMENT. [Final Year Project] (Submitted)

Abang Usop, Dayang Farhana Syafiah (2011) The Effects of Recycled Polypropylene/Wood Flour (r-PPIWF) Composites with and without Coupling Agent on Mechanical Properties. [Final Year Project] (Unpublished)

Abbas Atya, Abbas Hassan (2016) Characteristic Study and Combustion of Dewatered Poulty Sludge in a Laboratory Scale Fluidized Bed Combustor. Doctoral thesis, Universiti Teknologi PETRONAS.

Abd Aziz, Mohd Naqiuddin Afiq (2015) Dynamic Loading on Carbon Fiber Wind to HDPE Composite Pipe (CFWHCP). [Final Year Project] (Unpublished)

Abd El-Aziz, Omar Eid Khorshed (2013) Subsea Production Control System Modelling. [Final Year Project] (Unpublished)

Abd Ghani, Ahmad Majdi (2006) DESIGN OF SOLID STATE-BASED THERMOELECTRIC DEVICE FOR COOLING AND HEATING DRINKS IN A CAR. [Final Year Project] (Unpublished)

Abd Karim, Muhammad Amin (2013) The Development of Reliability Analysis Toolkit (RAT) For Analyzing Plant Maintenance Data. [Final Year Project] (Unpublished)

Abd Koha, Mohd Muslim (2013) Subsea Production System (SPS) Control Modelling. [Final Year Project] (Unpublished)

Abd Majid, Zulfadhli (2011) Performance Investigation of Wind Rotor in Open and Bounded Environments. [Final Year Project] (Unpublished)

Abd Manaf, Aiman Shaker (2021) The Effect Of Origami-Inspired Quadrilateral Mesh On The Mechanical Behaviour Of Carbon Fiber Reinforced Silica Composite. [Final Year Project] (Submitted)

Abd Rahim, Muhamad Hanafi (2012) Aerodynamic Study of Delfy Hovering Flapping Wing. [Final Year Project] (Unpublished)

Abd Rahim, Muhammad Yusof (2008) Pressure as an Indicator for Water Breakthrough for Horizontal Well Completion. [Final Year Project] (Unpublished)

Abd Rahman, Mohd Safuan (2009) Study of Mist Elimination System. [Final Year Project] (Unpublished)

Abd Rashid, Muhamad Naim (2016) Wear Resistance Study of Nitrided ASS 316L Above The Sensitization Temperature of 1200oC. [Final Year Project] (Submitted)

Abd Rashid, Muhammad Afiq (2015) Oil Demand Forecasting in Malaysia in Transportation Sector using Artificial Neural Network (ANN). [Final Year Project] (Unpublished)

Abd Rashid, Mumtaz Hayati (2012) Design of Molten Salt Thermal Storage Tank. [Final Year Project] (Unpublished)

Abd Razak, Mohd Ariffan (2011) Assessment on Design for Manufacturing (DFM) and Design for Assembly (DFA) of a Centrifuge. [Final Year Project] (Unpublished)

Abd Razak, Nurul Fatimah (2012) PRELIMINARY STUDY FOR METHANE GENERATION OF FELCRA NASARUDDIN USING ANAEROBIC DIGESTION. [Final Year Project] (Unpublished)

Abd. Malek, Ammar Ariffin (2015) Hydrostatic Burst Test of Multi-Angle Filament Wound Composite Pipe. [Final Year Project] (Unpublished)

Abd. Rahman, Farah (2009) Design Optimization of a 2-Phase Gas/Liquid Separator. [Final Year Project] (Unpublished)

Abd. Rahni, Ashraf Aizzuddin (2011) Energy Audit of Sewage Treatment Plants. [Final Year Project] (Unpublished)

Abdalla, Abdulrahman Yousif (2016) Experimental and Numerical Simulation Investigations of Non-Newtonian Flow in Straight and Curved Pipes for Drag Reduction. Masters thesis, Universiti Teknologi PETRONAS.

Abdelwahid, Mohamed Noureldin (2008) STUCK DRILL PIPE WHILE DRILLING OPERATION. [Final Year Project] (Unpublished)

Abdul Aziz, Aisar Amiree (2020) Development of an empirical model for energy usage and machine maintainability: palm oil pressing. [Final Year Project] (Submitted)

Abdul Basith, Mohammad Sobir (2020) Effects on Number of Supports on Vibration and Stress Distribution for Piping System. [Final Year Project] (Submitted)

Abdul Hadi Bin Alias, Abdul Hadi (2010) Failure Analysis of Ethylene Cracking Heater, ET-O-F-105 Tube. [Final Year Project] (Unpublished)

Abdul Hafeez Bin Abdul Shukur, Abdul Hafeez (2012) A Study of Stability and Vibration of the Drill String. [Final Year Project] (Unpublished)

Abdul Hafiz Bin Abd Majid, Abdul Hafiz (2011) Spray Characteristic of Gasohol Blends Using Optical Measurement. [Final Year Project] (Unpublished)

Abdul Hafiz Bin Abd Majid, Abdul Hafiz (2011) Spray Characteristic of Gasohol Blends Using Optical Measurement. [Final Year Project] (Unpublished)

Abdul Halim, Anis Farhana (2011) A Study on Centrifugal Compressor Performance and Developing Compressor Performance Analysis Software. [Final Year Project] (Unpublished)

Abdul Halim, Muhammad Hafiz (2021) THE INFLLUENCE OF TEMPERATURE ON THE CORROSION BEHAVIOUR OF GLASS FIBRE REINFORCED POLYMER STRENGTHENED STEEL. [Final Year Project] (Submitted)

Abdul Halim Koh, Abdul Rahman (2008) Failure Investigation of a Steel Pipe. [Final Year Project] (Unpublished)

Abdul Halim bin Razak , Abdul Halim (2010) The Effects Of Applied Potential And Coating Thickness On Cathodic Disbondment Of Polyurea Coating. [Final Year Project] (Unpublished)

Abdul Hamid Albakri, Mohammad Faris Al Hanis (2013) A Study of Chemical Compatibility between Corrosion Inhibitor and Biocide in Offshore Application. [Final Year Project] (Unpublished)

Abdul Hapidz, Ahmad Firdaus (2005) Design and implementation of a two-wheeled balancing robot / by Ahmad Firdaus Bin Abdul Hapidz, TJ 211.35 .A286 2005. [Final Year Project]

Abdul Hazim Bin Rahmat, Abdul Hazim (2010) Improvement Of Engine Performance To Reduce Fuel Consumption Of �A Single Cylinder Spark Ignition Engine. [Final Year Project] (Unpublished)

Abdul Kadir, Mohammad Faizal (2013) DESIGN SUBSEA POWER GENERATION SYSTEM. [Final Year Project] (Unpublished)

Abdul Malek, Raez Edriezal (2013) Design and Site Implementation of Hydro-electrifier. [Final Year Project] (Unpublished)

Abdul Malek, Wan Nuradila (2016) Mechanical Properties of Recycled HDPE-Areca Leaf Sheath Fiber Composite. [Final Year Project] (Submitted)

Abdul Manan, Muhammad Aiman (2013) Effectiveness of Air and Biomass Heating using Waste Heat from a Gasification System. [Final Year Project] (Unpublished)

Abdul Rahim, Mohamad Syazwan (2016) Structural Analysis of Rotating Baffles in a CO2 Separator. [Final Year Project] (Submitted)

Abdul Rahim, Muhammad Adib (2016) Design and Development of 3D Printed Robotic Gripper. [Final Year Project] (Submitted)

Abdul Rahim, Muhammad Fadhlilah Bin (2009) Preliminary Stress Analysis on Beam Surface As A Result of Char Expansion In A Fire Exposed Intumescent Coating. [Final Year Project] (Unpublished)

Abdul Rahman, Nur Aimy Aqilah (2022) Simulation of Lazy Steel Wave Riser Bend Radius – New Configuration of Shaped Steel Lazy Wave Riser (SLWR). [Final Year Project] (Submitted)

Abdul Rahman, Mohd Ridzuan (2016) Tensile and Flexural Properties of Woven Micro-Braided Yarn Composite. [Final Year Project] (Submitted)

Abdul Rahman, Muhammad Izzat (2012) Design and Fabrication of Brushless DC Motor Driven Personal Electric Vehicle (PEV). [Final Year Project] (Unpublished)

Abdul Rahman Bin Abdul Halim Koh, Abdul Rahman (2008) Failure Investigation of a Steel Pipe. [Final Year Project] (Unpublished)

Abdul Rahman Bin Mohd Zafrullah, Abdul Rahman (2011) Tribological Properties Analysis on Nitrided AISI 316L Stainless Steel. [Final Year Project] (Unpublished)

Abdul Rashid, Mohd Wafiuddin (2011) FINITE ELEMENT ANALYSIS OF RESIDUAL STRESSES IN 316 STAINLESS STEEL PIPELINES SMAW WELDING. [Final Year Project] (Unpublished)

Abdul Rashid, Nurlianah (2011) Variation of High Temperature Gas Nitriding Time on Duplex Stainless Steels. [Final Year Project] (Unpublished)

Abdul Rasid, Muhammad Ridhwan (2011) Development of A Model for Technical and Commercial Evaluation of Rotating Equipment for Offshore Plant. [Final Year Project] (Unpublished)

Abdul Rauf Mohamad Nahar, Abdul Rauf (2010) Design of a Steering Linkage Mechanism for a Simple Three Wheeled Car. [Final Year Project] (Unpublished)

Abdul Razak, Hafizhun Husna (2022) Development of Reliability, Availability and Maintainability (RAM) Model for Solar PV System. [Final Year Project] (Submitted)

Abdul Razak, Azrie (2018) Analysis on Resin Starvation Issue in Carbon Fibre on J-Nose Panel. [Final Year Project] (Submitted)

Abdul Razak, Mohamad Anas Najmi (2011) Study on the Effect of Annealing Temperature on the Compressibility and Microscopic Structure of Pure Graphite. [Final Year Project] (Unpublished)

Abdul Razak bin Rustami, Abdul Razak (2008) A Study into the Effect of Loading and Sliding Speed to the Tribological Properties of Brake Pad Material. [Final Year Project] (Unpublished)

Abdul Wahab, Ahmad Izzat bin (2009) NC Codes Library for Pump Impeller Machining. [Final Year Project] (Unpublished)

Abdul Wahab, Mohamad Husaini (2011) Study on Epoxy Mastic Coating of Submerge Structure. [Final Year Project] (Unpublished)

Abdul Wahab, Mohamad Husaini (2011) Study on Epoxy Mastic Coating of Submerge Structure. [Final Year Project] (Unpublished)

Abdul Wali, Muhamad Ammar (2016) Study of Force Feedback in Steer-By-Wire Vehicles for Driving Simulator. [Final Year Project] (Submitted)

Abdul! Aziz, Nor Azida (2004) Modeling and Simulation of Nonisothermal Plug Flow Reactor for Methanol Synthesis Via Methyl Acetate Saponification. [Final Year Project] (Unpublished)

Abdull Hadi, Mohd Ameerul Haziq (2020) To Study the Effect of Waste Glass Powder and Zirconium Phosphate on the Properties of Intumescent Fire-Retardant Coating. [Final Year Project] (Submitted)

Abdullah, Abdul Hanif (2016) Effect of Ferrous (. [Final Year Project] (Submitted)

Abdullah, Abdul Haris (2016) The Comparison between SMAW and FSW Performances on Microstructure, Hardness and Corrosion Susceptibility of Carbon Steel. [Final Year Project] (Submitted)

Abdullah, Ahmad Afif (2016) Solar Desiccant Cooling System. [Final Year Project] (Submitted)

Abdullah, Ahmad Zaimmul Adli (2021) Remaining Useful Life Assessment of Pipeline via Finite Element Analysis and FITNET FFS Method by Evaluating Burst Pressure of Cylindrical Pipeline and Probabilistic Method. [Final Year Project] (Submitted)

Abdullah, Kamal Hanafi (2021) DEVELOPMENT OF RELIABILITY, AVAILABILITY AND MAINTAINABILITY MODEL FOR RECIPROCATING COMPRESSOR IN MRCSB. [Final Year Project] (Submitted)

Abdullah, Muhammad Al Fikhri (2016) Analysis of Instabilities Dynamics in Discontinuous Stratified Flow in Horizontal Pipeline. [Final Year Project] (Submitted)

Abdullah Mahmoud Y, Alsomali (2017) THE EFFECTS OF THERMOPLASTIC OLEFIN (TPO) ON MECHANICAL PROPERTIES OF RECYCLED POLYPROPYLENE (r-PP). [Final Year Project]

Abdullah Sani, Meor Hamzah (2004) SURFACE FINISH STUDY OF GREY CAST IRON CASTING SAMPLES FROM CONVENTIONAL & NON CONVENTIONAL MACHINING PROCESSES. [Final Year Project] (Unpublished)

Abid Haq bin Abdul Aziz, Abid Haq (2010) Electrochemical Impedance Spectroscopy (EIS) Analysis of Film Formation in CO2 Corrosion. [Final Year Project] (Unpublished)

Abu, Fadhilatul Hikmah (2013) Design and Analysis of Recovery Net Landing for UAV ALUDRA MR-01. [Final Year Project] (Unpublished)

Abu Bakar, Abu Amirul Shafiq (2020) Study on the Mechanical Behavior of Al - 7075 after Heat Treatment Process in Biomedical Field. [Final Year Project] (Submitted)

Abu Bakar, Khairunnisa (2012) Finite Element Analysis of Violin Bridge. [Final Year Project] (Unpublished)

Abu Bakar, Mohd Redzuan (2011) Palm Oil Fronds as Alternative Source of Raw Material to Produce Pulp and Paper. [Final Year Project] (Unpublished)

Abu Bakar, Muhamad Faizal (2001) Study of the Effect of Patch Bonded Surface Area and Shape on Flexural Strength of Glass/Polyester Composite using External Bonded Repair Technique. [Final Year Project] (Unpublished)

Abu Bakar, Muhammad Al-Afiq (2013) Tensile Strength Of Polyester/Woven Kenaf Composites. [Final Year Project] (Unpublished)

Abul Kalam Azad, Nursyhira Azad (2020) Investigation of Tribological Properties of Hybrid HDPE Polymer Nano Composites. [Final Year Project] (Submitted)

Adam, Mohd Farid (2016) Numerical and Simulation Analysis of PDC cutter Associated with the Rate of Penetration. [Final Year Project] (Submitted)

Adam Hareezi Abdul Aziz, Adam Hareezi (2010) Three-Dimensional (3D) Reconstruction of Microstructures via Serial Sectioning. [Final Year Project] (Unpublished)

Adanan@Adnan, Ahmad Yumnie (2013) Controlling Sand Production Problem in Open-Hole Completion; a Case Study. [Final Year Project] (Unpublished)

Adi Akmal Bin Nasrul Hisham, Adi Akmal (2008) Study and Improvement of Drag Coefficient of a Bus. [Final Year Project] (Unpublished)

Adnan, Adni Hashira (2016) Evaluation of Carbon Dioxide Emission of Plate Heat Exchanger for Chilled Water Distribution. [Final Year Project] (Submitted)

Adnan, Muhammad Adham (2015) Influence of Heat Treatment Process on Carbon Steel Pipe Corrosion in The Presence of Carbon Dioxide, CO2 and Acetic Acid, HAc. [Final Year Project] (Unpublished)

Adnan, Nurfatin Ezzuni (2013) A study of hardness and the sensitization of nitrided martensitic stainless steel during cooling down process. [Final Year Project] (Unpublished)

Afandi, Muhammad Syafiq (2013) The Study of Flow Dynamics in Long Pipeline for the Transport of Carbon Dioxide (CO2). [Final Year Project] (Unpublished)

Afiza Binti Johri, Afiza (2008) Minimizing Sand Erosion in Subsea Production System (SPS) Choke Valve. Other thesis, Universiti Teknologi Petronas.

Afrooz, Iman Eslami (2018) A New Improved Gas Distributor Plate with Enhancing Properties for Hydrodynamics of Bubbling Fluidized Bed Gasifier. Doctoral thesis, Universiti Teknologi PETRONAS.

Agung Dewandaru, Agung (2008) A Map-matching Algorithm to Improve Vehicle Tracking Systems Accuracy. [Final Year Project] (Unpublished)

Ahamad Azahari, Ahmad Syahmi (2017) Grey Relational Analysis For Piping Systems Subject To Corrosion Under Insulation. [Final Year Project] (Submitted)

Ahmad, Asrul Nizar (2005) Remote control fFor PC / by Asrul Nizar Bin Ahmad, TJ 212 .I61 A111 2005. [Final Year Project]

Ahmad, Muhammad Najmie (2005) Utility-process interface optimization /by Muhammad Najmie Ahmad, TJ 153 .M952 2005. [Final Year Project]

Ahmad, Muhammad Syahmi (2014) Electromagnetic Windshield Wiper: Conceptual Study and Analysis. [Final Year Project] (Unpublished)

Ahmad, Muhd Amirulnizam (2004) Study on Effects of Surface Roughness Variations on Corrosion Resistance of Metal Components. [Final Year Project] (Unpublished)

Ahmad, Nurul Najat (2011) Study of the Microstructure of the Gas Turbine Internal Blade. [Final Year Project] (Unpublished)

Ahmad Abustaman, Mohd Zikri (2008) Processing of Alumina Powder into Ceramic Foam Materials by Impregnating Polyurethane Sponge with Bonded Ceramic Slurry. [Final Year Project] (Unpublished)

Ahmad Asri, Nur Alya Qistina (2022) Effect of Hybrid Composition and Volume Fraction on Microstructure and Micro-hardness of Aluminum Titanium Carbide (Al/TiC) via Friction Stir Processing. [Final Year Project] (Submitted)

Ahmad Damanhuri bin Sharipudin, Damanhuri (2008) New Design of Heat Spreader for Semiconductor Device. [Final Year Project] (Unpublished)

Ahmad Exsan bin Othman, Ahmad Exsan (2008) Study on various types of antirust to prevent corrosion on heat sink terminal. [Final Year Project] (Unpublished)

Ahmad Fadhil Hafiz Bin Mohd Ali, Ahmad Fadhil Hafiz (2008) The Enhancement of Micro Grinding Process By Using NdFeB To Seize Material Dust. [Final Year Project] (Unpublished)

Ahmad Fairus Bin Zamri, Ahmad Fairus (2008) Analysis of Jet Fire on Intumescent Coating Applied on Steel Substrate. [Final Year Project] (Unpublished)

Ahmad Farhan Iberahim, Ahmad Farhan (2010) Adaesogn Of Retractable Spread Breakers. [Final Year Project] (Unpublished)

Ahmad Fauzi, Marwan Asyraaf (2016) Synthetic Analysis Of Fluid Flow Through Particle Image Velocimetry (PIV). [Final Year Project] (Submitted)

Ahmad Fauzi, Muhamad Faiz Danial (2021) COMPUTATIONAL FLUID DYNAMIC (CFD) INVESTIGATION ON PERFORMANCE OF PARABOLIC TROUGH COLLECTOR (PTC) USING OIL BASED NANOFLUID. [Final Year Project] (Submitted)

Ahmad Firdaus bin Suhardi, Ahmad Firdaus (2010) Analysis of Compaction and Sintering of Compacted Silica Sand and Clay Mixture. [Final Year Project] (Unpublished)

Ahmad Hazwan bin Ahmad Hariri, Ahmad Hazwan (2010) Life Cycle Assessment of Thermal Storage System. [Final Year Project] (Unpublished)

Ahmad Helmi Mohd Amin, Ahmad Helmi (2010) Effects of Surface Roughness on the Adhesion and Corrosion Properties of Organic Coating Applied on One Surface of One Sample Set of Mild Steel. [Final Year Project] (Unpublished)

Ahmad Hidayat Bin Dahalam, Ahmad Hidayat (2008) Design and Fabrication of a Brush Cutter to Lawn Mower Conversion Kit. [Final Year Project] (Unpublished)

Ahmad Husaini Bin Bahaman, Ahmad Husaini (2012) Parametric Analysis of Flat Plate Solar Collector For Performance Evaluation. [Final Year Project] (Unpublished)

Ahmad Hussaini Bin Hamdan, Ahmad Hussaini (2010) Study and Analysis of Fabrication and Properties of Sand Lime Bricks. [Final Year Project] (Unpublished)

Ahmad Johari, Ahmad Abdullah (2004) Fiber Orientation In Short Fiber Reinforced Thermoplastic Composites. [Final Year Project] (Unpublished)

Ahmad Kamil, Muhammad Akmalhazwan (2012) MODELING INTERGRANULAR FRACTURE AT ELEVATED TEMPERATURE. [Final Year Project] (Unpublished)

Ahmad Khairuddin bin Ahmad Kamal, Ahmad Khairuddin (2008) CFD Simulation and Wind Tunnel Test of NACA 4412 Airfoil Wing Section at Different Angles of Attack. [Final Year Project] (Unpublished)

Ahmad Latphy, Ahmad Nazri bin (2009) Study on the Effects of Heat Transfer through Glass Walls on Cooling Load. [Final Year Project] (Unpublished)

Ahmad Lukman, Muhammad Amirul Asri (2011) Investigation of The Natural Convection Heat Transfer in Deep Wellbore. [Final Year Project] (Unpublished)

Ahmad Luqman Al-Hakim Bin Abd Malik, Ahmad Luqman Al-Hakim (2010) Analysis of a Pneumatic Artificial Muscle and Construction of a Model. [Final Year Project] (Unpublished)

Ahmad Nadim Bin Faisal, Ahmad Nadim (2010) Effect of Surface Roughness to the Adhesion Strength of Polyurea. [Final Year Project] (Unpublished)

Ahmad Nur Firdause Bin Zainal, Ahmad Nur Firdause (2008) Flow Analysis And Optimization Of A Manufacturing System Using Witness. Other thesis, Universiti Teknologi Petronas.

Ahmad Radzi, Ahmad Khalil (2011) Study on Wonn Defect in 6061 Aluminum Alloy Friction Stir Welded Plates. [Final Year Project] (Unpublished)

Ahmad Rafie bin Mohmad Tahir, Ahmad Rafie (2010) Design and Development of Ball Bearing for Inclined Loads. [Final Year Project] (Unpublished)

Ahmad Rassdi, Nurul Hidayah (2013) Cellulosic-Based Packaging Material from Corn Husk. [Final Year Project] (Unpublished)

Ahmad Redzuan, Ahmad Zhafran (2013) Development of Redundancy Model for Co-generation Plant. [Final Year Project] (Unpublished)

Ahmad Ruslan, Ahmad Ehsan (2008) Effect of Used Engine Oil to High Strength Microwave Incinerated Rice Husk Ash (MIRRA) Concrete. [Final Year Project] (Unpublished)

Ahmad Ruslan, Ahmad Ehsan (2008) Effect of Well Pattern to the Water Alternating Gas (WAG) Carbon Dioxide Injection on Angsi 1-35 Reservoir. [Final Year Project] (Unpublished)

Ahmad Sabri, Shahir (2011) Effect Of The Internal Fluid Flow In The Glass Fibre Reinforced Plastic (GFRP) Pipe Dynamic. [Final Year Project] (Unpublished)

Ahmad Sauki, Muhammad Muiz Haqimi (2014) Effects of Dolomite on Thermal Performance of Intumescent Fire Retardant Coating for Structural Steel. [Final Year Project] (Unpublished)

Ahmad Shahrom, Mohd Faiz (2009) Design and Development of Thermal Energy Storage (TES) Tank. [Final Year Project] (Unpublished)

Ahmad Soalahuddin Al-Thani, Adam Iman (2022) Effect of Types of Rubber on Thermal Properties of Magnetoactive Material. [Final Year Project] (Submitted)

Ahmad Sohimi, Amierul Fahmi (2012) Tensile and Flexural Properties of HDPE/PET/Kenaf Hybrid Composites. [Final Year Project] (Unpublished)

Ahmad Suhaimi Bin Sokiman, Ahmad Suhaimi (2010) Effects of Wall Temperature on the Viscoelastic Fluid Flow through Gradual Contraction. [Final Year Project] (Unpublished)

Ahmad Syafwan Bin Mohd Saidi, Ahmad Syafwan (2012) Thermal Management of Battery for Proton Green Mobility Car. [Final Year Project] (Unpublished)

Ahmad Syahidi Bin Che Zainal, Ahmad Syahidi (2008) An Experimental Study On The Wave Induced Instability Of Pipelines: The Breakout Of Pipelines. [Final Year Project] (Unpublished)

Ahmad Syazwan Bin Samsuddin, Ahmad Syazwan (2010) Void Content Analysis of a Polymer Composite Manufactured via Resin Infusion Process. [Final Year Project] (Unpublished)

Ahmad Tarmizi, Mohd Fairozlan (2008) Total Productive Maintenance Assessment on Discrete Manufacturing System. [Final Year Project] (Unpublished)

Ahmad Wazini Bin Ahmad Tajuddin, Ahmad Wazini (2010) Design of Interlocking for the Micro Unmanned Aerial Vehicle Vertical Take-Off and Landing Mechanism. [Final Year Project] (Unpublished)

Ahmad Yusof bin Nazlan, Ahmad Yusof (2010) The Design of an Autoguide System Prototyped for Conventional Vehicle on Highway. [Final Year Project] (Unpublished)

Ahmad Zahidin, Amirul Ariffin (2015) Demulsification of MIRI Crude Emulsion using Aeration. [Final Year Project] (Unpublished)

Ahmad Zamani Masnizam Bin Abdullah Zawawi, Ahmad Zamani Masnizam (2008) Study of the Effects of Flame Perturbation by High-Speed Schlieren Imaging. [Final Year Project] (Unpublished)

Ahmed, Umair (2017) DEVELOPMENT OF ROOT CAUSE FAILURE ANALYSIS FRAMEWORK FOR EQUIPMENT FAILURE ANALYSIS IN OIL AND GAS INDUSTRY. Masters thesis, Universiti Teknologi PETRONAS.

Aiman Bin Thalaha, Aiman (2010) Failure Analysis Of The Mechanical Seal Used In The Condensate Booster Pump At Onshore Slugcatcher (OSC). [Final Year Project] (Unpublished)

Aina Liyana Bt Abu Bakar, Aina Liyana (2010) Study on the Flow Characteristics of a Bluff Body Cut From a Square Cylinder. [Final Year Project] (Unpublished)

Ajid, Azlia (2008) Solar Powered Exhaust Fan for Automobiles. [Final Year Project] (Unpublished)

Akbar, Ahmad Radikal (2016) Parametric Analysis of Auto-reinforce Magnetic Flywheel as Regenerative Energy Storage for Automobile Engine. Masters thesis, Universiti Teknologi PETRONAS.

Al Batati, Nabil (2016) Simulation of Drill String Vibration due to Riser's Oscillation. Masters thesis, Universiti Teknologi PETRONAS.

Albarody, Thar M. Sadri (2012) DYNAMIC ANALYSIS OF LAMINA TED COMPOSITE MAGNETO-THERMO-ELECTRO-ELASTIC SHELL. PhD. thesis, Universiti Teknologi PETRONAS.

Alehan, Muhammad Nazree (2011) Study on Improvement of Cooling Energy and Thermal Comfort of Klinik Pergigian Batu Gajah. [Final Year Project] (Unpublished)

Alexander, Alan Arulandom (2015) Study of Sound Wave as a Flame Extinguisher. [Final Year Project] (Unpublished)

Ali, Aboubaker Abdalla Ibrahim (2013) Development of Fuel Briquettes from Biomass Residue. Masters thesis, Universiti Teknologi PETRONAS.

Ali, Fahmi (2008) Design and Analysis of Suspension System for a Formula SAE Race Car. [Final Year Project] (Unpublished)

Ali, Lina Fahimah (2016) Development of Excel Based Reliability Model to Estimate Life Distribution of Mechanical Seals. [Final Year Project] (Submitted)

Ali, Zain (2016) INVESTIGATION OF CONJUGATE HEAT TRANSFER OF A ROTATING LATENT HEAT ENERGY STORAGE. [Final Year Project] (Submitted)

Ali Ameen Roshan Ali, Ali Ameen (2023) Development of Porosity Evaluation of Inservice Thermal Barrier Coated Ceramics Using X-Band Microwave Nondestructive Technique. Masters thesis, Universiti Teknologi PETRONAS.

Alias, Mohd Amirul Mukminin (2011) Study of Adhesive Strength in Polymer Plate Heat and Mass Exchanger. [Final Year Project] (Unpublished)

Alias, Mohd Hazrul Azam (2011) Design of a Powertrain System for Simple Vehicle. [Final Year Project] (Unpublished)

Alias, Muhammad Farhan (2014) Modeling and Control of Axial and Torsional Stick-Slip Oscillations in Drill String. [Final Year Project] (Unpublished)

Alif Aiman bin Ahmad Othman, Alif Aiman (2009) Design of Robot Gripper Mechanism for ROBOCON Robot Competition. [Final Year Project] (Unpublished)

Aliff Amirul Hamzah Bin Adenan, Aliff Amirul Hamzah (2012) Reverse Engineering for Analysis and Design Improvement of Ball Valve Seat. [Final Year Project] (Unpublished)

Aliya Binti Muhamad, Aliya (2010) The Effect of Expandable Graphite and Zinc Borate on Performance of Intumescent Fire Retardant Coating. [Final Year Project] (Unpublished)

Alkali, Adamu Umar (2016) Machiniability Study of Thermal Enhanced Machining of 316L Stainless Steel using Oxyacetylene Flame. Doctoral thesis, Universiti Teknologi PETRONAS.

Aman Zaharil, Muhammad Hafiz Osman (2016) Experimental Modeling and Evaluation of Solar Cooker For Malaysia Potential. [Final Year Project] (Submitted)

Amar Rahimi Bin Ishak, Amar Rahimi (2010) Development of Tronoh Silica Sand Fine Particles Production: Dry and Wet Milling Approaches. [Final Year Project] (Unpublished)

Amat, Arif Danial (2016) Cold-Flow CFD Analysis of Intake-Compression process for Hydrogen-Fuelled Internal Combustion Engine. [Final Year Project] (Submitted)

Amer, Mohamad Izat Fikri (2015) Gas-Liquid Separation in T-Junction. [Final Year Project] (Unpublished)

Americo, Paulo Faife Inocencio (2020) Numerical Investigation of PDC Cutter – Rock Interaction using LS-DYNA and Design of Experiment. [Final Year Project] (Submitted)

Ami Ardi, Muhamad Afiq Affandi (2021) INVESTIGATIONS OF MECHANICAL PROPERTIES AND MICROSTRUCTURE ANALYSIS OF AL 7075 GNP’S COMPOSITES. [Final Year Project] (Submitted)

Ami Ardi, Muhamad Afiq Affandi (2021) INVESTIGATIONS OF MECHANICAL PROPERTIES AND MICROSTRUCTURE ANALYSIS OF AL 7075 GNP’S COMPOSITES. [Final Year Project] (Submitted)

Aminah Syahidah Bt Mohd Yusuff, Aminah Syahidah (2011) Study on the Effect of Thermal Stability of Corrosion Inhibitor. [Final Year Project] (Unpublished)

Aminuddin, Ahmad Syahiq (2015) Design and Fabrication of Automatic Welding Manipulator for Oil and Gas Pipeline Welding. [Final Year Project] (Unpublished)

Aminuddin, Ikhwan Syamim (2016) Investigation of Mechanical properties of Nitrided Weldments of Austenitic Stainless Steel After Quenching. [Final Year Project] (Submitted)

Aminudin, Ahmad Shakir (2011) Burst pressure estimation of corroded pipeline with interacting defects using FEA. [Final Year Project] (Unpublished)

Aminudin, Muhammad Syahmi (2013) Analysis of Carbon Dioxide (CO2) Emission by Heat Recovery Steam Generator (HRSG). [Final Year Project] (Unpublished)

Amir, Norlaili (2013) Development of Fibres Reinforced Intumescent Coatings for Mild Steel Structures. Doctoral thesis, Universiti Teknologi PETRONAS.

Amir Abdullah, Adam Muhsein (2014) Experimental Study of Micro-Explosion Phenomena of Emulsified Fuel. [Final Year Project] (Unpublished)

Amir Afiz Bin Mohamed Nizan, Amir Afiz (2008) Human Transporter(E-Porter). [Final Year Project] (Unpublished)

Amir Ainulariff bin Mahmud, Amir Ainulariff (2010) Implementation of Crack Opening Displacement and Compliance Methods In Fatigue Crack Growth Tests. [Final Year Project] (Unpublished)

Amir Hossein Ghanizadeh, Amir Hossein (2009) Analysis of Gas Turbine Blade Cooling System. [Final Year Project] (Unpublished)

Amirrudin, Muhammad Munzir (2011) Effects of Sa 2 and Sa 2.5 Blast Cleaning Surface Preparation on the Adhesion and Corrosion Protection Properties of Coating. [Final Year Project] (Unpublished)

Amiruddin, Ahmad Yusuf (2018) CFD Investigation of General Electric Gas Turbine Wash Nozzle. [Final Year Project] (Submitted)

Amirul Asyraf Bin Amiruddin, Amirul Asyraf (2010) Stress Analysis on Four Battered-Legs Offshore Jacket Structures. [Final Year Project] (Unpublished)

Ammar Bin Azhar, Ammar (2008) Design Of A Finger Trainer Prototype For Paralyzed/Stroke Patients. [Final Year Project] (Unpublished)

Ampuani@Azmei, Muhammad Redha (2015) DESIGN, FABRICATION, AND EXPERIMENTAL STUDY OF THE PERFORMANCE OF THERMOELECTRIC MODULES FOR COOLING OF A SINGLE ROOM TEST HOUSE. [Final Year Project] (Unpublished)

Amran, Mohd Hafiz (2008) Investigation On Savonius Wind Turbine In Directed Flow. [Final Year Project] (Unpublished)

Anak Biga, Blythe Kollias (2016) Characterization of Restart Pressure in Production Pipeline for Waxy Crude Oil as A Result of Injection of Non-Reacting Gas. [Final Year Project] (Submitted)

Anak Richard, Angel (2016) Quality Characterization of the Vacuum-Bagging-Only (VBO) – Out Of Autoclave (OOA) Cured Composite Panels. [Final Year Project] (Submitted)

Anas, Atika Illyani (2011) Study on Removal of Particles from Used Turbine Oil. [Final Year Project] (Unpublished)

Anas Hakimi bin Kori, Anas Hakimi (2010) Three Dimensional Stress Analysis in a Steam Turbine Blade. [Final Year Project] (Unpublished)

Anggara Warsita, Anggara Warsita (2012) A Study on Extension of Useful Annular Area of a Swirling Fluidized Bed Distributor. [Final Year Project] (Unpublished)

Anis Rafie bin Ahmat Rmadani, Anis Rafie (2008) Repeating Weld Repair’s Effect on Microstructure and Mechanical Properties of Weld Metal. [Final Year Project] (Unpublished)

Annaorazov Rejep, Annaorazov (2010) Fundamental Study of Sprays of Different Fluids. [Final Year Project] (Unpublished)

Anthony Aga, Erizeanne (2012) Design and Development of Underwater Glider. [Final Year Project] (Unpublished)

Anuar, Ahmad Naufal (2016) Analysis of Wheel Rolling Resistance in a Personal Electric Vehicle. [Final Year Project] (Submitted)

Anuar, Nor Hazwani (2013) Physical Properties of Rice Husk Packaging Material. [Final Year Project] (Unpublished)

Anuar bin Ahmad, Anuar (2010) Thermal Stress Distribution in the Drum Brake of a Small Vehicle. [Final Year Project] (Unpublished)

Anwarudin, Saidu Mohamed (2004) Design and Development of a "Two- Axis Leveling Platform". [Final Year Project] (Unpublished)

Arafat Mahdy, Amr Essam (2016) Investigation on The Effect of Drill Diameter During Bone Drilling for Surgery Applications. [Final Year Project] (Submitted)

Arif Zaki Bin Ariffin, Arif Zaki (2012) Development of Heat Exchangers Design Tool. [Final Year Project] (Unpublished)

Arifin, Mohd Nurhadi (2008) The Investigation i11to Tribological Properties of Carbon Fiber Reinforced Composite. [Final Year Project] (Unpublished)

Armando Macuacua, Florivaldo Daniel (2020) CFD Optimization Of Building Glazed Cladding In Order To Achieve Thermal Comfort And Achieve Energy Saving. [Final Year Project] (Submitted)

Armo, Dinish Kumar (2016) Experimental Study of Chloride Stress Corrosion Cracking In Stainless Steel. [Final Year Project] (Submitted)

Arob Deng Chol, Michael (2008) Study of Stick-slip torsional vibration in Drilling Operation. [Final Year Project] (Unpublished)

Arshad, Haroon (2020) Experimental Study on Performance of Microwave-metal Interaction Pyrolysis of Plastics. Doctoral thesis, Universiti Teknologi PETRONAS.

Arthit Saengchot A/L Chali, Arthit (2011) Prediction of Remaining Useful Life for Service-Exposed Industrial Turbine Blade. [Final Year Project] (Unpublished)

Asba Madzidah binti Abu Bakar, Asba Madzidah (2010) Performance of Polyurea Coating Under Water Immersion at High Temperature. [Final Year Project] (Unpublished)

Ashfaq Ghafran bin Abdul Rahman, Ashfaq Ghafran (2010) Evaluation of the Transient Response of a Servo Motor Using MATLAB/Simulink. [Final Year Project] (Unpublished)

Aslam, Muhammad Aslam (2016) Powder Injection Modeling of Modified 316L Stainless Steel for Dental Implant Application. Doctoral thesis, Universiti Teknologi PETRONAS.

Asli, Shahrandin (2005) Power flow solution by using matlab / by Shahrandin Bin Asli, TJ 153 .S524 2005. [Final Year Project]

Asmawi Bin Sha’ari, Asmawi (2008) Simulation Of Sintering In Powder Metallurgy Application For Ferrous Materials. [Final Year Project] (Unpublished)

Asrul Hakim, Amira Nurhaliza (2022) Study On the Types of Petroleum-based Oil and Its Impact on Tensile Properties of MRE composite. [Final Year Project] (Submitted)

Awalludin, Azlan (2017) Electrodeposition and Characterization of Ni-Mo-ZrO2 Composite Coatings. [Final Year Project] (Submitted)

Awalludin, Azlan (2017) Electrodeposition and Characterization of Ni-Mo-ZrO2 Composite Coatings. [Final Year Project]

Awang, Norhazini (2011) The comparison between C02/NH3 and C0~1234yf for optimal condensing temperature in cascade refrigeration systems. [Final Year Project] (Unpublished)

Awang Besar, Erfan Ruzalfian (2013) Development of Conceptual Design Support System for Mechanisms. [Final Year Project] (Unpublished)

Awang Nazarudin, Awang Muhammad Nasuha (2014) Framework of a Bow-Tie Based Quantitative Risk Assessment on an Offshore Oil and Gas Processing Unit. [Final Year Project] (Unpublished)

Ayob, Mohamad Firdaus (2008) Investigation into the Potential ofBio-based Automotive Engine Lnbrieation Oil Using Tribologieal Test Method. [Final Year Project] (Unpublished)

Ayoub, Abi Aiman (2011) A Study of Energy Recovery Potential from Domestic Sewage Sludge. [Final Year Project] (Unpublished)

Azahariman Bin Azazian, Azahariman (2008) The Effects of Multiple-Use of Polyethylene Terephthalate (PET) Bottles on Antimony Concentration. [Final Year Project] (Unpublished)

Azami, Adam Hazman (2018) Evaluation of Effective Current Output for Sacrificial Anodes at Various Sea Water Depth. [Final Year Project] (Submitted)

Azan, Nur Syafiqah (2014) Feasibility Studies and Analysis to turn Raw Sand Dust into Construction Material with The Addition of Calcium Carbonate as a Melting Catalyst. [Final Year Project] (Unpublished)

Azarol Nazwi, Azril Aiman (2021) Feasibility of Single Barrel Heave Compensator 5MT. [Final Year Project] (Submitted)

Azazian, Azahariman (2008) The Effects of Multiple-Use of Polyethylene Terephthalate (PET) Bottles on Antimony Concentration. [Final Year Project] (Unpublished)

Azemi, Mohd Aziman (2008) Failure Analysis of Heat Exchanger's Tubes at GPP Kerteh. [Final Year Project] (Unpublished)

Azhar, Muhamad Hanif Muqsit (2014) Optimum Lay-Up Design Analysis of Basalt Fiber Reinforced Composite Using Finite Element Analysis (FEA). [Final Year Project] (Unpublished)

Azhar, Muhammad Afieq Zakwan (2014) Heat Transfer of Combustion Chamber Wall of a Diesel Engine. [Final Year Project] (Unpublished)

Aziz, Hammad Aziz (2015) Development of Metal-Oxide Fillers Reinforced Intumescent Fire Retardant Coating for Structural Applications. Masters thesis, Universiti Teknologi PETRONAS.

Aziz, Azman (2008) Design and Analysis of a Disc Rotor for a Small Race Car's Braking System. [Final Year Project] (Unpublished)

Aziz, Hisyam Juwaidi (2014) Design Support System for Pressure Vessel Design. [Final Year Project] (Unpublished)

Aziz Al-Wakeel, Haitham Behnam (2016) Investigation on Localized Rapid Soot Oxidation using Metal-Assisted High Frequency Electromagnetic Heating. Doctoral thesis, Universiti Teknologi PETRONAS.

Azizan, Azuan (2005) Autonomus Vehicle / by Azuan Azizan, UG 615 .A111 2005. [Final Year Project]

Azizan B Kamarudin@Mohd Ramly, Azizan @Mohd Ramly (2009) Study the Dynamic Behavior of Elevated Temperature Micro-Bubbles in a Purification System. [Final Year Project] (Unpublished)

Azizdin, Amirul Iman Bin (2009) Stress Corrosion Cracking on Welding of Offshore Structure. [Final Year Project] (Unpublished)

Azizuddin, Aliah Azlin (2016) DEVELOPMENT OF THERMAL INSULATION BY UTILIZNG EMPTY FRUIT BUNCH (EFB). [Final Year Project]

Azlan, Uzair Aslam (2013) Solar Passive Cooling: Solar Chimney for Natural Ventilation. [Final Year Project] (Unpublished)

Azlan Bin Mohamed Adnan, Azlan (2008) Computer Aided Reverse Engineering with Renishaw Digitizer for Digitization and Mazak for Model Fabrication. [Final Year Project] (Unpublished)

Azliza Binti Ishak, Azliza (2010) Microstructural Characterization Of Polymer Plate Washer Produce By A Novel Technique. [Final Year Project] (Unpublished)

Azmal Khuzairi Bin Abdul Wahab, Azmal Khuzairi (2010) Investigation into the Abrasion Resistance of Polyurea Coating by the Taber Abraser. [Final Year Project] (Unpublished)

Azman, Muhammad Afif (2022) The Effects of Particle Size Of Zirconia-Alumina Powders On The Mechanical Properties of Thermal Barrier Coating Developed by High Velocity Oxy Fuel. [Final Year Project] (Submitted)

Azman, Ahmad Imran (2016) CORROSION INHIBITION PERFORMANCE BY OCTYLMETHYLIMIDAZOLIUM- BROMIDE OMIBr ON API 5L X52 STEEL IN 1.0M H2SO4. [Final Year Project] (Submitted)

Azman, Athira (2013) The Effect Of Voltage To Welded Aluminum And Steel By Using Gas Metal Arc Welding (GMAW). [Final Year Project] (Unpublished)

Azman, Muhamad Fahmi (2015) Development of Optimal Design Support System for Beam Structure. [Final Year Project] (Unpublished)

Azman, Muhammad Khalil (2012) Tensile and Flexural Properties of HDPE/Kenaf Composites with & without Compatibilizer. [Final Year Project] (Unpublished)

Azman, Usamah (2013) Analysis of Whirl Speed of Rotor-bearing System Supported on Fluid Film Bearing. [Final Year Project] (Unpublished)

Azman Bin Daud, Azman (2010) A Study Of Solar Chimney Performance Using Fluent Software. [Final Year Project] (Unpublished)

Azme, Amirul Farhan (2022) Study On the Influence of Particle Content on Tensile Properties of Smart Rubber Composite. [Final Year Project] (Submitted)

Azmei, Wan Sofia (2016) Characteristics Study of Biomass Fuel from Poultry Waste using Thermogravimetric Analysis. [Final Year Project] (Submitted)

Azmi, Maziah (2022) Estimating Generalized Renewal Process (GRP) Model Parameters for Repairable Systems using Monte Carlo Approach. [Final Year Project] (Submitted)

Azmi, Fasyiha Aida (2011) STUDY OF WEAR BEHAVIUR AND COATING QUALITY OF ZINC AND CHROMIUM METALLIC COATING ON MILD STEEL SUBSTRATE. [Final Year Project] (Unpublished)

Azmi, Muhammad Hassanei Heykal (2014) Effect of Drilling Mud Contamination on the Properties of Waxy Crude Oil. [Final Year Project] (Unpublished)

Azmin, Muhammad Danial (2020) CFD ANALYSIS OF MODIFIED IMPELLER FOR PAINT MIXER. [Final Year Project] (Submitted)

Azreel Zairee Bin Omar, Azreel Zairee (2012) Energy Recovery Studies For Flare Systems in Offshore Oil and Gas Facilities. [Final Year Project] (Unpublished)

Azri Izwan Bin Mazlan, Azri Izwan (2008) Characterization and Properties of Copper and Carbon Powders Mixture. [Final Year Project] (Unpublished)

Azrul Nizam Bin Othman, Azrul Nizam (2008) To Design and Develop Fe-Cu-C Alloying Suitable for Self Lubricating Bearing through Powder Metallurgy (P/M) Technique. [Final Year Project] (Unpublished)

a/l Asokan, Arravinthan (2016) Mechanical Properties and Performance Evaluation of Polypropylene (PP)/Lalang Grass Composite. [Final Year Project] (Submitted)

a/l Gurdial Singh, Dalvinder Singh (2016) Performance Analysis of Ice Crystals Collection Mechanism in a Freezing Desalination Process. [Final Year Project] (Submitted)

a/l Jeyaprakasam, Gajendran (2016) Study of Free Falling Particle in Viscous Fluid. [Final Year Project] (Submitted)

a/l N.Rajandran, Vinod (2016) New innovative methodology concept for Product Development Process. [Final Year Project] (Submitted)

B

BAHARUDDIN, AHMAD AIDIL AIZAT (2020) PERFORMANCE OPTIMIZATION OF A ROOF TOP TRANSVERSE AXIS WIND TURBINE. [Final Year Project] (Submitted)

BAIG, ZEESHAN (2018) Development and Characterization of Graphene Nanoplatelets Reinforced Aluminum Nanocomposites. PhD. thesis, Universiti Teknologi PETRONAS.

BEHESHTI, MOHAMMADALI (2020) The electrochemical carbon dioxide conversion to Synthesis Gas (SYNGAS) by ZincNickel bimetallic electrocatalysts. PhD. thesis, Universiti Teknologi PETRONAS.

BIN JAMAL, AJMAL FALIQ (2012) STUDY OF COMPARISON IN CORROSION RESISTANCE OF FRICTION STIR WELDING ALUMINUM ALLOY (AA6061 AND AA1100). [Final Year Project] (Unpublished)

BOURIAABADI, MOHAMMADREZA TAHAN (2017) Application of Adaptive Neuro-fuzzy inference System in Performance-based Condition Monitoring of Industrial Gas Turbines. PhD. thesis, Universiti Teknologi PETRONAS.

BRONTO AGUNG, ASKAR TRIWIY ANTO (2013) SURFACE CHARACTERISTICS OF STAINLESS STEEL AISI 3 I 6L AFTER LOW TEMPERATURE HYBRID THERMOCHEMICAL TREATMENT. PhD. thesis, UTP.

BURHANI, NURUL RAWAIDA AIN (2018) TEMPERATURE VARIATION IN APPLICATION OF ARTIFICIAL NEURAL NETWORK FOR PREDICTION OF CORROSION RATE UNDER INSULATION. PhD. thesis, Universiti Teknologi PETRONAS.

Babiker, Hussam Eldin Salah Abuelnour (2014) Computational Fluid Dynamics Modeling Of Smoke Spread Due To Fire in Buildings. [Final Year Project] (Unpublished)

Babiker Adam, Mohammed Elamen (2018) Data Palm Seeds For Power Generation: Thermochemical conversion analysis of a gasifier-engine system. PhD. thesis, Universiti Teknologi PETRONAS.

Badrol Hisham, Muhammad Nadzmi Faez (2017) A Techno-Economic Investigation of a Residential Solar Photovoltaic System at Bandar Universiti, Perak, Malaysia. [Final Year Project] (Submitted)

Bah, Sea Min (2008) Design and Fabricate a Lab Scale Cross Flow Water Turbine. Other thesis, Universiti Teknologi Petronas.

Baharuddin, Asfahani Binti (2009) Design of Aeration System for the Lake Surrounding An Nur Mosque. [Final Year Project] (Unpublished)

Baharum, Zulhazli (2004) Aerodynamic Analysis of External Flow for Hybrid Electric Vehicle (HEV). [Final Year Project] (Unpublished)

Bahtiar, Muhammad Aiman (2016) Nano Polishing of Titanium Alloy with Ionic Liquid. [Final Year Project] (Submitted)

Balachandran, Mokhan (2021) Thermal Comfort Study of a Building Equipped with Nanofluid Assisted Thermoelectric Air Conditioner for the Hot Humid Climate of Malaysia. [Final Year Project] (Submitted)

Balqis Binti Subki, Balqis (2008) Lighting Energy Audit in New Academic Buildings of Universiti Teknologi PETRONAS. [Final Year Project] (Unpublished)

Basharuddin, Muhammad Syahir (2011) Nitriding of X-52 Carbon Steel: Mechanical Characterization. [Final Year Project] (Unpublished)

Bashiri, Robabeh (2016) Development of Tandem Solar Cell with Cu-Ni/TiO2 Photocatalyst for Hydrogen Production. Doctoral thesis, Universiti Teknologi PETRONAS.

Basir, Muhammad Hisyamuddin (2015) Risk-Based Inspection Model for Heat Exchanger Tube Bundles. [Final Year Project] (Unpublished)

Baskaran, Prasanth Raj (2016) Experimental Study on Effects of Welding Parameters on Microstructure & Mechanical Properties of AA6061-T6 Material Joined by Friction Stir Welding (FSW). [Final Year Project] (Submitted)

Besar, Mohd Firdaus (2008) COz Corrosion Stndy by Electrochemical Impedance Spectroscopy (EIS) and Linear Polarization Resistance (LPR). [Final Year Project] (Unpublished)

Bhaskoro, Petrus Trio (2017) Viscosity Prediction for Waxy Crude Oil - Effects of Physico-Chemical Parameters. Doctoral thesis, Universiti Teknologi PETRONAS.

Bhayo, Bilawal Ahmed (2016) Experimental Investigation of S-rotors for Stand-alone Wind Power Applications. Masters thesis, Universiti Teknologi PETRONAS.

Bin Wahabi, Mohd Tarmizi (2014) Effects of Titanium Addition on Mechanical and Corrosion properties of 316L Stainless Steel Developed through Powder Injection Molding Process. [Final Year Project] (Unpublished)

Bistamam, Nurfarah Liyana (2015) Investigation of Carbon Black Production from Waste Tyre Burning. [Final Year Project] (Unpublished)

Bong, David (2013) Development of Thermoelectric Generator (TEG) For Energy Recovery in Perodua Myvi. [Final Year Project] (Unpublished)

Boon, Tan Han (2016) CFD Comparative Study of 3-D Compressible Flow Over Seamless and Canard Aerodynamic Flying Bodies. [Final Year Project] (Submitted)

C

CHANDERENG, NAWIIN (2021) Development and Characterization of Carbon Quantum Dots from Green Synthesis Route for Potential Supercapacitor Application. [Final Year Project] (Submitted)

CHANG, YEE JIAN (2017) STUDY ON THE EFFECTIVENESS OF INORGANIC CORROSION INHIBITOR FOR MILD STEEL IN COOLING WATER SYSTEM. [Final Year Project]

CHE A. HALIM, FAHMI (2013) Characterization of Double-sided Friction Stir Welding (FSW). [Final Year Project] (Unpublished)

CHE BAHARUM, CHE MOHD HASHRUL (2011) CHARACTERIZATION OF WASTE FROM THE PETROCHEMICAL INDUSTRY. [Final Year Project] (Unpublished)

CHE MANSHOR, MAGHF ARAH (2008) Design and Development of mould of UTP souvenir photo frame using Rapid Prototyping and Rapid Tooling technique. [Final Year Project] (Unpublished)

CHELLIAH, EDWIN RAKESH (2018) PERFORMANCE INVESTIGATION OF A THERMOELECTRIC COOLING SYSTEM FOR BUILDINGS. [Final Year Project] (Submitted)

CHENG WYEI YEE, SHARON (2017) THE EFFECT OF DRILLING DIAMETER AND CUTTING SPEED ON THE MACHINABILITY DURING DRILLING MAGNESIUM ALLOYS. [Final Year Project]

CHEONG, WILLIES Y.D (2016) Thermal Efficiency Study of the Combustion Chamber Designed for Small Scale Gas Turbine Engine Transformed from Turbocharger. [Final Year Project] (Submitted)

CHIN, ADAM REDUAN (2021) PORE-SCALE MODELLING OF FLOW BOILING HEAT TRANSFER IN METAL FOAM HEAT EXCHANGER. [Final Year Project] (Submitted)

CHONG, YEW POR (2013) INVESTIGATION ON THE EFFECT OF THE CHIMNEY CUP ON THE NATURAL UPWARD DRAFTING. [Final Year Project] (Unpublished)

CHOU, CHOONG YOU (2018) TECHNO-ECONOMIC ANALYSIS OF SOLAR FLAT-PLATE COLLECTOR WORKING WITH NANOFLUID. [Final Year Project] (Submitted)

Cassim, Sameer (2011) Design of a Multi-Staged Swirling Fluidized Bed. [Final Year Project] (Unpublished)

Chai, Tan Huat (2016) Root Cause Failure Analysis (RCFA) Root Causes Categorization and Generation of Recommended Data for RCFA Investigation. [Final Year Project] (Submitted)

Chai , Set Lee (2008) Use of Magnetic Field in Paraffin Wax Deposition Control for Surface Facilities. [Final Year Project] (Unpublished)

Chala, Girma Tadesse (2016) The Formation of Gas Voids in Waxy Crude Oil with Thermal Shrinkage. Doctoral thesis, Universiti Teknologi PETRONAS.

Chan, Wei Shin (2011) Experimental Characterization of Solid Biomass-Coal Mixture Combustion. [Final Year Project] (Unpublished)

Chan, Yen Pinng (2011) A Thermodynamics Study for a Mixture of Natural Gas & Water Flowing Through a Supersonic Nozzle. [Final Year Project] (Unpublished)

Chandrashakeran, Dharmesh Kumar (2020) The Influence of Oxidizing Parameters on the Formation of Oxide Layer as a Precursor for the Fabrication of Carbon Fiber-Steel Laminate. [Final Year Project] (Submitted)

Che Ali, Mohd Syafuddin (2005) Robust cascade control system for a heat exchanger plant / by Mohd Syafuddin Bin Che Ali, TJ 223 .T4 M697 2005. [Final Year Project]

Che Aslan, Nasrul Haziq (2017) MECHANICAL PROPERTIES AND PERFORMANCE EVALUATION OF RECYCLED POLYPROPYLENE AND TREATED MENGKUANG LEAVES COMPOSITES. [Final Year Project]

Che E Zwan bin Che Asaari , Che E Zwan (2010) Numerical Study on Influence of. [Final Year Project] (Unpublished)

Che Engku Chik, Che Engku Mohd Khairi (2016) Towards Zero - Energy Commercial Offices by Utilizing Phase-Change Energy Storage Heat Exchanger to Replace Conventional Air Conditioning System. [Final Year Project] (Submitted)

Che Ghazali, Mohd Atiqullah (2011) Study on Drilling Fluid Using Electrical Capacitance Tomography (ECT). [Final Year Project] (Unpublished)

Che Kamaruddin, Ahmad Hasnulnaim (2011) Effect of Energy Recovery on the Hoisting Crane Adapting Closed Loop Hydraulic Hoisting System. [Final Year Project] (Unpublished)

Che Ku Amran, Che Ku Hariz (2017) Design and MATLAB Simulation of Pitch Motion System Controller for Underwater Vehicle. [Final Year Project]

Che Suliman, Muhammad Syahmie (2016) RESIDUAL STRENGTH ANALYSIS OF CORRODED PIPELINE WITH INTERACTING DEFECTS SUBJECTED TO INTERNAL PRESSURE AND LONGITUDINAL COMPRESSIVE STRESS. [Final Year Project] (Submitted)

Che Wan Zaiki, Che Wan Juwairiah (2015) Experimental Study of Renewable Energy for Solar Parking in Universiti Teknologi PETRONAS (UTP). [Final Year Project] (Unpublished)

Cheah , Yuen Hung (2021) Experimental Study of the Influences of Temperature and Thermal Insulation on Stress Corrosion Cracking using 3-point bend test. [Final Year Project] (Submitted)

Chen , Tien Hao (2020) COMPUTATIONAL SIMULATION OF ENGINE COOLING SYSTEM PERFORMANCE OF A COMMERCIAL CAR. [Final Year Project] (Submitted)

Chen Ming Hui, Chen (2012) Effects of Additives on the Performance of Drag Reduction Agents. [Final Year Project] (Unpublished)

Cheng Lee Chon, Cheng Lee Chon (2012) GEOMECHANICS RELIABILITY MODELING FOR DE-RISKING. [Final Year Project] (Unpublished)

Chi, Yew Lih (2016) Characterization and Properties of Powder Metallurgy Alumina-Iron and Alumina-Copper Ceramic Composites. [Final Year Project] (Submitted)

Chian, Cheah Zi (2016) Implementation and Justification of Innovated Three Lines Loop for Single and Multi- Phase Flows Studies. [Final Year Project] (Submitted)

Chin, Eileen Wong Wee (2016) A Study on the Fatigue Assessment of Offshore Steel Catenary Riser. [Final Year Project] (Submitted)

Chin Swee Miin, Chin Swee Miin (2012) Investigation of Particle Motion in a Swirling Fluidized Bed using Particle Imaging Velocimetry. [Final Year Project] (Unpublished)

Choi , Y ee Xiong (2013) A Study on the Effect of Steam Leakage to the Heat Rate of Steam Power Plant. [Final Year Project] (Unpublished)

Chong , Wei Kit (2009) Design and Fabrication of Solar Collector Enhanced by Paraffin as Phase Change Medium. [Final Year Project] (Unpublished)

Choon Lin, Voon (2011) Environmental Impact of Gas District Cooling: A Case Study of a Small Cogeneration Plant. [Final Year Project] (Unpublished)

Choong, Weng Hong (2015) Effect of Tool Pin Profiles on the Weldment of AA6061-T6 Friction Stir Welded Plate. [Final Year Project] (Unpublished)

Chow , Xuan Hui (2015) Quasi Static Axial Loading on Carbon fiber wind to HDPE Composite Pipe (CFWHCP). [Final Year Project] (Unpublished)

Christine Engelbert, Christine (2011) Study on Heat Treatment Effect on Corrosion of API 5L X52 steel in CO2 Environment. [Final Year Project] (Unpublished)

Chua, Han Jim (2009) Development of Hybrid Solar Chimney. [Final Year Project] (Unpublished)

Chua , Ken Seng (2010) Design of a Glass Wall Cleaning Mechanism. [Final Year Project] (Unpublished)

Chung Yang, Nigel Chuah (2016) Investigating the Effect of Drilling Parameters and Mud Rheology for the Flow of Yield Power Law Fluid through Annulus. [Final Year Project] (Submitted)

Chuok, Gan Yee (2020) The Effect of Welding Parameters Between Titanium Alloy and Stainless Steel with Interlayer of Aluminium Alloy in Resistance Spot Welding. [Final Year Project] (Submitted)

Churn, Tey Chee (2014) Optimization of 4-Cylinder Spark Ignition Engine for Fuel Consumption and Vehicle Performance through Cylinder Deactivation and Forced Induction. [Final Year Project] (Unpublished)

Claudius, Rick Raynold (2013) Fatigue Crack Initiation and Propagation on Nitrided Ferritic Surfaces in Stainless Steel 439. [Final Year Project] (Unpublished)

Crist Ting, May Yie (2021) Microstructural and Mechanical Behaviour of Powder Metallurgy Processed TiC Reinforced Al7075-Based Composites. [Final Year Project] (Submitted)

D

DAHAN, MUHAMMAD FARHAN (2013) Frictional Contact Stress Analysis of Involute Spur Gear by Finite Element Method. [Final Year Project] (Unpublished)

DALHA, IBRAHIM BABANGIDA (2021) EXPERIMENTAL INVESTIGATION AND OPTIMIZATION OF SYNTHETIC BIOGAS INTAKE AND MIXING REGIMES IN DUAL-FUEL RCCI COMBUSTION. Doctoral thesis, UNSPECIFIED.

DAN, NSIKAN ETIM (2019) LOW TEMPERATURE NITRIDING OF DUPLEX STAINLESS STEEL TO INFLUENEC THE COMPOSITION ON CORROSION AND WEAR PROPERTIES. PhD. thesis, Universiti Teknologi PETRONAS.

DAUDA MUHAMMAD, IBRAHIM (2015) NON-LINEAR FINITE ELEMENT MODELING OF MECHANICAL BEHAVIOR OF SINGLE-WALLED CUBIC ZIRCONIA NANOTUBES. PhD. thesis, Universiti Teknologi PETRONAS.

DEGEN, TEE (2017) INVESTIGATION OF WATER-IN-BIODIESEL EMULSION CHARACTERISTICS PRODUCED BY ULTRASONIC HOMOGENIZER. [Final Year Project]

DHAMIN MOKHLIF, NASSIR (2013) MODELLING OF WAX CRYSTALLIZATION IN SOLVENT DEWAXING SCRAPED SURFACE EXCHANGERS AND CHILLERS. PhD. thesis, Universiti Teknologi PETRONAS.

DHARMANANDA, ROSHEN (2022) Open Hole Compression Performance of 3D Fiber Reinforced Composites. [Final Year Project] (Submitted)

DJALILOV, FARRUH (2017) MECHANICAL PROPERTIES OF RECYCLED HIGH DENSITY POLYETHYLENE REINFORCED WITH KENAF FIBERS. [Final Year Project] (Submitted)

DONG, WEE TIAT (2011) Extended Numerical Analysis on Gas Turbine Blade Cooling. [Final Year Project] (Unpublished)

DZULHIKAM, DZULAISAR (2021) EFFECTS OF AMPLITUDES OF EXTERNAL MECHANICAL EXCITATION ON VIBRATION RESPONSE OF PIPING SYSTEM. [Final Year Project] (Submitted)

Dams, Mohd Ridhuan (2009) DESIGNING AND SIMULATE AN ACTIVE PID CONTROLLER FOR A VEIDCLE SUSPENSION SYSTEM VIA CONTROLLABLE DAMPING DEVICES. [Final Year Project] (Unpublished)

Danial, Hassan (2016) Study On Reduction In Heat Transfer From The Turbine To Compressor In A Turbocharger. [Final Year Project] (Submitted)

Daran, Vivegan Murali (2017) Analysis Of Multiple Hole Structures Of Basalt Epoxy Laminates. [Final Year Project]

Daud, Amalina (2011) Modeling and Analysis of Dry Low Emission Combustor Discharge Nozzle Material & Structure for Rolls Royce Industrial RB211 Gas Turbine. [Final Year Project] (Unpublished)

Daud, Mohd Hafizudin (2011) Comparative Study of Spray of Different Liquids. [Final Year Project] (Unpublished)

Davis, Michael Tristan (2020) Experimental Investigation on Wire Rope Isolators. [Final Year Project] (Submitted)

Dayang Farhana Syafiah Binti Abang Usop, Dayang Farhana (2011) The Effects of Recycled Polypropylene/Wood Flour (r-PP/WF) Composites with and without Coupling Agent on Mechanical Properties. [Final Year Project] (Unpublished)

Dayang Fittri Noorkhairunnisa, Dayang Fittri Noorkhairunnisa (2010) Modification and Evaluation of Water Turbine for Power Generation. [Final Year Project] (Unpublished)

Declan Lim, Hong Chwen (2022) Numerical Modelling of Cooling System for Battery Electric Vehicle Charging Station. [Final Year Project] (Submitted)

Deep Kumar A/L Pravin Kumar, Deep Kumar (2009) Study on Side Wind Effects on Aircraft Aerodynamics Characteristics. [Final Year Project] (Unpublished)

Dhinakaran Govindasamy, Dhinakaran Govindasamy (2010) Cfd Of Double-Wedge Spiked Intake Of The Supersonic Jet Engine. [Final Year Project] (Unpublished)

Dhuban, Salem Omar Abdullah (2015) Effect of Fiber Orientation and Ply-Stacking Sequence on Buckling Behaviour of Basalt/Epoxy and Basalt-Carbon/Epoxy Composite Laminates. [Final Year Project] (Unpublished)

Dila Sekarini Binti Md Desa, Dila Sekarini (2010) The Study of Intumescent Fire Retardant Coating by Adding Silica Sand as Filler. [Final Year Project] (Unpublished)

Dius, Weltson (2015) Experimental Evaluations of a Novel Invented Wind Turbine for Solar Chimney Power Plant. [Final Year Project] (Unpublished)

Drieberg, Micheal (2010) Channel Assignment Strategies for Throughput Enhancement in High Density Wireless Local Area Networks. [Final Year Project] (Unpublished)

Dzulkifli, Muhammad Nazri (2008) AERODYNAMIC CHANGES WHEN TWO VEHICLES ARE IN PROXIMITY TO EACH OTHER. [Final Year Project] (Unpublished)

E

EL ADAWY, MOHAMMED ABD EL MOTLEB KOTB (2019) CHARACTERIZATION OF FLOW STRUCTURES IN THE CYLINDER OF A GDI ENGINE USING STEREOSCOPIC-TIME RESOLVED PIV AND POD. PhD. thesis, Universiti Teknologi PETRONAS.

EMALISA BINTI KAMSANI, EMALISA (2012) DEVELOPMENT OF AN AUTOMATED FLOW RATE ESTIMATION METHOD. [Final Year Project] (Unpublished)

EMAMIAN, SEYED SATTAR (2018) SURFACE ENHANCEMENT AND TOOL LIFE INVESTIGATIONS OF FRICTION STIR WELDING TOOL. PhD. thesis, Universiti Teknologi PETRONAS.

Edwin Cheng Eu , Winn (2009) Study & Analysis on Regenerative Suspension as part of Hybrid Vehicle System. [Final Year Project] (Unpublished)

Ee, TeikMun (2008) Pilot Study on Laminated Tooling with Implementation of Conformal Channel. [Final Year Project] (Unpublished)

EhsanulHaqGlani, Syed (2013) DESIGN AND FABRICATION OF WIND POWER EXPERIMENT LAB KIT. [Final Year Project] (Unpublished)

Eisa Musa, Ahmed Yosreldin (2016) AEROSTAT EFFECT ON UAV STABILITY. [Final Year Project] (Submitted)

Elavarasu, Vinoshan (2021) Effect Of Tungsten Carbide Tool On The Mechanical Properties Of Friction Stir Lap Welded Aluminium And Stainless Steel Alloy. [Final Year Project] (Submitted)

Elfaki, Mohamed Abdelgadir Mohamed Ahmed (2014) Fire Safety Modeling Of Offshore Petroleum Facilities Platform. [Final Year Project] (Unpublished)

Elias, Noor Fadhilah (2014) Influence of Mengkuang Fiber Orientation on the Strength of Its Composite. [Final Year Project] (Unpublished)

Eliz Ibrahim Mohamed, Mohamed Mamdouh Abou ELIZ IBRAHIM MOHAMED (2023) Experimental Assessment Of A Solar Still Integrated With Thermal Energy Storage And Compound Parabolic Concentrator. Masters thesis, Universiti Teknologi PETRONAS.

Elliza, Amir Zhafri (2011) Computer Aided Design of FPSO Vessel for Deepwater Operations. [Final Year Project] (Unpublished)

Elsaied Mohamed, Waiel Kamal (2009) Performance Optimization of Gas Turbine Engine by Direct-Contact-Air-Washer. Masters thesis, Universiti Teknologi PETRONAS.

Emier Helmee Md Dewa, Emier Helmee (2008) Redesign and Fabrication of a Mechanical Seal for Pumps. [Final Year Project] (Unpublished)

Engelbert, Christine (2011) Study on Heat Treatment Effect on Corrosion of API 5L X52 steel in C02 Environment. [Final Year Project] (Unpublished)

Eva Sarah Bt Zakaria, Eva Sarah (2010) Combustion of Diesel and Syngas Mixtures in a 2-Stroke Diesel Engine. [Final Year Project] (Unpublished)

F

FARHOOD, NASEER HAMED (2019) EXPERIMENTAL AND FINITE ELEMENT ANALYSIS OF IMPACT DAMAGE RESISTANCE ON TYPE IV CARBON-BASALT/EPOXY HYBRID COMPOSITE PRESSURE VESSELS. PhD. thesis, Universiti Teknologi PETRONAS.

FAROOQ, I AZAM (2019) ANALYSIS OF SIXBAR LINKAGE APPLICATION TO GLOBE VALVE. Masters thesis, Universiti Teknologi PETRONAS.

FATAH, MARTIN CHOIRUL (2013) MECHANISTIC AND KINETIC STUDIES OF MICROBIOLOGICALLY INFLUENCED CORROSION(MIC) IN THE PRESENCE OF DOMINANT SULPHATE REDUCING BACTERIA (SRB) METABOLIC SPECIES. PhD. thesis, Universiti Teknologi PETRONAS.

FENTAYE, AMARE DESALEGN (2019) GAS TURBINE CONDITION MONITORING AND MAINTENANCE THROUGH AN INTEGRATED INTELLIGENT GAS-PATH DIAGNOSTICS. PhD. thesis, Universiti Teknologi PETRONAS.

FERN FERN, RACHAEL TAN (2015) Rag Layer Formation and Stability of Crude Oil Emulsion Under Different Imposed Mechanical Energy and Temperatures. [Final Year Project] (Unpublished)

FIRAS BASIM, ISMAIL ALNAIMI (2010) DESIGN AND IMPLEMENTATION OF INTELLIGENT MONITORING SYSTEMS FOR THERMAL POWER PLANT BOILER TRIPS. PhD. thesis, UNIVERSITI TEKNOLOGI PETRONAS.

FUA-NIZAN, ROSDAYANTI (2020) THE STUDY OF CUSTOM-FITTED FEMORAL COMPONENT KNEE IMPLANT FOR HIGH FLEXION. Masters thesis, Universiti Teknologi PETRONAS.

FUDZIN, AHMAD FAUZI (2017) TECHNO-ECONOMICS REPLACEMENT MODEL OF PAINTING ROBOTS IN AUTOMOTIVE MANUFACTURING PLANT. Masters thesis, Universiti Teknologi PETRONAS.

Faezah Binti Mohd Nor, Faezah (2010) A Study of The Effect of Weathering on The Expansion of Intumescent Fire Retardant Coating. [Final Year Project] (Unpublished)

Fahmi bin Ali, Fahmi (2008) Design and Analysis of Suspension System for a Formula SAE Race Car. Other thesis, Universiti Teknologi Petronas.

Faimaize Bin Ibrahim, Faimaize (2012) Effect of Drag Reducing Agent (DRA) In the Injection Well. [Final Year Project] (Unpublished)

Faizul Azizi b. Ahmad Nordin, Faizul Azizi (2010) Effect of welding tool geometry on microstructure and hardness in Friction Stir Welded Plates. [Final Year Project] (Unpublished)

Fakurruddin, Fauzan Bin (2009) DESIGN OF PROPULSION SYSTEM FOR UNDERWATER REMOTELY OPERATED VEHICLE (ROV). [Final Year Project] (Unpublished)

Farah Liyana Binti Ab. Ghani, Farah Liyana (2010) Uniformity of Plating Thickness of IC Packages at Various Locations on its Lead Frame. [Final Year Project] (Unpublished)

Farhanah Binti Ismail, Farhanah (2010) Reliability Modelling of a Diesel Engine System Using Fault Tree Analysis Approach. [Final Year Project] (Unpublished)

Farid Fawzy Fathy Taha Ellakany, Farid Fawzy (2011) Preliminary Drying of Oil Palm Fronds Using Concentrated Solar Thermal Power. [Final Year Project] (Unpublished)

Faris, Muhamad Arif (2016) CREEP ASSESSMENT OF REFORMER TUBE BY ULTRASONIC ATTENUATION AND MICROSTRUCTURE ANALYSIS. [Final Year Project]

Fariza Fansara Binti Fauzi, Fariza Fansara (2012) Study on Thermal Performance Assessment of Solar Hot Water Systems (SHWS) in Malaysia. [Final Year Project] (Unpublished)

Farooq, Muhammed Umer (2014) A Novel Automated Model Generation Algorithm for High Level Fault Modeling of Analog Circuits. Masters thesis, Universiti Teknologi PETRONAS.

Fatah, Martin  Choirul (2013) Mechanistic and kinetics Studies of Microbiologically Influenced Corrosion (MIC) in the Presence of dominant Sulphate Reducing bacteria (SRB) Metabolic Species. Doctoral thesis, Universiti Teknologi PETRONAS.

Fauthan, Aziah Auluwon (2014) The Effect of Post Weld Heat Treatment (PWHT) Temperature on 316L Stainless Steel with Gas Metal Arc Welding (GMAW)/ Metal Inert Gas (MIG). [Final Year Project] (Unpublished)

Fauzi, Mohamad Azrin (2015) Study of the Cutter Design of PDC Drill Bits on Effect of Back Rake Angle and Size of the Cutter on Wear Rate. [Final Year Project] (Unpublished)

Fazmi Yuhanis bt Awang, Fazmi Yuhanis (2010) Comparative Analysis of Machinability of Grey Cast Iron between Conventional and Non-conventional Machining. [Final Year Project] (Unpublished)

Fifizy Hafiz Safidil, Fifizy Hafiz (2010) Design Of A Crushing Mechanism For A Biomass Briquetting Machine. [Final Year Project] (Unpublished)

Fikri Bin Muhamad Ismail, Fikri (2010) Computer Simulation of Hollow Buckling Cylinder Tubing by Finite Element Analysis. [Final Year Project] (Unpublished)

Fung, Chun Ting (2005) Systematic design of simply structures compensator / by Fung Chun Ting, TJ 223 .P55 C559 2005. [Final Year Project]

G

GEBREMARIAM, MEBRAHITOM ASMELASH (2013) THE EFFECTS OF SILICA SAND (Si02) AND ZIRCONIA (Zr02) ON THE MECHANICAL AND THERMAL PROPERTIES OF THE PRESSURELESS SINTERED Al203-Si02-Zr02 COMPOSITE. PhD. thesis, Universiti Teknologi PETRONAS.

GEBREMEDHEN, HAILU SHIMELS (2018) ENHANCING COMPUTATIONAL EFFICIENCY OF STRESS CONSTRAINED TOPOLOGY OPTIMIZATION. PhD. thesis, Universiti Teknologi PETRONAS.

GERARD , SUE WEI PING (2015) Monotonic Burst Pressure of Non-Metallic Filament Wound Composite Pipe. [Final Year Project] (Unpublished)

GHANI, FATIN SYAMIMI (2017) THE EFFECT OF CUTTING SPEED AND FEED RATE ON THE DRILLED HOLES QUALITY OF TITANIUM ALLOYS, TI-6AL-4V. [Final Year Project]

GILANI, SYED EHSAN-UL-HAQ (2016) HEAT TRANSFER ENHANCEMENT OF A FREE CONVECTIVE SOLAR AIR HEATER USING CONICAL PIN TURBULATORS. Masters thesis, Universiti Teknologi PETRONAS.

GOVINDERJIT SINGH, GOVINDERJIT SINGH (2012) Study of Friction Welding on Conventionel Lathes Machine. [Final Year Project] (Unpublished)

GURCHRAN SINGH, HARVIN KAUR (2014) CAVENSIDH BANANA PEELAS A DRAG REDUCTION AGENT. Masters thesis, Universiti Teknologi PETRONAS.

Ganesan, Kogulan (2021) The Effects of Metal Organic Framework (MOF) On Thermal Performance of Intumescent Fire-Retardant Coating. [Final Year Project] (Submitted)

George, Jeffy Cherian (2022) Study of mechanical and thermal properties of MXene - PVDF hybrid composite film for automotive industry. [Final Year Project] (Submitted)

Ghanizadeh, Amir Hossein (2009) Analysis of Gas Turbine Blade Cooling System. [Final Year Project] (Unpublished)

Ghazali, Ahmad Farhan Izzuddin (2021) Evaluation of Cathodic Protection Potential Criteria for Stainless Steel and Carbon Steel Couple in Seawater Environment. [Final Year Project] (Submitted)

Ghazali, Ahmad Farhan Izzuddin (2021) Evaluation of Cathodic Protection Potential Criteria for Stainless Steel and Carbon Steel Couple in Seawater Environment. [Final Year Project] (Submitted)

Ghazali, Nur Ajwa (2021) Study of Preferential Weld Corrosion in Carbon Dioxide Environment with Flowing Conditions. [Final Year Project] (Submitted)

Gobalu, G.Kabhilan (2020) Molybdenum Disulphide/Cellulose Acetate Nanofiber Composite on Screen Printed Electrodes for Determining Cardiac Disease by Electrochemical Impedance Spectroscopy. [Final Year Project] (Submitted)

Goo Jia Jun, Goo Jia Jun (2012) Characterization of Swirling Fluidized Bed. [Final Year Project] (Unpublished)

Guangul, Fiseha Mekonnen (2014) Gasification of Oil Palm Fronds with Preheat Inlet Air. Doctoral thesis, Universiti Teknologi PETRONAS.

Gui, Carina Gui Su Ping (2010) Burst Test Simulation of Corroded Pipelines. [Final Year Project] (Unpublished)

Gunawan, Nugroho (2010) Classes and Properties of Exact Solutions to the ThreeDimensional Incompressible Navier-Stokes Equations. PhD. thesis, Universiti Teknologi PETRONAS.

Gunnasegaran, Paarthiban (2011) Loss Circulation Material in Drilling Fluid. [Final Year Project] (Unpublished)

Gunnasegaran, Paarthiban (2011) Loss Circulation Material in Drilling Fluid. [Final Year Project] (Unpublished)

H

HAFIZ!, MOHD NORSHAHRUL (2011) DESIGN OF HEAT EXCHANGER FOR THE GAS TURBINE AIR INLET COOLING. [Final Year Project] (Unpublished)

HAGOS, FTWI YOHANESS (2013) COMBUSTION, PERFORMANCE, AND EMISSIONS CHARACTERISTICS OF SYNGASES IN A DIRECT-INJECTION SPARK-IGNITION ENGINE. PhD. thesis, Universiti Teknologi PETRONAS.

HAIRUDIN, WAN MASRURAH (2017) THERMOMECHANICAL MODELING OF TURNING PROCESS USING AN ARBITRARY LAGRANGIANEULERIAN (ALE) METHOD. Masters thesis, Universiti Teknologi PETRONAS.

HAIRUMAN, INTAN FARIZA (2011) PUBLIC OCR SIGN AGE RECOGNITION WITH SKEW & SLANT CORRECTION FOR VISUALLY IMP AIRED PEOPLE. [Final Year Project] (Unpublished)

HALLIYEV, SERDAR (2008) RELATIVE PERMEABILITY HYSTERESIS. [Final Year Project] (Unpublished)

HAMDI AL-HAKEEM, SINAN SALMAN (2021) EXPERIMENTAL INVESTIGATION ON NATURAL POLYMER GRAFTED SINGLE AND HYBRID NANOPARTICLES BASED NANOFLUIDS FOR ENHANCED OIL RECOVERY. Doctoral thesis, UNSPECIFIED.

HAMIZOL, MUHAMMAD SYAHMI (2015) DISSERTATION TITLE: EXTRACTION OF CONTINUOUS CELLULOSE FIBER FROM MENGKUANG LEAVES: THE INFLUENCE OF EXTRACTION PROCESS PARAMETERS. Masters thesis, Universiti Teknologi PETRONAS.

HAMIZOL, MUHAMMAD SYAHMI (2011) STUDY OF BONDING STRENGTH OF INORGANIC FILLERS BASED INTUMESCENT COATING. [Final Year Project] (Unpublished)

HAMZA, JASEER ERADEN (2020) VALUATION AND OPTIMIZATION OF CONICAL AXIAL CONCURRENT HYDROCYCLONE SEPARATOR FOR DEOILING APPLICATIONS. PhD. thesis, Universiti Teknologi PETRONAS.

HAMZAH, MOHAMAD NASHRIQ (2021) CHARACTERIZATION OF AA6061/ GRAPHITE COMPOSITES FOR ENHANCED MECHANICAL PROPERTIES USING MULTI-PASS FRICTION STIR PROCESSING. [Final Year Project] (Submitted)

HARBHAJAN SINGH, ALWINJEET SINGH (2021) ANALYZE THE ACCURACY AND PRECISION OF SLIP-ON SPROCKETS. [Final Year Project] (Submitted)

HARBINDER SINGH, ANILDAV SINGH (2012) DEVELOPMENT AND TESTING OF INTUMESCENT FIRE RETARDANT COATING ON VARIOUS STRUCTURAL GEOMETRIES. [Final Year Project] (Unpublished)

HARBINDER SINGH, ANILDAV SINGH (2012) DEVELOPMENT AND TESTING OF INTUMESCENT FIRE RETARDANT COATING ON VARIOUS STRUCTURAL GEOMETRIES. [Final Year Project] (Unpublished)

HARIS, FARHANA (2018) STUDY ON THE INTERFACE REACTION LAYER OF DIFFUSION BONDED SIALON AND DUPLEX STAINLESS STEEL. Masters thesis, Universiti Teknologi PETRONAS.

HARIS, MUHAMMAD (2020) STUDY ON CALCINATION OF HALLOYSITE NANOTUBE (HNT)TO ENHANCE EFFICIENCY OF 2-MERCAPTOBENZOXAZOLE (MBO) LOADED CALCINED HNT EPOXY AS A SMART ANTICORROSIVE COATING FOR CARBON STEEL. Masters thesis, Universiti Teknologi PETRONAS.

HARON, MOHAMMAD FARHAN (2011) ENGINE SELECTION AND DESIGN OF POWERTRAIN FOR SIMPLE VEHICLE FOR OPTIMUM FUEL CONSUMPTION. [Final Year Project] (Unpublished)

HARROUN, MHADI ABAKER ISMAEL (2019) INVESTIGATION ON THE DISPERSED PHASE, DROPLET MICROEXPLOSION AND SPRAY CHARACTERISTICS OF WATER-IN-DIESEL EMULSIONS. PhD. thesis, Universiti Teknologi PETRONAS.

HARUN, MUHAMMAD ERMAN (2017) INFLUENCE OF NITRIDING PROCESS VARIABLES ON THE TENSILE STRENGTH OF AUSTENITIC STAINLESS STEEL 316L. [Final Year Project]

HASAN AZHARI, MUHAMMAD (2013) DYNAMICS OF MAGNETICALLY SUPPORTED RIGID ROTOR IN AUXILIARY BEARING. [Final Year Project] (Unpublished)

HASHMI, MUHAMMAD BAQIR (2020) Transient Modeling and Simulation of Variable Geometry Industrial Gas Turbines. Masters thesis, Universiti Teknologi PETRONAS.

HASNAIN, SYED ALI (2014) NUMERIAL INVESTIGATION ON THE EFFECT OF DOWN STAND STRUCTURE ON SMOKE CONTAMINATION IN ATRIUM UPPER BALCONIES. Masters thesis, Universiti Teknologi PETRONAS.

HASSAN, SALAH ELDIN MOHAMMED ELFAKKI (2018) Development, Performance and Emission Assessment of a Single-cylinder Air-cooled Gasoline Crank-Rocker Engine. PhD. thesis, Universiti Teknologi PETRONAS.

HASSAN, SUHANA (2010) STRESS ANALYSIS ON SIALON/AISI 430 FERRITIC STAINLESS STEEL JOINT. Masters thesis, Universiti Teknologi PETRONAS.

HE , DONGHAI (2020) HYDRODYNAMIC STUDY OF HEAVE COMPENSATED LANDING SYSTEM. Masters thesis, Universiti Teknologi PETRONAS.

HELMY, MOHAMED MAHMOUD ASHRAF (2013) PARAMETRIC SENSITIVITY ANALYSIS FOR THE PERFORMANCE OF STEAM JET EJECTOR. [Final Year Project] (Unpublished)

HEMCHI, THA WEESAK (2008) Thermal Stress and Thermal Expansion in a brake drum of heavy commercial truck. [Final Year Project] (Unpublished)

HILMI, MOHD AFIFIE (2011) ALLOWABLE CORRODED PIPE PRESSURE ESTIMATION DUE TO INTERNAL PRESSURE AND LONGITUDINAL COMPRESSIVE STRESS. [Final Year Project] (Unpublished)

HJ YUSOF, ROSLI (2014) EXPERIMENTAL INVESTIGATION OF VIBRATION CHARACTERISTICS FOR VAPOR CAVITATION EROSION IN PLAIN JOURNAL BEARING. Masters thesis, Universiti Teknologi PETRONAS.

HOCK KING, PAUL TING (2022) The Criticality of Warming up and Idling of Vehicle in Relation to Environment. [Final Year Project] (Submitted)

HOR, WEI VERN (2011) FUNCTIONALIZATION AND CHARACTERIZATION OF MULTI-WALLED CARBON NANOTUBES/POLYPROPYLENE NANOCOMPOSITE. [Final Year Project] (Unpublished)

HOW, KEK JIA (2015) Axial Vibration Analysis on Drillstring. [Final Year Project] (Unpublished)

HUAT, TAN CHEE (2015) Fluid-Structure Interaction of Multiphase Flow within a Pipe Bend. [Final Year Project] (Unpublished)

HUSIRAN, MOHD FAISAL (2004) Simulation Of The Internal Flow Characteristic OfDiesel Injector Using CFD Software. [Final Year Project] (Unpublished)

HUSSAIN, HAIZATUL HAFIZAH (2023) FLOW ASSURANCE INVESTIGATION OF NITROGEN GAS INTRUSION ON THE WAXY CRUDE OIL PIPELINE RESTART. Doctoral thesis, Universiti Teknologi PETRONAS.

HUSSAIN, NAJAF (2017) Analysis of Low-Stiffness-Resilient-Shaft (LSRS) for Semi-Active-Title of thesis Steering (SAS) System. Masters thesis, Universiti Teknologi PETRONAS.

HUSSAIN SADIG, HUSSAIN SADIG (2014) PERFORMANCE AND EMISSIONS OF A MICRO-GAS TURBINE FUELED WITH PRODUCER GAS IN A DUAL FUEL MODE. PhD. thesis, Universiti Teknologi PETRONAS.

HUSSAIN SHAH, SYED ZULFIQAR (2021) CHARACTERIZATION AND DAMAGE MODELLING OF RESIN INFUSED THERMOPLASTIC 3D FIBRE REINFORCED COMPOSITE. Doctoral thesis, UNSPECIFIED.

HUSSEIN, ALAA RAAD (2020) FORMULATION OF RESPONSIVE SIC COMPOSITE BASED SELECTIVE ELECTROMAGNETIC PROPAGATION FOR GHZ APPLICATION. PhD. thesis, Universiti Teknologi PETRONAS.

HUSSEIN, OMAR ASSI (2021) EXPERIMENTAL AND NUMERICAL INVESTIGATION OF HYBRID NANOFLUID WITH CORROBORATIVE CHARACTERISTICS FOR SOLAR COLLECTOR APPLICATIONS. PhD. thesis, Universiti Teknologi PETRONAS.

Hadhri, Hazwan Haziq (2022) Effects Of Amplitudes of External Excitation On Overall Vibration Response of a Piping System. [Final Year Project] (Submitted)

Hafifi bin Mohd Yusop, Hafifi (2008) Modeling and Analysis of Disc Brake Performance. [Final Year Project] (Unpublished)

Hagos, Ftwi Yohaness (2014) Combustion, Performance and Emissions Characteristics of Imitated Syngases in a Direct-Injection Spark-Ignition Engine. Doctoral thesis, Universiti Teknologi PETRONAS.

Hairani Sudin, Hairani (2010) Study Into The Effect Of Crude Palm Oil (CPO) As A Cutting Fluid On Surface Finish During Milling. [Final Year Project] (Unpublished)

Haji Hamzah, Muhamad Syamim (2016) Study of Crude Palm Oil Diesel Blend Emission on Diesel Engine. [Final Year Project] (Submitted)

Haji Karim, Muhammad Fadhil (2011) Study on Characteristics of Syngas Derived From Various Biomasses. [Final Year Project] (Unpublished)

Haji Mohamed Zabidi, Norazreen (2011) Modelling of Polymer Melt During Injection Moulding: Influence of Injection Pressure. [Final Year Project] (Unpublished)

Haji Rosihan, Siti Salmiah (2016) Corrosion Study on X65 Steel with Wax Deposition under Thermal Effect. [Final Year Project] (Submitted)

Halim, Nor Haziyah (2012) STUDY THE EFFECTS OF SINTERING ATMOSPHERE ON CORROSION BEHAVIOR OF POWDER INJECTION MOLDING 316L STAINLESS STEEL. [Final Year Project] (Unpublished)

Halimatulssaadiah binti Wan Jusoh, Halimatulssaadiah (2009) Preliminary Study on the Electromechanical Characterization of Commercial Lead Zirconate Titanate Piezoelectric Ceramic Materials for Flying Micro Robot Actuators. [Final Year Project] (Unpublished)

Hamada, Dah (2016) Drive system design for personal electric vehicle (PEV). [Final Year Project] (Submitted)

Hamat, Mohd Eazaq Farommi (2008) Evaporative Cooler As an Air Inlet Treatment Of Gas Turbine. [Final Year Project] (Unpublished)

Hamdan, Muhammad Fadhli (2022) Studying the Effect of Natural Convection Heat Flow in Compound Parabolic Concentrators (CPC). [Final Year Project] (Submitted)

Hamdan, Khaled (2009) Study on the Essential Variable ofWelding Procedure Specification (WPS) of Fillet Weld. [Final Year Project] (Unpublished)

Hamizol, Muhammad Syahmi (2016) Extraction for Continuos Cellulose Fiber from Mengkuang Leaves: The Influence of Extraction Process Paremeters. Masters thesis, Universiti Teknologi PETRONAS.

Hamssin, Mohamad Fadzley (2013) ANALYSIS OF PINCH AND APPROACH POINT OF HEAT RECOVERY STEAM GENERATOR (HRSG) OF COGENERATION PLANT. [Final Year Project] (Unpublished)

Hamza, Jaseer (2020) Valuation And Optimization Of Conical Axial Concurrent Hydrocyclone Separator For Deoiling Applications. Doctoral thesis, Universiti Teknologi PETRONAS.

Hanaei, Hengameh (2017) Efficiency Enhancement of Silica Solar Cell Using Carbon Nanotubes for Antireflection Self Cleaning Purposes. Doctoral thesis, Universiti Teknologi PETRONAS.

Hanafi, Hairul Azman (2014) SMART SPRINKLER: VARIABLE WATER FLOW USING NOZZLE SIZE CONTROL TO IMPROVE UNIFORMITY. [Final Year Project] (Unpublished)

Hanipah, Mohd Razali (2008) Combustion process in a Two-Stroke, H2-DI Linear Generator Free-Piston Engine during starting. Masters thesis, Universiti Teknologi Petronas.

Haravinthan Arumugam, Haravinthan (2010) Titanium Dioxide-Aluminium High Temperature Thermite Reaction. [Final Year Project] (Unpublished)

Harip, Nur Zaiha Liyana (2021) Azobenzene Derivatives as Corrosion Inhibitors for Carbon Steel Corrosion in Carbon Dioxide (CO2) Saturated Sodium Chloride (NaCl). [Final Year Project] (Submitted)

Haris, Farhana (2013) Comparative Study on the Mechanical and Physical Properties of Un-nitriding and Nitriding of 430 Ferritic Stainless Steel. [Final Year Project] (Unpublished)

Haris, Sakinah (2012) Characterization of Precipitates in Steam Methane Reformer Tubes. [Final Year Project] (Unpublished)

Haris, farhana (2013) Comparative Study on the Mechanical and Physical Properties of Un-nitriding and Nitriding of 430 Ferritic Stainless Steel. [Final Year Project] (Unpublished)

Haron, Hasrizal (2016) Integrated Matrix of 5S and Autonomous Maintenance for the Processing Industry. [Final Year Project] (Submitted)

Haron, Mohamed Haziq (2014) Experimental Investigation of In-situ Oxidation of Soot. [Final Year Project] (Unpublished)

Haron, Mohd Amin (2012) MODAL ANALYSIS OF A TENNIS RACQUET. [Final Year Project] (Unpublished)

Harun, Firdaus (2008) Fitness-for-Service Assessment for Pressurized Components with Geometric Distortion. [Final Year Project] (Unpublished)

Harun, Habibah (2011) Defect Study ofPCBA at Manufacturing Company. [Final Year Project] (Unpublished)

Hasamuddin, Salman (2011) MAINTAINABILITY ANALYSIS OF A BATTERY FOR A PERSONAL TRANSPORTER. [Final Year Project] (Unpublished)

Hasan, Mohamad Zamri (2011) RELIABILITY ASSESSMENT OF A MULTI-STATE SYSTEM USING DISCRETE TIME MARKOV CHAIN. [Final Year Project] (Unpublished)

Hasan, Muhammad Nur Helmi (2015) CFD Simulation of the Aerodynamic Drag of Personal Electric Vehicles (PEV). [Final Year Project] (Unpublished)

Hasbollah, Yasmin Alia (2015) Heat Transfer Performance of a Rotating Phase Change Material (PCM) based Thermal Energy Storage (TES). [Final Year Project] (Unpublished)

Hasbullah Halmi, Muhamad Syamim (2014) Comparative Study of Several Statistical Models in Monitoring the Piping Condition in Petroleum Process. [Final Year Project] (Unpublished)

Hashim, Mohammad Hafiz (2010) Stress Intensity Factor for a Crack in a Strip. [Final Year Project] (Unpublished)

Hashim, Mohd Hafizuddin (2011) FINITE ELEMENT SIMULATION OF RESIDUAL STRESSES IN DIFFERENT COLD-EXPANDED PLATE TIDCKNESS. [Final Year Project] (Unpublished)

Hashim, Mohd Zulkarnain (2012) DEVELOPMENT OF FAULT TREE ANALYSIS FOR COOLING WATER SYSTEM USING SPREADSHEET. [Final Year Project] (Unpublished)

Hashim, Muhammad Khairuddin (2011) Simplified Creep Assessment of Catalyst Tube. [Final Year Project] (Unpublished)

Hasliza bt Omar, Hasliza (2010) A Study on Highway Guardrail Design Improvement. [Final Year Project] (Unpublished)

Hasnain, Syed Ali (2015) Numerical Investigation on the Effect of Down Stand Structure on Smoke Contamination in Atrium Upper Balconies. Masters thesis, Universiti Teknologi PETRONAS.

Hasni, Hadri (2015) Estimating Pump Reliability using Recurrent Data Analysis for Failure Modes. [Final Year Project] (Unpublished)

Hasran bin Che Ismail, Hasran (2010) Stability Analysis of Micro Unmanned Aerial Vehicle during Vertical Take-Off and Landing. [Final Year Project] (Unpublished)

Hassan, Abdullah Fahmi (2016) Evaluation of Hydrogen Embrittlement on Pipeline Steel Due to Cathodic Protection Overpotential. [Final Year Project] (Submitted)

Hassan, Ahmad Hadi Bin (2009) Study on the Air Conditioning Cooling Load and Operational Practices within Glazed Buildings in Universiti Teknologi PETRONAS. [Final Year Project] (Unpublished)

Hassan, Cik Suhana (2008) Stress Analysis of Steam-Methane Reformer Tube. [Final Year Project] (Unpublished)

Hassan, Muhamad Shukri (2020) Integration of RAM Model and DES Method in Assessing Plant Utilization. [Final Year Project] (Submitted)

Hassan, Muhammad Aqib (2021) Improvement in oxidation resistance and electrical properties of SOFCs interconnect via annealing of spinel layer. Masters thesis, Universiti Teknologi Petronas.

Hassan, Muhammad Haziq Hassani (2020) Modelling and Motion Analysis of a Cylindrical Steel-Rod under Very Close Distance between Electromagnets with Alternating Polarities. [Final Year Project] (Submitted)

Hassan, Muhammad Syahiran (2021) Assessment of Straight and Bend Aluminium Alloy 6061 Pipelines Operating Under High Pressure and Temperature Condition Up to 24 Hours by Using Finite Element Analysis. [Final Year Project] (Submitted)

Hassan, Najibah (2013) Thermal Analysis of Carbon Fiber Composite Structure by Finite Element Analysis. [Final Year Project] (Unpublished)

Hassan, Raja Shahzad (2008) Injection Parameters Effect on the Perfom1ance of Compressed Natural Gas Direct Injection (CNG-DI) Engine under Lean Stratified Conditions. Masters thesis, UNIVERSITI TEKNOLOGI PETRONAS.

Hassan Jamil, Roshida (2008) Design ofExperiment on Ultra Violet Curing Die Attach Filmby Using Taguchi Method to Optimize Quality. [Final Year Project] (Unpublished)

Hata Suhaimi, Nurafiqah (2013) S-Cane Pack. [Final Year Project] (Unpublished)

Haur, Lim Chun (2016) Study on the Effect of Ultrasonic Wave Amplitude on Deemulsification of Crude Oil to enhance Production Process. [Final Year Project] (Submitted)

Hazarudin, Nurul ‘Awatif Hanani (2020) Effects of Liquid-Gas Fraction on Vibrational Behaviour of Piping System. [Final Year Project] (Submitted)

Hazri, Muhammad Harris Izuan (2022) An investigation on thermal performance of bio-based filler. [Final Year Project] (Submitted)

Helder Sitoi, Helder (2011) SOLAR POWERED ADSORPTION COOLING SYSTEM USING ACTIVATED MEDIA FOR EQUATORIAL HUMID CLIMATE. [Final Year Project] (Unpublished)

Hendry Hadi bin Hassan, Hendry Hadi (2009) Design and Analysis of an Application of Geo-Exchange Cooling System in Malaysia. [Final Year Project] (Unpublished)

Hendry Hadi bin Hassan, Hendry Hadi (2009) Design and Analysis of an Application of Geo-Exchange Cooling System in Malaysia. [Final Year Project] (Unpublished)

Heng, Yit Man (2015) Experimental Investigation of Roof Top Solar Chimney for Natural Ventilation. [Final Year Project] (Unpublished)

Hian, Kueh Seow (2016) Airflow study of a Split-Type outdoor unit subjected to near wall effect using Computational Fluid Dynamics (CFD)simulation. [Final Year Project] (Submitted)

Hidayah Binti Awalludin, Hidayah (2009) Preliminary Study of Nitration of PETRONAS Calcined Cokes For Water Dispersible Solid Fuel. [Final Year Project] (Unpublished)

Hidayat bin Hamdani, Hidayat (2009) Effect of Electrical Parameters toward Structure and Properties of Anodized Layer in Anodized Aluminum Plates. [Final Year Project] (Unpublished)

Hii, Jun Yew (2008) Polymer-Clay Microcrystalline Composites:Identification of Unique Mechanical Properties. [Final Year Project] (Unpublished)

Hj Osman, Zaino! Rashid (2009) Design and Development of In-motion Tyre Inflator. [Final Year Project] (Unpublished)

Hj Sulaiman, Syahril Izwan (2004) Design and fabrication of a Wing for a Remote-Controlled Electric Powered Airborne Imagery Platform. [Final Year Project] (Unpublished)

Ho , Sir Wee Lee (2008) Study on Corrosion Inhibitor Availability. [Final Year Project] (Unpublished)

Hoe, Wong Leh (2014) Probabilistic Heat Transfer in Variably Random Oil Shale Kerogen Deposit. [Final Year Project] (Unpublished)

Hong, Ho Yik (2016) Burst Strength Analysis of Composite Pressure Vessel using Finite Element Method. [Final Year Project] (Submitted)

Houng Nai Hui, Nai Hui (2010) Development Of Walking Gaits For Quadruped Robot (4-Legged Robot). [Final Year Project] (Unpublished)

Hsien Yoong, John Voon (2016) Effect of the Length of a Torpedo Anchor on Its Vertical Holding Capacity. [Final Year Project] (Submitted)

Huat, Beh Yong (2016) Measurement of Water in Oil Pipelines using Capacitance Method. [Final Year Project] (Submitted)

Huei, Dee Boon (2008) Design and Fabrication of a Lab Scale Thermal Energy Storage in Ice. [Final Year Project] (Unpublished)

Huei Ming, Low (2013) Numerical Simulation of Two-phase Separation in T-junction. [Final Year Project] (Unpublished)

Hui Cin, Chong (2017) Additive Manufacturing for Structures Generated by Topology Optimization. [Final Year Project]

Hung, Tham Wai (2015) Effect of Limestone Catalyst on Production of Synthesis Gas in a Downdraft Co-Gasification of Coconut Frond and Wood Chips. [Final Year Project] (Unpublished)

Huong, Tang Mei (2015) CFD Simulation of Various Types of Solid Particles in Oil Pipe Flow to Evaluate the Pressure Losses. [Final Year Project] (Unpublished)

Husni, Muhammad Umar Rijaluddeen (2011) Development Length for Non-Newtonian Laminar Flow in Circular Pipe. [Final Year Project] (Unpublished)

Hussain, Haizatul Hafizah (2011) Design and Analysis of Flywheel Energy Storage System's Structure. [Final Year Project] (Unpublished)

Hussein, Mohd Al Nazirul Mubin (2016) Electromagnetic Driven Wiper: Conceptual Study and Analysis. [Final Year Project] (Submitted)

Hussein Shah, Mohamad Izzudin (2016) Study of Micro-Explosion Phenomena of Various Water-in-Biodiesel Emulsion (WiBE) Using Visualization Technique. [Final Year Project] (Submitted)

Hussin, Hilmi (2013) Framework for Reliability, Maintainability and Availability Analysis of Gas Processing System During Operation Phase. Doctoral thesis, Universiti Teknologi PETRONAS.

I

IBRAHIM, MUHAMAD HILMEE (2013) NUMERICAL STUDY OF DIFFERENT ORRIFICES SHAPES EFFECT ON THE HYDRODYNAMICS OF BUBBLING FLUIDIZED BED. Masters thesis, UTP.

IBRAHIM MOHMMED, ABDALELLAH OMER (2016) THE EFFECT OF SLUG TWO-PHASE FLOW ON THE MECHANICAL STRESS BEHAVIOUR OF RIGID PIPELINES. PhD. thesis, Universiti Teknologi PETRONAS.

IDRIS, MOHD HAFIZ HIZAMI (2011) Thermal Shrinkage and Gas Void Formation of Waxy Crude Oil-Gas Voids Study. [Final Year Project] (Unpublished)

IKA FARIKHA SYAZWANI BT ABD RAHMAN, IKA FARIKHA SYAZWANI (2012) DESIGN & FABRICATION OF VERTICAL TURBINE FOR RURAL MICRO HYDROELECTRIC GENERATION. [Final Year Project] (Unpublished)

INAYAT, MUDDASSER (2020) CATALYTIC CO-GASIFICATION OF LIGNOCELLULOSIC BIOMASS IN A DOWNDRAFT GASIFIER USING MINERAL CATALYSTS. PhD. thesis, Universiti Teknologi PETRONAS.

INAYAT, MUDDASSER (2015) PRELIMINARY STUDY OF CO-GASIFICATION OF DIFFERENT LIGNOCELLULOSIC BIOMASS IN BENCH SCALE REACTOR. Masters thesis, Universiti Teknologi PETRONAS.

IRSHAD, KASHIF (2016) EXPERIMENTAL STUDY OF THERMOELECTRIC AIR DUCT AND PHOTOVOLTAIC SYSTEM FOR ENERGY EFFICIENT BUILDING DEVELOPMENT. PhD. thesis, Universiti Teknologi PETRONAS.

ISHAK, MIUHAMMAD HARITH IRFAN (2020) MODAL ANALYSIS OF A STRAIGHT PIPE WITH AND WITHOUT FLUID. [Final Year Project] (Submitted)

ISMAEEL, ALI ABDULWAHAB (2018) DEVELOPMENT AND EVALUATION OF DOUBLE SOLAR COLLECTORS INTEGRATED WITH VORTEX POWER GENERATOR. PhD. thesis, Universiti Teknologi PETRONAS.

ISMAEL HARROUN, MHADI ABAKER (2013) SPRAY CHARACTERISTICS AND SPRAY-WALL IMPINGEMENT OF A DIESEL-CNG DUAL FUEL JET USING THE SCHLIEREN IMAGING TECHNIQUE. Masters thesis, UTP.

ISMAIL, AZMAN (2020) INFLUENCE OF FRICTION STIR WELDING PARAMETERS ON THE MECHANICAL PROPERTIES OF AA6063 PIPE BUTT. PhD. thesis, Universiti Teknologi PETRONAS.

ISMAIL, FAISAL (2013) Comparative Study of the Microstructure, Mechanical and Thermal Properties of Nitrided and Base Ferritic SS439 Stainless Steel Rod. [Final Year Project] (Unpublished)

ISMAIL, MOHAMED HAKAM HUSAIRI (2016) RESIDUAL STRENGTH ANALYSIS OF CORRODED PIPELINE WITH SINGLE DEFECT SUBJECTED TO INTERNAL PRESSURE AND LONGITUDINAL COMPRESSIVE STRESS. [Final Year Project] (Submitted)

IYENAGBE, UGHEOKE BENJAMIN (2013) PRODUCTION AND CHARACTERIZATION OF SILICA REFRACTORY FROM RICE HUSK. PhD. thesis, Universiti Teknologi PETRONAS.

Ibrahim, Azman (2014) Assessment of Coating Performance for Underground Pipeline. [Final Year Project] (Unpublished)

Ibrahim, Maziah (2016) A Study Of Shock Absorption Performance Of Tapioca Starch As Cushioning Material For Packaging. [Final Year Project] (Submitted)

Ibrahim, Mohd Madzhir (2011) Dynamic Characteristics of a Hybrid Composite Drive Shaft for Automotive Application. [Final Year Project] (Unpublished)

Ibrahim, Muhamad Farhan (2016) Failure Analysis of Hacksaw Blade. [Final Year Project]

Ibrahim, Muhammad Syaril Azril (2013) Identification and Characterization of Corrosion Scale of Cooler Heat Exchanger. [Final Year Project] (Unpublished)

Ibrahim Mohmmed, Abdalellah Omer (2016) Effect of Slug Two-phase Flow on Fatigue of Pipe Material. Doctoral thesis, Universiti Teknologi PETRONAS.

Idris, Ali Abidin (2015) Pipeline Thermal Insulation for Malaysia’s Deepwater. [Final Year Project] (Unpublished)

Idris, Mohamad Anwar (2015) CONCEPTUAL AND PRELIMINARY DESIGN OF UNMANNED GROUND VEHICLE IN MONITORING OIL AND GAS PLANT. [Final Year Project] (Unpublished)

Idris, Muhammad Khairi (2016) Effect of Sensor-Actuator Non-collocation to Dynamic Response of Flywheel Energy Storage System Supported by Active Magnetic Bearing. [Final Year Project] (Submitted)

Iha @ Ajen, Aileen Julie (2022) Investigation on Fluid Structure Interaction of Composite Piping Conveying Fluid. [Final Year Project] (Submitted)

Ihsan Mohd Zain, Ihsan (2008) Fabrication of a Small Scale Model of Chancellor Award Trophy using CAD/CAM and CNC Milling Machine. Other thesis, Universiti Teknologi Petronas.

Ilias, Ummu Hani (2012) Effect of Different Welding Tool Pin Shapes on Friction Stir Welding Plates Microstructure. [Final Year Project] (Unpublished)

Imam Maarof, Jumaatul Saadiah (2005) The Effect of Surfactant in Lubrication/ by Jumaatul Saadiah Bt Imam Maarof, TJ 1075 .J91 2005. [Final Year Project]

Inayat, Muddasser (2020) Catalytic Co-Gasification of Lignocellulosic Biomass in a Downdraft Gasifier using Mineral Catalysis. Doctoral thesis, Universiti Teknologi PETRONAS.

Irfan, NoorFurqan (2012) Bending Stress Analysis for Spur Gear (2D Analysis). [Final Year Project] (Unpublished)

Irwan Syah Bin Mohd Yasin, Irwan Syah (2008) Design and Fabrication of Hybrid Solar-Biomass System for Crops Drying. [Final Year Project] (Unpublished)

Iryman Fikry bin Salleh, Iryman Fikry (2009) Study on Stress Concentration Factor (SCF) in a Tubular Gap K-Joint Subjected To Axial Loading. [Final Year Project] (Unpublished)

Isa, Ainirullah (2009) EFFECTS OF AERODYNAMIC CHANGES FOR A CAR CAUSED 3BY ANOTHER IN ITS PROXIMITY: NUMERICAL STUDY. [Final Year Project] (Unpublished)

Ishak, Ariff Rahman (2015) A Study of Hybrid Solar Air Conditioning. [Final Year Project] (Unpublished)

Ishak, Mohamad Adib (2011) Design and Implementation of Control System for Fuel Feeding. [Final Year Project] (Unpublished)

Ishak, Muhamad (2011) The Effects of Friction Stir Welding (FSW) of Polypropylene (PP) on Tensile Strength. [Final Year Project] (Unpublished)

Ismail, Azman (2020) Influence of Friction Stir Welding Parameters on the Mechanical Properties of AA6063 Pipe Butt Joints. Doctoral thesis, Universiti Teknologi PETRONAS.

Ismail, Izat Emir (2013) Mechanical Properties of Drilling Defect Induced Glass Fiber Epoxy Composites Developed By Resin Infusion Technique. [Final Year Project] (Unpublished)

Ismail, Maizura (2005) Optimization of pid cController for invertes pendulum system using fuzzy logic controller / by Maizura binti Ismail, TJ 223 .P55 M217 2005. [Final Year Project]

Ismail, Mohammad Afiq Syazwan (2011) Friction Stir Welding of High Density Polyethylene. [Final Year Project] (Unpublished)

Ismail, Mohd Fareid Fareez (2016) Study of Automatic Balancing for Flywheel-based Kinetic Energy Recovery System (KERS). [Final Year Project]

Ismail, Muhammad Hafiz (2014) Evaluation of Effect Of Operating Temperature To Corrosion under Insulation (CUI). [Final Year Project] (Unpublished)

Ismail, Nur Aliana (2015) Experimental Study on Electrical Power Generation from 1 kW Engine Using Simulated Biogas Fuel. [Final Year Project] (Unpublished)

Ismail, Siti Syahirah (2016) Investigation of Performance On Low and High Temperature Nitrided 316L Austenitic Stainless Steel On Impact Test and Scratch Test. [Final Year Project] (Submitted)

Ismail, Syahmi (2020) Finite Element Analysis (FEA) on Friction Stir Welding of Aluminium Alloy, AA5083 Using Coupled Eulerian-Lagrangian Model with Time-Scaling. [Final Year Project] (Submitted)

Ismail , Mohd Fadhlan (2008) Stress Concentration Factors at Two Radial Adjacent Nozzle-Header Connections of a Cylindrical Pressure Vessel. [Final Year Project] (Unpublished)

Ismail Bin Ismayatim, Ismail (2009) Finite Element Analysis of Corroded Pipelines. [Final Year Project] (Unpublished)

Ismaon, Marliana (2004) Modeling of Assembly Line of FinderUnit for Camera. [Final Year Project] (Unpublished)

Iylia Elena binti Abdul Jamil, Iylia Elena (2010) Modelling of Pseudo Hydrostatic Force in Two – Phase Flow with Different Layers. [Final Year Project] (Unpublished)

Izhar Adli Bin Mohd Arif, Izhar Adli Bin Mohd Arif (2009) Study On Piping Stresses At Gas District Cooling (GDC) Universiti Teknologi Petronas (UTP) Plant. [Final Year Project] (Unpublished)

J

JAGINDAR SINGH, TESHVINDER KAUR MANN (2017) COMPARATIVE STUDIES OF ROOT CAUSE ANALYSIS (RCA) TECHNIQUES IN RCA SOFTWARE IN OIL AND GAS INDUSTRY. [Final Year Project]

JAJULI, MUHAMMAD SYAHMI (2017) PHYSICAL AND CORROSION ANALYSIS OF DISSIMILAR METAL WELD OF CARBON STEEL AND AUSTENITIC CARBON STEEL IN MULTIPASS WELD DEPOSIT. [Final Year Project] (Submitted)

JAMAL, IZZAT AMIR ZAFRI (2016) PERFORMANCE OF FREE-PISTON LINEAR GENERATOR BY USING COMPRESSED AIR. [Final Year Project] (Submitted)

JAMALUDDIN, FATIN NABILA (2016) CORRELATION ANALYSIS BETWEEN CHILLED WATER AND ELECTRICAL POWER DEMAND BASED ON GAS DISTRICT COOLING PLANT OPERATIONS. [Final Year Project] (Submitted)

JAMALUDIN, AMIRUL ALIFF (2023) THE SYNERGY APPROACH OF TAGUCHI METHOD AND RSM ON NUMERICAL ANALYSIS OF PDC CUTTER DESIGN OPTIMIZATION. Doctoral thesis, Universiti Teknologi PETRONAS.

JARED SAMUEL S/O THANGGARAJ, JARED SAMUEL (2012) DESIGN OF CENTRAL SOLAR TOWER RECEIVER. [Final Year Project] (Unpublished)

JASMAINE MARSELLA BINTI AKBARJASMAINE MARSELLA BINTI AKBAR, JASMAINE (2011) EFFECTS OF DRILLING PARAMETERS ON HOLE INTEGRITY WHEN DRILLING HYBRID FIBER COMPOSITE HALF CYLINDERS. [Final Year Project] (Unpublished)

JAYA RAMAN, THINESHRAAJ (2016) Study of Preferential Weld Corrosion in X52 Mild Steel with the Presence of Acetic Acid. [Final Year Project] (Submitted)

JAYAID, MUHAMMAD YASAR (2016) EFFECT OF WING FORM AND WATER CURRENT ON THE DYNAMICS OF AN UNDERWATER GLIDER. PhD. thesis, Universiti Teknologi PETRONAS.

JA’AFAR, NUR SYAHIRAH (2020) ANALYSIS OF WATER-COOLED ELECTRIC CHILLER AT DISTRICT COOLING PLANT. [Final Year Project] (Submitted)

JEMAAT, MUHAMAD RIDZUAN (2011) A COMPARATIVE STUDY BETWEEN TWO RESIN INFUSION STRATEGIES IN THE MANUFACTURING OF POLYMER COMPOSITE WIND TURBINE BLADE VIA RESIN INFUSION PROCESS. [Final Year Project] (Unpublished)

JESSAM, RAED ABBAS (2018) EXPERIMENTAL AND NUMERICAL INVESTIGATIONS ON THE PERFORMANCE OF S-SHAPED DIFFUSERS USING ENERGY PROMOTERS. PhD. thesis, Universiti Teknologi PETRONAS.

JIN, JIANG PHUAH (2012) Fractional Flow Analysis for Chemical Flooding in Enhanced Oil Recovery. [Final Year Project] (Unpublished)

JOHAN, AHMAD SY AMIL (2011) Mechanical Properties of Polypropylene/Polycarbonate Blends. [Final Year Project] (Unpublished)

JOHAN, AHMAD SYAMIL (2011) Mechanical Properties of Polypropylene/Polycarbonate Blends. [Final Year Project] (Unpublished)

JOHAR, AIMI NURLIYANA (2011) STUDY ON TENSILE AND FLEXURAL PROPERTIES OF RECYCLED HIGH DENSITY POLYETHELENE/SAWDUST COMPOSITES. [Final Year Project] (Unpublished)

Jaafar, Nur Nabila Najad (2020) Effect of Hybrid Composition and Volume Fraction on Microstructure and Microhardness of 7075 Aluminum Alloy via Friction Stir Processing. [Final Year Project] (Submitted)

Jaalam, Nadiya (2005) Solar cooling system of a car / By Nadiya Binti Jaalam, TJ 810 .N136 2005. [Final Year Project]

Jahir, Mohd Rozairie (2013) Conceptual Design Support Tool for Subsea Equipment. [Final Year Project] (Unpublished)

Jaini, Azmeer Zainurin (2016) Evaluation of “Rust Converter Paint” Mechanism Under Simulated Field Condition. [Final Year Project] (Submitted)

Jalaluddin, Muhamad Imran (2014) CFD Simulation Of 3-D Flow Field Over Clean And Loaded Wing. [Final Year Project] (Unpublished)

Jalilluddin, Amir Fahmi (2013) Development of Fatigue Reliability Model Using Spreadsheet (Steel Structures). [Final Year Project] (Unpublished)

Jamalluddin, Fazli (2014) Hot Corrosion Behaviour of Thermal Spray Coating. [Final Year Project] (Unpublished)

Jamaluddin, Nurul Firdaus (2005) Optimization of PID controller for inverted pendulum system using genetic algorithm / by Nurul Firdaus Binti Jamaluddin, TJ 223 .P55 N974 2005. [Final Year Project]

Jamaludin, Ahmad Ariff (2011) A Study of Energy Recovery Potential from Poultry Industry Waste Sludge. [Final Year Project] (Unpublished)

Jamaludin, Hazirah (2015) Experimental Study on the Influence of Water-in-Diesel Emulsion (WiDE) Characterization on Microexplosion Occurrence. [Final Year Project] (Unpublished)

Jamaludin, Nur Syahadah (2008) Fabrication of Pinion Gear for Power Window of a Car through Powder Metallurgy Technique. [Final Year Project] (Unpublished)

Jamaludin Alias, Nur 'Atikah (2011) Failure Analysis on Heat Exchanger Tube Bundle Leakage. [Final Year Project] (Unpublished)

Jamil, Muhammad Akmal (2016) Study on the Effect of Syngas Fuel Temperature to the Performance of a Small-Scale Electrical Power Generator. [Final Year Project] (Submitted)

Jamil, Nurliana (2005) Modeling and control of a heat exchanger /by Nurliana Binti Jamil, TJ 263 .N974 2005. [Final Year Project]

Javaid, Muhammad Yasir (2016) Effect of Tappered and Rectangular Wing Forms on The Dynamic of an Underwater Glider. Doctoral thesis, Universiti Teknologi PETRONAS.

Javier Teo Han Seong, Javier (2011) Dynamic Analysis of Suspension Bridge. [Final Year Project] (Unpublished)

Jayakumar, Khuganeswaran (2016) Investigation of Organic Rankine Cycle Using Different Working Fluids for Conversion of Low Grade Heat Sources. [Final Year Project] (Submitted)

Jebar, Mohd. Nazri (2011) Design and Fabrication of the Body for Fuel Saving Prototype Car Which Caters For Aerodynamics Purposes. [Final Year Project] (Unpublished)

Jeyaseelan, Deertanan (2021) Preliminary Study on the Synthesis of Silica Dioxide Using CoconutFibre Ash(CFA). [Final Year Project] (Submitted)

Jian, Chou Zhi (2014) Prototype Manufacturability of PDC Drill Bit Body using Sacrificial Patterns with Wax Materials and using 3D Printing Technology. [Final Year Project] (Unpublished)

Jie, Yu Jun (2017) Systematic Procedure of Acid Leaching for Removal of Impurities from Used Abrasive Blasting Media for Powder Metallurgy Application. [Final Year Project]

Jin Ming, Goh (2011) Experimental Investigation of Savonius Wind Rotors in Open and Bounded Flows. [Final Year Project] (Unpublished)

Jinal Ahbidin, Muhammad Firdaus (2016) A STUDY ON THE MECHANICAL EFFECTS OF GAS NITRIDING ON ALUMINIUM ALLOY 6061 FOR THE USE IN MOBILE PHONE CASING. [Final Year Project] (Submitted)

Joel Yeo Eng Hsien, Joel Yeo (2012) Estimation of Tire Cornering Stiffness Using Static Method. [Final Year Project] (Unpublished)

Johani, Syakir Saniy (2011) Design of a High Temperature Steam Generator System using Solar Energy for a Biomass Torrefaction Reactor. [Final Year Project] (Unpublished)

Johar, Mohd Izham (2004) Manufacturing of Composite External Body for Hybrid Electric Vehicle. [Final Year Project] (Unpublished)

Johari, Muhammad Ismeth Amir (2015) The Microstructure, physical and mechanical properties of silicon carbide for high temperature wear application: An Experimental Observation. [Final Year Project] (Unpublished)

John, Marco Jones (2014) Study of Ground Exchange Air Conditioning (GEAC) System Design for A Small House. [Final Year Project] (Unpublished)

Jothiahnantham, Dnesh (2022) Effect Of Hybridization Of Natural And Synthetic Fibers On Tensile Properties Of Composites: A Numerical Study. [Final Year Project] (Submitted)

Jumaah, Sundus Sameer (2017) Experimental and Numerical Parametric Investigation for Performance Enhancement of Solar Chimney Power Plant. Doctoral thesis, Universiti Teknologi PETRONAS.

Jumali, Siti Nur Izzaidah (2016) Reliability, Availability and Maintainability (RAM) Analysis for Offshore High Pressure Compressor. [Final Year Project] (Submitted)

Jun Li, Khor (2013) Residence Time Distribution and Hydrodynamics Studies of a Swirling Fluidized Bed. [Final Year Project] (Unpublished)

Jun Yen, Thomas Chin (2015) Design a Solar Hybrid Air Conditioning Compressor System. [Final Year Project] (Unpublished)

Junaidy, Idlan Akmal (2022) Study of Twisted MXENE/PVDF Nanofiber Yarn. [Final Year Project] (Submitted)

Juni Elyna Jubely, Juni Elyna (2010) Management, Selection, and Installation of engine, powertrain and accessories for The Shell Eco - Marathon 2010 - 1. [Final Year Project] (Unpublished)

K

K.V., SREEJAYA (2013) PARAMETRIC STUDY OF ROOF TOP SOLAR CHIMNEY. PhD. thesis, Universiti Teknologi PETRONAS.

KABIR, A K M SAROWER (2021) INTUMESCENT COATING INFLUENCE ON DRILLED HOLE INTEGRITY OF GLASS-CARBON HYBRID EPOXY COMPOSITE. Masters thesis, Universiti Teknologi PETRONAS.

KAKA, SHUAIB (2018) FUZZY LOGIC-BASED QUANTITATIVE RISK ASSESSMENT MODEL FOR HEALTH SAFETY AND ENVIRONMENT IN OIL AND GAS INDUSTRY. Masters thesis, Universiti Teknologi PETRONAS.

KAKOOEI, SAEID (2013) DESIGN AND f-ABRIC AT! ON OF A SURFACE pH SENSOR FOR A REALTIME CORROSION MONITORING. PhD. thesis, UTP.

KAMARUDIN, NAQIB HAKIM (2013) DEVELOPMENT OF FRAMEWORK USING GROUP TECHNOLOGY APPROACH IN ESTIMATING FABRICATION TIME OF SUBSEA MANIFOLD. [Final Year Project] (Unpublished)

KAMARUZAMAN, NURUL AFIQAH (2017) SIMULATION OF ADSORPTION COOLING SYSTEM DRIVEN BY WASTE HEAT FROM ENGINE. [Final Year Project]

KAMILIN, MUHAMAD HAFIZ (2017) CHARACTERIZATION OF SURFACE CRACK ON STAINLESS STEEL PLATE BY LIQUID PENETRANT TEST AND PHASED ARRAY ULTRASONIC TEST (PAUT). [Final Year Project]

KAMSUL, MOHD SYAHMIE (2011) SMALL ENGINE PERFORMANCE OPTIMIZATION FOR POWER AND FUEL CONSUMPTION IMPROVEMENT OF A SIMPLE VEHICLE. [Final Year Project] (Unpublished)

KAR FYE, CHAN (2012) A STUDY ON AN EVAPORATOR-CONDENSER COMBINATION FOR HUMIDITY CONTROL IN AN AIR-CONDITIONING SYSTEM. Masters thesis, Universiti Teknologi Petronas.

KAR KIN, LOOI (2017) CHARGING PERFORMANCE EVALUATION OF STRATIFIED THERMAL ENERGY STORAGE (TES) BY USING HALF CYCLE FIGURE OF MERIT (1/2 FOM). [Final Year Project] (Submitted)

KEAN, KHOO BOO (2010) MATHEMATICAL MODELING AND CONTROL SIMULATION FOR PETROLEUM PROCESS. Masters thesis, Universiti Teknologi PETRONAS.

KEAT, BEH HARK (2013) THE DESIGN OF STRUCTURE FOR LIFTING HEAVY LOAD. [Final Year Project] (Unpublished)

KEONG, WOO TZE (2016) DEVELOPMENT AND ANALYSIS OF HIGH SPEED DRILLING INDUCED DELAMINATION IN GLASS FIBER REINFORCED POLYMER. PhD. thesis, Universiti Teknologi PETRONAS.

KHAIRULANNUAR, IZZUDIN (2013) ELECTROCHEMICAL NOISE TECHNIQUE IN MONITORING C02 CORROSION IN HIGH PRESSURE AND HIGH TEMPERATURE ENVIRONMENT. Masters thesis, UTP.

KHALILI, AMIRUL AMIN (2022) EVALUATION OF CHEMICAL VAPOUR DEPOSITION COATED FRICTION STIR WELDING TOOL PERFORMANCE IN DUPLEX STAINLESS STEEL WELDING. Masters thesis, UNSPECIFIED.

KHAN, JAVED AKBAR (2013) FILL REMOVAL FROM HORIZONTAL WELLBORE USING FOAM IN COILED TUBING. Masters thesis, UTP.

KHAN, JAVED AKBAR (2018) EXPERIMENTAL AND MATHEMATICAL INVESTIGATION ON THE SEPARATION PREDICTION OF OIL/WATER EMULSIONS FLOODED WITH ALKALI-SURFACTANT-POLYMER. PhD. thesis, Universiti Teknologi PETRONAS.

KHAN, MUHAMMAD HAMMAD (2015) REVISITING FANGER'S THERMAL COMFORT MODEL USING MEAN BLOOD PRESSURE AS A BIO-MARKER: AN EXPERIMENTAL INVESTIGATION. Masters thesis, Universiti Teknologi PETRONAS.

KHAN, MUHAMMAD MOHSIN (2016) DEVELOPMENT OF A FUZZY LOGIC BASED MODEL FOR CORROSION UNDER INSULATION IN PIPING SYSTEMS. Masters thesis, Universiti Teknologi PETRONAS.

KHAN, SAJJAD RAZA (2019) EXPERIMENTAL EVALUATION OF FATIGUE AND DYNAMIC TENSILE PROPERTIES OF REFILL FRICTION STIR SPOT WELD. PhD. thesis, Universiti Teknologi PETRONAS.

KHAW , YAO SHUN (2015) Ultrasonic wave application to crude oil de-emulsification process. [Final Year Project] (Unpublished)

KHLIEF, AYAD KADHIM (2019) MATHEMATICAL MODELING AND EXPERIMENTAL EVALUATION OF AN EVACUATED TUBE RECEIVER AND PVT USING HELIOSTAT CONCENTRATORS. PhD. thesis, Universiti Teknologi PETRONAS.

KHOO, BOO KEAN (2015) EXPERIMENTAL AND NUMERICAL SIMULATION STUDY OF INDUCTOR FAULT BY INVESTIGATING WINDING CONTOUR. PhD. thesis, Universiti Teknologi PETRONAS.

KHOO, SZE WEI (2017) DEVELOPMENT OF A FATIGUE DAMAGE MONITORING SYSTEM USING DIGITAL IMAGE CORRELATION. PhD. thesis, Universiti Teknologi PETRONAS.

KHOR, YIN YIN (2019) NUMERICAL STUDY ON THE GEOMETRY OPTIMISATION OF HYDROCYCLONES FOR DOWNHOLE OIL-WATER SEPARATION. PhD. thesis, Universiti Teknologi PETRONAS.

KHYE YEE, YONG (2017) Obstacle Avoidance System in Underwater Glider. [Final Year Project]

KINAN, AZRIE (2017) COMPUTATIONAL FLUID DYNAMICS (CFD) SIMULATION OF SAND DEPOSITION IN PIPELINE. [Final Year Project]

KIONG, CHONG KIAN (2013) ANALYTICAL STUDIES ON VOLUME DETERMINATION OF LEG ULCER USING REVERSE ENGINEERING METHOD. Masters thesis, Universiti Teknologi PETRONAS.

KIONG, CHONG KIAN (2014) VOLUME DETERMINATION OF LEG ULCER USING REVERSE ENGINEERING METHOD. Masters thesis, Universiti Teknologi PETRONAS.

KOH , KELLY (2020) EXPERIMENTAL EVALUATION OF LOW ENERGY BUILDING USING DOUBLE-SKIN GREEN FAÇADE IN TROPICAL CLIMATE. Masters thesis, Universiti Teknologi PETRONAS.

KON KIT LUNG, KON KIT LUNG (2012) MATERIAL FLOW STUDY DTTRING FRICTION STIR WELDING OF DISSIMILAR MATERIAL. [Final Year Project] (Unpublished)

KONDA KUKU, RAMZY ELNEEL (2013) UPDRAFT GASIFICATION OF OIL PALM FRONDS. PhD. thesis, UTP.

KONDA KUKU, RAMZY ELNEEL (2014) EXPERIMENTAL STUDY ON UPDRAFT GASIFICATION OF OIL PALM FRONDS. PhD. thesis, Universiti Teknologi PETRONAS.

KU ARIFFIN, KU MUHAMMAD FAEZ (2018) PERFORMANCE ANALYSIS OF GROOVED HYDRODYNAMIC JOURNAL BEARING WITH TEXTURE AND SLIP SURFACE. Masters thesis, Universiti Teknologi PETRONAS.

KUANG, ZHI WEN (2020) WATER AND GAS ABSORPTION OF POLYTETRAFLUOROETHYLENE AS A PIPELINE. [Final Year Project] (Submitted)

Kah Ling, Isabel Goh (2013) Estimation of Time between Failures and Time to Repairs of a Repairable System Based On Performance Data. [Final Year Project] (Unpublished)

Kalai Chelven, A K Kariigesh (2009) Experimental and Numerical Investigation on 2-D Wing-Gronnd Interference. [Final Year Project] (Unpublished)

Kalai Chelven, A K Kartigesh (2009) ExperimentaLand Numerical Investigation on 2-D Wing-Ground Interference. [Final Year Project] (Unpublished)

Kamalruzzaman, Muhammad Fadhullah (2016) Prevention of Evaporative Water Loss in Water Reservoir Dam. [Final Year Project]

Kamaruddin, Haikal (2020) STUDY OF FRICTION STIR WELDING TOOL’S COATING MATERIAL (TiAlN) FOR TUNGSTEN CARBIDE COBALT. [Final Year Project] (Submitted)

Kamaruddin, Nur Zatil Ilham (2013) Tensile Strength of Woven Kenaf Reinforced High Density Polyethylene (HDPE) Composites. [Final Year Project] (Unpublished)

Kamarudin, Noor Maisarah (2009) Computer-Aided Inspection Approach Using 3D Digitizer. [Final Year Project] (Unpublished)

Kamarudin, Nur Azmel Zaa (2011) Study of Liquid Flow with Air Bubbles in a Pipe. [Final Year Project] (Unpublished)

Kamarul Ariffin B Kasnin, Kamarul Ariffin (2010) Drag Reduction on How to Improve Fuel Consumption of a Vehicle. [Final Year Project] (Unpublished)

Kamarul Bahrin, Muhammad Kamil (2011) Spray Characteristics of Non-Newtonian Fluids. [Final Year Project] (Unpublished)

Kamarul Bahrin B. Mohd Kamil, Kamarul Bahrin (2008) Temperature Distribution on a Car Disc Brake. [Final Year Project] (Unpublished)

Kamarulzaman, Mohd Nizam B. (2009) Failure Analysis of The Copper Tubes for A Water Heater. [Final Year Project] (Unpublished)

Kan Sze Wei, Kan Sze Wei (2012) The Effect of Preferential Weld Corrosion Study in CO2 Capture Plant at PFK. [Final Year Project] (Unpublished)

Kang , Chin Ann (2020) Development of Thermoplastic 3D Woven Composite. [Final Year Project] (Submitted)

Kardan, Ramtin (2016) Combustion Characteristics of a Curved-Cylinder Crank-Rocker Engine. [Final Year Project] (Submitted)

Karthegesu, Shamni (2020) Predicting the Tensile Properties of Recycled Polypropylene (r-PP)/Mengkuang Leaf Fibre (MLF) Composite using Mathematical Modelling. [Final Year Project] (Submitted)

Kashfi, Mohammadmahdi (2017) Influence of micro-size titanium powders on mechanical properties of powder injection molded 316L stainless steel. [Final Year Project] (Submitted)

Kathiravan, Dinish Mutu (2022) Numerical Simulation Of Temperature Distribution During Friction Stir Processing (AA7075). [Final Year Project] (Submitted)

Kee Lian Soon, Kee Lian (2011) Experimental Study of Oil Palm Biomass Waste Mixture for Energy Potential. [Final Year Project] (Unpublished)

Khadijah Hasshim, Khadijah (2009) Simulation of Crosswind Effects on Rail Vehicles. [Final Year Project] (Unpublished)

Khairil Fadzli Bin Abu Bakar, Khairil Fadzli (2010) “A Numerical Investigation Into The Thermal Distribution In A Steam Cracking Furnace” Optimal Chemicals (M) Sdn. Bhd. Case Study. [Final Year Project] (Unpublished)

Khairil Ikhwan Bin Abdul Rahman, Khairil Ikhwan (2012) Development of Diagnostic Program for Gas Compressor using Knowledge Based Management Concept. [Final Year Project] (Unpublished)

Khairil Nizam Bin Mohamad Darus, Khairil Nizam (2010) Palm Waste Briquette & Bio-Briquette As Potential Fuel. [Final Year Project] (Unpublished)

Khairuddin, Muhammad Hariz (2013) Mechanical and Physical Effect of Nitriding AISI 316L Austenitic Stainless Steel at Various High Temperatures and Different Gas Nitriding Methods. [Final Year Project] (Unpublished)

Khairul Anuar, Daniel Affendy Amri (2020) Tensile Properties Prediction of Polypropylene Reinforced Woven Kenaf Composite using Micromechanical Models. [Final Year Project] (Submitted)

Khairul Anuar B Kamarul Baharin, Khairul Anuar (2010) Design And Fabrication Of Biomass Burner For Gas To Gas Heat Exchanger. [Final Year Project] (Unpublished)

Khairul Anwar Bin Hasni, Khairul Anwar (2012) Stress Analysis of Steam-Methane Reformer Tubes. [Final Year Project] (Unpublished)

Khairul Anwar bin Azhari, Khairul Anwar (2010) Design of Food Processing Mechanism for An Automatic Sandwich-Making Vending Machine with Filling Selection. [Final Year Project] (Unpublished)

Khairul Ashraf Bin Minhat, Khairul Ashraf (2012) Effects of Drilling Induced Defects and Mechanical Properties of GFRE Composites. [Final Year Project] (Unpublished)

Khairul Fariz bin Khalil, Khairul Fariz (2009) Application of SIMULINK to Emulate Subsea Production System (SPS) Control Functions. [Final Year Project] (Unpublished)

Khairul Izzat Bin Amriem, Khairul Izzat (2010) Computer Aided Design (CAD) of Tension Leg Platform (TLP) Hull for Deepwater Operation. [Final Year Project] (Unpublished)

Khairul Jafni B Abd Hamid, Khairul Jafni (2010) Development of Alternative Fuel Briquettes from Poultry Processing Waste (Collecting, Storage and Handling). [Final Year Project] (Unpublished)

Khairul Nazmi Bin Ahmad Majdi, Khairul Nazmi (2011) Performance Improvement of Photovoltaic Panels Through Mitigation of Surface Temperature Cooling and Debris Removal. [Final Year Project] (Unpublished)

Khairul Salleh, Nur Sakinah (2014) Study of a low temperature waste heat driven sorption chiller. [Final Year Project] (Unpublished)

Khairulannuar, Redhwan Ariff (2021) Replacement Model for Discrete Manufacturing Facilities Adopting Job Shop Type Production. [Final Year Project] (Submitted)

Khairunnisa Bte Md. Said, Khairunnisa (2010) Study On Solar Organic Rankine Cycle Using Geothermal Energy. [Final Year Project] (Unpublished)

Khalid, Muhamad Fazillah (2016) Iridium Oxide pH Microsensor Based on Stainless Steel Wire for pH Mapping on Metal Surface. [Final Year Project]

Khamis, Kamarul Azrin (2013) Vehicle Scheduling System. [Final Year Project] (Unpublished)

Khamis, Nur Syaheerah (2012) Computer Aided Design of Semi-Submersibles for Deepwater Operations. [Final Year Project] (Unpublished)

Khan, Mohammed Yahaya (2017) Investigation of Water in Bio Diesel Emulsions on the Microexplosion Behaviour and Engine Performance. Doctoral thesis, Universiti Teknologi PETRONAS.

Khan, Muhammad Hammad (2016) Experimental Investigation to Modify the Fanger's Thermal Comfort Model using Blood Pressure as Bio-Maker in the Tropical Climate. Masters thesis, Universiti Teknologi PETRONAS.

Khan, Muhammad Mohsin (2017) Development of a Fuzzy Logic based Prediction Model for Corrosion under Insulation in Carbon Steel Piping Systems. Masters thesis, Universiti Teknologi PETRONAS.

Khan, Muhammad Rehan (2020) Development Of Semi Empirical Sand Fines Erosion Model For Elbows In Liquid-Solid And Slug Flow. Doctoral thesis, Universiti Teknologi PETRONAS.

Khang, Jeff @ Kuek Jun (2020) Knowledge-Based Front-End Engineering Design for Gas-Liquid Separator. Masters thesis, Universiti Teknologi PETRONAS.

Kheng Tat, Beh (2009) Design and Development of Hands-On Learning Kit for Statics. [Final Year Project] (Unpublished)

Khoo, Boo Kean (2016) Numerical Simulation and Experimental Study of Inductor Fault for Different Winding Contours. Doctoral thesis, Universiti Teknologi PETRONAS.

Khoo, Sze Wei (2009) Stress Intensity Factor for a Crack Emanating From a Shaft. [Final Year Project] (Unpublished)

Khor, Yin Yin (2020) Numerical Study on Geometry Optimisation of Hydrocyclones for Downhole Oil-Water Seperation. Doctoral thesis, Universiti Teknologi PETRONAS.

Khor, Yin Yin (2009) Numerical Simulation of Solar-Flue Gas Chimney for Energy Recovery. [Final Year Project] (Unpublished)

Kimin, Mohd Azrul Amin (2008) PRELIMINARY DESIGN OF PALM Oil. FROND GASIFIIm. [Final Year Project] (Unpublished)

Kizilov, Annanur (2009) Feasibility Study of Jatropha Based Mud for High Pressure Low Temperature Wells. [Final Year Project] (Unpublished)

Kok, Chee Kang (2009) Design and Development of Above Knee Prosthetic Knee Joint by Applying Design for Manufacture (DFM) Methodologies. [Final Year Project] (Unpublished)

Komarudin, Aiman Hamzi (2021) Finite Element Analysis of Composite Hybrid Pipes through Ring Tests. [Final Year Project] (Submitted)

Kong, Chai Chen (2008) The Study of Flow Characteristic in the Riser Pipe from the Subsea Wellhead to Kikeh FPSO. [Final Year Project] (Unpublished)

Kong , Chai Chen (2008) The Study of Flow Characteristic in the Riser Pipe from the Subsea Wellhead to Kikeh FPSO. [Final Year Project] (Unpublished)

Kresnajaya , Prasetia Pancakarsa (2009) Design of Contraflow Cleaning PIG for Pipeline Maintenance. Masters thesis, UNIVERSITI TEKNOLOGIPETRONAS.

Krishnamoorthy, Shasidaran (2016) Optimum Welding Parameters for Pipeline Welding Using Artificial Neural Network. [Final Year Project] (Submitted)

Ku Ariffin, Ku Muhammad Faez (2015) Design and Development of Portable Hand-Crank Generator. [Final Year Project] (Unpublished)

Kueh, Shao Chih (2021) Chemically Infused Scale Inhibitor Based Nanoadditives in Porous Proppants for Improved Fracture Conductivity. [Final Year Project] (Submitted)

Kum, Chee Mun (2008) Design of Multi-Cavity Injection Mold for Tensile and Flexural Test Specimens. [Final Year Project] (Unpublished)

Kum , Chee Mun (2008) Design of Multi-Cavity Injection Mold for Tensile and Flexural Test Specimens. [Final Year Project] (Unpublished)

Kum , Chee Yan (2009) CFD Simulation of Two Phase Flow and Hydrate Prediction in a Pipeline. [Final Year Project] (Unpublished)

Kumanan A/L Raman, Kumanan (2010) Manufacturing Systems Design For Mass Production Of Disc Brakes. [Final Year Project] (Unpublished)

Kumar, Arvindren (2014) Vibration Analysis of Vertical Centrifugal Pump. [Final Year Project] (Unpublished)

L

LEE, KUO CHUN (2011) Study on the Effectiveness of Ionic Liquid as Low Dosage Hydrate Inhibitor (LDID) for Flow Assurance in Pipeline. [Final Year Project] (Unpublished)

LEONG, KHAI SIANG (2008) Drilling Fluid Loss Control By Using Oil Palm Fibres. [Final Year Project] (Unpublished)

LIM , SlOW LING (2004) PRODUCTION OF METAL-BASED IMPLANTS FOR CYRO-FACIAL INJURIES (BLUEPRINTS). [Final Year Project] (Unpublished)

LOOI, KAR KIN (2019) PERFORMANCE AND LIFE CYCLE COST ANALYSIS OF A PHOTOVOLTAIC THERMOELECTRIC SYSTEM FOR ROOM COOLING APPLICATION. Masters thesis, Universiti Teknologi PETRONAS.

Lai Kok Soon, Lai Kok Soon (2012) Multiphase Flow in Naturally Fractured Reservoirs: Comparison of Matrix-Fracture Shape Factor and Transfer Function. [Final Year Project] (Unpublished)

Lal, Chandreshah (2020) DETERMINATION OF FRACTURE TOUGHNESS AND STRAIN ENERGY RELEASE RATE FOR BASALT/EPOXY COMPOSITES. [Final Year Project] (Submitted)

Lanai Wan, Alvin (2010) The Effects of Filler Loading on Mechanical Properties of Coir and Bagasse Reinforced Polyethylene Biocomposites. [Final Year Project] (Unpublished)

Lau , Kah Mun (2016) Investigation of Heat Transfer Losses to the Combustion Chamber Wall of a Linear Generator Engine. [Final Year Project] (Submitted)

Law , Tzee Sien (2016) Lean Process Improvement on Local Hospitals. [Final Year Project] (Submitted)

Le , Bang Duc (2008) Designing Omni-Directional Mobile Robot Platform for Research. [Final Year Project] (Unpublished)

Lee, Holinson (2013) EFFECT OF FUNCTIONALIZATION ON THE STRENGTH OF MULTI-WALL CARBON NANOTUBES-POLYPROPYLENE (MWCNTs-PP) COMPOSITE. [Final Year Project] (Unpublished)

Lee, Jin Ming (2010) Three-Dimensional Analysis on Thermal Stresses in A Perforated Disc Brake of Vehicle. [Final Year Project] (Unpublished)

Lee, Keng Huai (2010) Design of Tracking System for Alzheimer Patients. [Final Year Project] (Unpublished)

Lee, Sooyong (2003) Passive Two-Camera System to Generate a Depth Map of a Scene and Depth Estimation using Optical Flow Techniques. [Final Year Project] (Unpublished)

Leong, Song Seng (2008) Customizing Prosthetic Leg Socket by using Rapid Prototype with Reverse Engineering. [Final Year Project] (Unpublished)

Leong , Ian Mun Choong (2010) Design and Fabrication of a Fuel Efficient Simple Vehicle Chassis. [Final Year Project] (Unpublished)

Lias, Mohd Rizal (2017) Development of Bending Fatigue Life Mathematical Model For Spur Gear in Misalignment Conditions. Doctoral thesis, Universiti Teknologi PETRONAS.

Liew, Zhi Bin (2021) Study of Rooftop Hybrid Solar Wind Renewable Energy Applications for East Coast of Peninsular Malaysia. [Final Year Project] (Submitted)

Lim, Chung Hyan (2009) Small Scale Rotational Moulding Machine. [Final Year Project] (Unpublished)

Lim , Kha Loon (2009) Riser Stress Analysis with Finite Element Approach. [Final Year Project] (Unpublished)

Loganathan, Narasimhaa Naidu A/L (2023) Synthesis and Characterization of Laser Scribed Graphene from Oil Palm Lignin for High-Performance Supercapacitors. Masters thesis, Universiti Teknologi PETRONAS.

Loh, Xi Li (2020) Numerical Investigation of Geometrical Tolerance Effect on Torque and Power Output of Slip-On Sprocket. [Final Year Project] (Submitted)

Long Zainudin, Long Zulkamaen (2011) Design of an Optical Box for Laser Doppler Anemometer Measurements. [Final Year Project] (Unpublished)

Longwa Milia, Richard Lado (2008) OPTIMIZATION OF. DRILLING HYDRAULICS IN VERTICAL HOLES. [Final Year Project] (Unpublished)

Loqman, Muhammad Aliff Ashman (2013) Conceptual Design Support Tool For Offshore Platform Jacket Design. [Final Year Project] (Unpublished)

Lubis, Abdul Munir Hidayat Syah (2014) Tribological Study of Jatropha Oil as Boundary Lubricant. Doctoral thesis, Universiti Teknologi PETRONAS.

Luis-Casiano Ndong Mikue, Luis-Casiano Ndong Mikue (2009) Study on Pumping System Design for Water Injection. [Final Year Project] (Unpublished)

Lutfullaev, Jamshid (2015) Preventive Maintenance & Replacement Scheduling Model for Repairable and Maintainable Systems. [Final Year Project] (Unpublished)

ldris, Muhammad Hazri (2011) Stress Analysis of Steam-Methane Reformer Tubes. [Final Year Project] (Unpublished)

llham, Muhammad Afif (2011) Design and Analysis of Run-of-River Water Turbine. [Final Year Project] (Unpublished)

M

M.K. GANESAN, ARUJENDRAN (2011) Design and Development of Body Panel for UTP's Shell Eco-Marathon Vehicle. [Final Year Project] (Unpublished)

MACHMUDAH, AFFIANI (2018) META-HEURISTIC AND GEOMETRICAL BASED MOTION PLANNING OF INDUSTRIAL MANIPULATOR. PhD. thesis, Universiti Teknologi PETRONAS.

MAHAMAT, AL TIDJANI ZAKARIA (2013) SYNTHESIZING ANDEVALUATION OFNEWCOPPER-TUNGSTEN BASED EDM ELECTRODE FOR MACHINING HARDENED MATERIALS. PhD. thesis, Universiti Teknologi PETRONAS.

MAHAMAT, AL TJDJANI ZAKARIA (2012) SYNTHESIZING AND EVALUATION OF NEW EDM ELECTRODE MATERIALS FOR MACHINING HARDENED DIE-STEEL USING TAGUCHI TECHNIQUE. PhD. thesis, Universiti Teknologi PETRONAS.

MAHARUN, MUI’NUDDIN BIN (2009) DESIGN AND ANALYSIS OF A SMALL RACE CAR BODY FRAME. [Final Year Project] (Unpublished)

MAHGOUB, BAHAADDEIN KAMAL MOHAMED (2018) INVESTIGATION OF ZERO CARBON DIOXIDE SYNGAS-BIODIESEL BLENDS FOR DUAL FUELING OPERATION IN A CI ENGINE. PhD. thesis, Universiti Teknologi PETRONAS.

MAHMUD, ABDULLAHI (2021) SYNTHESIS OF POLY (OCTANEDIOL CITRATE) BASED NANO SILICA COMPOSITE FOR BIOMEDICAL APPLICATION. PhD. thesis, Universiti Teknologi PETRONAS.

MAHMUD, MUHAMMAD NABIL AHNAF (2021) COATING PERFORMANCE UNDER EXCESSIVE CATHODIC POLARIZATION. [Final Year Project] (Submitted)

MAILABARI, RAPHAEL JOSHUA (2019) SYNTHESIS AND CHARACTERIZATION OF HYBRID NANO-FILLER REINFORCED EPOXY NANOCOMPOSITE FOR STRUCTURAL HEALTH MONITORING OF PETROLEUM PIPELINE. PhD. thesis, Universiti Teknologi PETRONAS.

MARTANG, MOHD NUR IZZWAN (2020) COMBUSTION ANALYSIS OF WATER-IN-BIODIESEL EMULSIFIED FUELS. [Final Year Project] (Submitted)

MASA ALOGO BINDANG, Manuel (2008) Investigation of the Environmental Effect on Adhesive Bonds. [Final Year Project] (Unpublished)

MAT SHAYUTI, MUHAMMAD SHAFIQ (2021) MECHANISM OF CRUDE OIL REMOVAL FROM SAND USING ULTRASONIC ENERGY. Doctoral thesis, UNSPECIFIED.

MAT SHAYUTI, MUHAMMAD SHAFIQ (2012) THERMAL, WATER ABSORPTION, AND MECHANICAL PROPERTIES OF POLYPROPYLENE – GRAFT – MALEIC ANHYDRIDE COMPATIBILIZED POLYPROPYLENE / POLYCARBONATE BLENDS. Masters thesis, Universiti Teknologi PETRONAS.

MAT YAAKOB, SARINI (2021) PERFORMANCE EVALUATIONS OF GLASS FIBER REINFORCED GEOPOLYMER COMPOSITES AS COATING FOR CARBON STEEL PROTECTION FROM CORROSION. Doctoral thesis, UNSPECIFIED.

MAZLAN, NISHA FAIRUZ (2021) THE INFLUENCE OF PROCESSING PARAMETERS ON THE FORMATION OF SILICON DIOXIDE FROM RICE HUSK. [Final Year Project] (Submitted)

MAZLI, AIMADUDDIN (2004) [DESIGN AND FABRICARION OF SMALL WIND TUNNEL FOR FLOW VISUALIZATION]. [Final Year Project] (Unpublished)

MD RAZIB, NUR SYAFIQAH (2011) STUDY OF WEATHER RESISTANCE OF INORGANIC FILLERS BASED INTUMESCENT COATING. [Final Year Project] (Unpublished)

MD SALLEH, SHAHRUL NIZAM (2017) TENSILE, PHYSICAL AND CHEMICAL CHARACTERIZATION OF PAN FIBRE MODIFIED WITH OLEIC ACID POST SPINNING TREATMENT. Masters thesis, Universiti Teknologi PETRONAS.

MD SHAHID, ABDUL MUHAIMIN (2014) A Study of Semi-Active Steering System Performance On An All-Wheel Drive Flat Chassis Vehicle. [Final Year Project] (Unpublished)

MD SHAHSAZIZAN, IKHWAN (2013) MODELING AND SIMULATION OF A PERPETUAL PIGGING MECHANISM. [Final Year Project] (Unpublished)

MD TUMIRAN, NADIAH (2011) PERFORMANCE STUDY OF 1 BIT STATIC RAM BASED ON PROCESS TECHNOLOGIES. [Final Year Project] (Unpublished)

MD YAZID, MUHAMMAD HAIDAR (2009) A Fundamental Study on Drying Characteristics of Oil-Palm Fronds for Gasification. [Final Year Project] (Unpublished)

MD. IBRAHIM, NOR NURULHUDA (2015) DIFFUSION BONDING AND POST-BOND HEAT TREATMENT OF SIALON TO NITRIDED A lSI 420 STAINLESS STEEL. PhD. thesis, Universiti Teknologi PETRONAS.

MEKBIB ATNAW, SAMSON (2013) GASIFICATION OF OIL PALM FRONDS IN A DOWNDRAFT GASIFIER. PhD. thesis, Universiti Teknologi PETRONAS.

MEKONNEN GUANGUL, FISEHA (2013) ENHANCEMENT OF OIL PALM FRONDS GASIFICATION PROCESS USING PREHEATED INLET AIR. PhD. thesis, Universiti Teknologi PETRONAS.

MENGAL, ALI NAWAZ (2016) FATIGUE LIFE PREDICTION OF BASALT- CARBON HYBRID COMPOSITE FOR WIND TURBINE ROTOR BLADES. PhD. thesis, Universiti Teknologi PETRONAS.

MEYGHANI, BAHMAN (2018) THERMOMECHANICAL ANALYSIS OF FRICTION STIR WELDING (FSW) ON CURVED PLATES BY ADAPTING CALCULATED TEMPERATURE DEPENDENT PROPERTIES. PhD. thesis, Universiti Teknologi PETRONAS.

MOHAMAD AF ANDI, NUR HASYIMAH (2008) STUDY OF ZEOLITE IN MITIGATING FORMATION DAMAGE DUE TO INORGANIC SCALING. [Final Year Project] (Unpublished)

MOHAMAD ALI, MOHAMAD ROZAIDI (2013) ESTABLISHING CORRELATION BETWEEN LEAF SPRING’s SPECIFICATIONS AND CAMBER DROP. [Final Year Project] (Unpublished)

MOHAMAD FAIZAL AZRI BIN AZAHARI, MOHAMAD FAIZAL AZRI (2012) Corrosion Characterization of Salvaged Subsea Pipeline. [Final Year Project] (Unpublished)

MOHAMAD FARID, AIDIL AIZAT (2013) FACTORS AFFECTING PLASTERING EFFECT IN CASING WHILE DRILINNG. [Final Year Project] (Unpublished)

MOHAMAD JAMEL BASHA, MOHD HAFIF BASHA (2021) INVESTIGATION OF DOWNDRAFT CO-GASIFICATION OF PALM KERNEL SHELL AND POLYSTYRENE WITH AIR AS THE GASIFYING AGENT FOR PRODUCTION OF SYNTHESIS GAS. Doctoral thesis, UNSPECIFIED.

MOHAMAD KHAIRI, MUHAMMAD SYAFIQ (2013) COMPARATIVE STUDY ON HONEYCOMB STRUCTURE FOR WEIGHT REDUCTION OF GANGWAY MONORAIL. [Final Year Project] (Unpublished)

MOHAMAD NOOR IMAN, Mohd Nor (2013) A STUDY OF TORQUE VECTORING AND TRACTION CONTROL FOR AN ALL-WHEEL DRIVE ELECTRIC VEHICLE. [Final Year Project] (Unpublished)

MOHAMAD SAYUDI, MOHAMAD NURHALIM (2011) DESIGN OF THE DETACHABLE HUB FOR TURBINE BLADE COOLING SYSTEM. [Final Year Project] (Unpublished)

MOHAMED, MOHAMED OSMAN ABDALLA (2013) ENERGY SAVINGS AND SPEED IMPROVEMENT IN LINEAR POWER HYDRAULIC ACTUATORS USING A SELF-ACTUATED FLOW CONTROL VALVE. PhD. thesis, Universiti Teknologi PETRONAS.

MOHAMED HISHAM, MOHAMED SYAKIR (2016) A STUDY OF PHYSICAL PROPERTIES & SHOCK ABSORPTION ABILITIES OF STARCH POLYMER FOAM AS CUSHIONING MATERIAL FOR PACKAGING. [Final Year Project] (Submitted)

MOHAMED KHAIRI, MOHAMED IKRAM (2020) COMPUTATIONAL FLUID DYNAMIC (CFD) SIMULATION OF SLUG FLOW WITHIN PIPE BEND AND PIPE ELBOW WHICH INDUCE VIBRATION. [Final Year Project] (Submitted)

MOHAMED NYAN, ANAS (2009) THE PERFORMANCE EVALUATION OF FOUR TYPES WATER SOFTENER USED FOR BOILER. [Final Year Project] (Unpublished)

MOHAMED TERMIZI, NOOR ANIZA (2015) THERMOGRAVIMETRIC KINETIC ANALYSIS OF POULTRY PROCESSING DEWATERED SLUDGE FOR THERMOCHEMICAL CONVERSION PROCESS. Masters thesis, Universiti Teknologi PETRONAS.

MOHAMMAD, SANAN T. (2018) EXPERIMENTAL IMPLEMENTATION AND CODE DEVELOPMENT TO EVALUATE A PARABOLIC TROUGH SOLAR THERMAL POWER PLAN. PhD. thesis, Universiti Teknologi PETRONAS.

MOHAMMAD, SYAZWAN FIKRI (2020) THERMAL DEGRADATION BEHAVIOUR OF CARBON FIBRE WASTE AS A FILLER IN POLYMER HYBRID COMPOSITES. [Final Year Project] (Submitted)

MOHAMMAD ALSAAFEEN, MOUAATH (2017) Characterization and Properties Investigation on the Industrial Mold finishing stone. [Final Year Project]

MOHAMMAD PURE, SHAHAB HAMDAVI (2017) ANALYSIS OF HYDRODYNAMIC JOURNAL BEARING WITH AN AXIAL GROOVE. Masters thesis, Universiti Teknologi PETRONAS.

MOHAMMAD RADZI, NURUL HIDAYAH (2009) METAL-TO-METAL SEALING FOR fflGH PRESSURE SUBSEA PRODUCTION SYSTEM (SPS) BOLTED FLANGE CONNECTOR. [Final Year Project] (Unpublished)

MOHAMMAD SAIF, MOHD AFIQ (2015) EVALUATION OF EFFECT OF INSULATION MATERIALS TO CORROSION RATE FOR CORROSION UNDER INSULATION (CUI). [Final Year Project] (Unpublished)

MOHAMMADPOUR, EHSAN (2013) TENSILE BEHAVIOR EVALUATION OF CARBON NANOTUBE/POLYPROPYLENE COMPOSITES USING NONLINEAR FINITE ELEMENT MODELING. PhD. thesis, Universiti Teknologi PETRONAS.

MOHAMMED AL-DHAHEBI, ADEL MOHAMMED (2023) DEVELOPMENT OF ELECTROSPUN MXENE/POLYVINYLIDENE FLUORIDE NANOFIBER COMPOSITES APTASENSOR FOR EFFICIENT DETERMINATION OF OCHRATOXIN A. Doctoral thesis, UNSPECIFIED.

MOHAMMED MUTAFI, MOHAMMED ABDULLAH (2019) NUMERICAL INVESTIGATION ON THE EFFECT OF BALCONY OPEN UPSTAND ON SMOKE CONTAMINATION IN ATRIUM UPPER BALCONIES. Masters thesis, Universiti Teknologi PETRONAS.

MOHAN, GOPI NATH NAMBIAR (2017) INFLUENCE OF DEPOSITION TEMPERATURE ON THE CORROSION RESISTANCE OF ELECTRODEPOSITED ZINC-NICKEL ALLOY COATINGS. [Final Year Project] (Submitted)

MOHD AIZAT BIN ZAINAL, MOHD AIZAT (2012) PERSONAL ELECTRIC VEHICLE PROTOTYPE DEVELOPMENT. [Final Year Project] (Unpublished)

MOHD AZLAN, MOHAMAD NAZRIN SHAH (2018) RESIDUAL STRENGTH ANALYSIS OF SINGLE CIRCUMFERENTIAL CORROSION GROOVE SUBJECTED TO INTERNAL PRESSURE AND LONGITUDINAL COMPRESSIVE STRESS. [Final Year Project] (Submitted)

MOHD HAFIZ HIZAMI BIN IDRIS, MOHD HAFIZ (2011) Thermal Shrinkage and Gas Void Formation of Waxy Crude Oil –Gas Voids Study. [Final Year Project] (Unpublished)

MOHD HALIMI, MUHAMMAD HAZIM (2015) Modeling and Simulation of a Free Floating PIG for Different Inclination Angle using CFD. [Final Year Project] (Unpublished)

MOHD JANI, NORANIZA (2019) THE PERFORMANCE OF BASALT AND PVA FIBRE REINFORCED SELF-COMPACTING CONCRETE SLABS SUBJECTED TO HIGH INTENSITY FIRE. Masters thesis, Universiti Teknologi PETRONAS.

MOHD KHAIRAN, SYAFIQ (2012) A STUDY OF AUTO-REINFORCED MAGNETIC FLYWHEEL'S PERFORMANCE. [Final Year Project] (Unpublished)

MOHD LAZIZ, AFIQ (2021) CFD SIMULATION AND EXPERIMENTAL STUDY ON HYDRODYNAMIC BEHAVIOUR OF TRANSESTERIFICATION REACTION IN MICROCHANNEL REACTOR. PhD. thesis, Universiti Teknologi PETRONAS.

MOHD MOKHTAR, MUNAIBAH (2013) NUMERICAL MODELLING AND SIMULATION OF BONE DRILLING TO MINIMIZE BONE NECROSIS BY CONTROLLING HEAT GENERATIONS. Masters thesis, UTP.

MOHD NASHIR, MOHD RIDHWAN (2012) INSITU PRODUCTION OF NANO METAL MATRIX COMPOSITE (NANO MMC’s) USING FRICTION STIR PROCESSING (FSP). [Final Year Project] (Unpublished)

MOHD NOOR, SITI NURSYUKRINA (2021) EXPERIMENTAL INVESTIGATION ON THE ADSORPTION OF GRAPHENE NANOPLATELETS INTO SANDSTONES USING SODIUM CARBOXYMETHYL CELLULOSE. [Final Year Project] (Submitted)

MOHD NOR, MOHD AZRI (2021) ANALYSIS AND OPTIMIZATION OF HYDROCYCLONE GEOMETRY USING BOX-BEHNKEN AND MULTI-OBJECTIVE OPTIMIZATION ALGORITHM. Doctoral thesis, UNSPECIFIED.

MOHD PAUZI, AIDA KHALEEDA (2016) Rotor Dynamic Analysis of Centrifugal Compressor due to Liquid Carry Over. [Final Year Project] (Submitted)

MOHD RAHIM, MOHD NUZUL SYAZWAN (2012) INVESTIGATION OF PARTICLE MOTION IN A SWIRLING FLUIDIZED BED USING PARTICLE TRACKING VELOCIMETRY. [Final Year Project] (Unpublished)

MOHD RUSLAN, MOHD SYAFIQ (2012) Design Continuous Variable Transmission for Shell Eco Marathon Asia 2012 (SEM2012). [Final Year Project] (Unpublished)

MOHD SAIFUDDIN, MUHAMMAD SYAMIM (2021) Effects of Void Fractions on Vibration Behaviour of Pipe Conveying Fluids. [Final Year Project] (Submitted)

MOHD SALEH, MOHAMMAD IZZAT (2013) GAS TURBINE PERFORMANCE AT VARYING AIR INLET TEMPERATURE. [Final Year Project] (Unpublished)

MOHD SAMSURI, MUHAMAD SHAZARIZUL HAZIQ (2017) CHARACTERIZATION AND PROPERTIES INVESTIGATION OF SINGLE ROW DEEP GROOVE BALL BEARING FAILURE. [Final Year Project] (Unpublished)

MOHD SHAFIQ AHMAD DAHALAN, MOHD SHAFIQ (2008) Extract Motion from Picture Sequence. [Final Year Project] (Unpublished)

MOHD SHAFRI, MOHD IZWAN SHAFIQ (2012) TENSILE AND FLEXURAL PROPERTIES OF COMMINGLED KENAF/PET REINFORCED POLYPROPYLENE HYBRID COMPOSITES. [Final Year Project] (Unpublished)

MOHD SHARFRI, RAIHAN AMALINA (2017) The Development of Synthetic Algorithm of Fluid Flow Through Particle Image Velocimetry (PIV). [Final Year Project]

MOHD YASIN, AMMAR NAZIRUL BIN MOHD YASIN (2021) ADAPTIVE NEURAL-FUZZY INFERENCE SYSTEM (ANFIS) PREDICTION OF CARBON DIOXIDE (CO2) HYDRATE FORMATION KINETICS. [Final Year Project] (Submitted)

MOHD YATIM, MUHAMMAD FARHAN (2020) SOOT REMOVAL SYSTEM USING ELECTROMAGNETIC WAVE HEATING FOR VEHICLE EXHAUST AFTER TREATMENT. [Final Year Project] (Submitted)

MOHD YUNOS, YUSNENTI FAZIRAN (2018) SILICANIZING PROCESS ON MILD STEEL SUBSTRATE USING TRONOH SILICA SAND (SiO2) FINE PARTICLES. PhD. thesis, Universiti Teknologi PETRONAS.

MOHD ZAID, AHMAD AMIR FARHAAN (2017) PRODUCTION OPTIMIZATION OF GRAPHENE OXIDE VIA ELECTROCHEMICAL EXFOLIATION. [Final Year Project]

MOHD ZAMRI, MUHAMMAD ZUL IRFAN (2013) EXPERIMENTAL ANALYSIS OF COMPATIBILITY BETWEEN CORROSION INHIBITOR AND BIOCIDE USING ELECTROCHEMICAL IMPEDANCE SPECTROSCOPY. [Final Year Project] (Unpublished)

MOHD ZUL AKMAL BIN ZAINAL ABIDIN, MOHD ZUL AKMAL (2011) Design of Modular Fixture for CNC Machining Center. [Final Year Project] (Unpublished)

MOHD ZULHELMIE BIN DERAMAN, MOHD ZULHELMIE (2011) AUTOMOTIVE ENGINE HEAT MANAGEMENT SYSTEM SHMS – SMART HEAT ENGINE MANAGEMENT. [Final Year Project] (Unpublished)

MOHD ZULHELMIE BIN DERAMAN, MOHD ZULHELMIE (2011) AUTOMOTIVE ENGINE IIEAT MANAGEMENT SYSTEM SHMS - SMART HEAT ENGINE MANAGEMENT. [Final Year Project] (Unpublished)

MOHD ZULKIFLI, MUHAMAD SYAHMI (2013) EFFECT OF SALINITY OF CONCENTRATION OF POLYMER SOLUTION ON VISCOSITY. [Final Year Project] (Submitted)

MOHD. YUSOFF, AHMAD SYAUFIK (2008) Bio-ethanol Fuel Study on Spray Characterization Using High Speed Digital Camera. [Final Year Project] (Unpublished)

MOHIDEEN BATCHA, MOHO FAIZAL (2015) AERODYNAMICS AND HYDRODYNAMICS OF A SWIRLING FLUIDIZED BED WITH SLOPED DISTRIBUTOR. PhD. thesis, Universiti Teknologi PETRONAS.

MOHMAD @ FIKRI, FAEZ (2016) INVESTIGATION OF TITANIUM ADDITION ON PHYSICAL AND MECHANICAL PROPERTIES OF POWDER INJECTION MOLDED 316L STAINLESS STEEL PARTS. [Final Year Project] (Submitted)

MOKHLIF, NASSIR DHAMIN (2013) MODELLING OF WAX CRYSTALLIZATION IN SOLVENT DEW AXING SCRAPED SURF ACE EXCHANGERS AND CHILLERS. PhD. thesis, UTP.

MOKHLIS, MOHAMAD MOHAIMIN (2014) SIMULATION AND ANALYSIS OF POWER EXTRACTION FROM A CRANK-ROCKER MECHANISM AT THE ROCKER PIVOT USING A CONVERTER MECHANISM. Masters thesis, Universiti Teknologi PETRONAS.

MONARSHAH, MUHAMMAD ALFIAN UMAR (2015) MATERIAL FLOW BEHAVIOUR DURING FRICTION STIR WELDING (FSW) OF NYLON PLATES. [Final Year Project] (Unpublished)

MONI, MOHAMAD NAZMI ZAIDI (2019) DOWNDRAFT CO-GASIFICATION OF OIL PALM BIOMASS FOR PRODUCTION OF SYNTHESIS GAS. PhD. thesis, Universiti Teknologi PETRONAS.

MOSTAFA MOHAMED HEIKAL, RAGHDA MOHAMED (2013) Flow Distribution Inside An Air Conditioning Distributor Using FLUENT Simulation. [Final Year Project] (Unpublished)

MUGILAN A/L MALAI RAJAN, MUGILAN (2012) The effect of hybrid filler loading on mechanical and physical properties of Epoxy Bio-Composite. [Final Year Project] (Unpublished)

MUHAMMAD AQMAL BIN RATASHA, MUHAMMAD AQMAL (2008) Implementation of Risk-Based Inspection on Offshore Facilities. [Final Year Project] (Unpublished)

MUHAMMAD HAZIQ, A.KADIR (2011) CHARACTERISATION OF INTER-LAMINAR SHEAR STRENGTH (ILSS) OF A RESIN INFUSED WIND TURBINE BLADE POLYMER COMPOSITE VIA THE SHORT BEAM SHEAR TEST. [Final Year Project] (Unpublished)

MUHAMMAD KAMAL, MUHAMMAD MARZUKI (2011) Rheological Characterization of Thixotropic Waxy Crude. [Final Year Project] (Unpublished)

MUHAMMAD KHAIRIL ANUAR BIN MOKHTAR, MUHAMMAD KHAIRIL (2008) DESIGN AND DEVELOPMENT OF A SOLAR COOKER. [Final Year Project] (Unpublished)

MUHAMMAD LUQMAN MOHD NASIR, MUHAMMAD LUQMAN (2012) Development of an Effective Drying System to Improve the Fuel Quality of Poultry Waste Material Using FLUENT Simulation. [Final Year Project] (Unpublished)

MUHAMMAD NAZRI BIN DZULKIFLI, MUHAMMAD NAZRI (2008) Aerodynamic changes when two Vehicles are in a Proximity to each other. [Final Year Project] (Unpublished)

MUHAMMAD SOLIHIN BIN MOHAMED AMIR, MUHAMMAD SOLIHIN (2011) MECHANICAL PROPERTIES OF PP/PET (POLYPROPYLENE AND POLY(ETHYLENE TEREPHTHALATE)) MICROFIBRILLAR COMPOSITE WITH AND WITHOUT COUPLING AGENT. [Final Year Project] (Unpublished)

MUHAMMAD SYAHMI HAMIZOL, MUHAMMAD SYAHMI (2011) STUDY OF BONDING STRENGTH OF INORGANIC FILLERS BASED INTUMESCENT COATING. [Final Year Project] (Unpublished)

MUHAMMED JUSOFFE PEREIRA, MUNTAQIM SHAH PEREIRA (2013) SIMULATION OF OIL – WATER INTERACTION AT DOWNHOLE. [Final Year Project] (Unpublished)

MUHIDDIN, MUHAMMAD HAKIM (2015) SIMULATION & VALIDATION OF BODY FRAMING ASSEMBLY LINE USING WITNESS. [Final Year Project] (Unpublished)

MUJAHID, YASIR (2021) EFFECTS OF VACUUM-BAG-ONLY PROCESSING PARAMETERS ON SHAPE CONFORMATION, VOID CONTENT AND MECHANICAL PROPERTIES OF COMPOSITES. Masters thesis, Universiti Teknologi PETRONAS.

MUJTABA, SYED MUHAMMAD (2020) ADAPTIVE THRESHOLD BASED LEAK DETECTION SYSTEM FOR GAS MIXTURE PIPELINES. Masters thesis, Universiti Teknologi PETRONAS.

MUSA, NURUL FERLIENA (2021) RELIABILITY, AVAILABILITY AND MAINTAINABILITY (RAM) ANALYSIS AND THE DEVELOPMENT OF COGENERATION PLANT RELIABILITY BLOCK DIAGRAM (RBD). [Final Year Project] (Submitted)

MUSHTAQ, SHAHRYAR (2018) Design, development and experimental validation of dual output stator-less motor. Masters thesis, Universiti Teknologi PETRONAS.

MUSHTAQ, SHAHRYAR (2016) FEASIBILITY STUDIES OF CONVERTING A MECHANISM INTO A DUALOUTPUT PULSATING STATOR-LESS MOTOR. Masters thesis, Universiti Teknologi PETRONAS.

MUSTAFA, ASRUL (2014) LIGNIN FILLED NATURAL RUBBER LATEX COMPOSITES AND ITS UTILIZATION IN RUBBER PRODUCTS. PhD. thesis, Universiti Teknologi PETRONAS.

MUSTAFA, AYAD TAREQ (2015) INVESTIGATION AND EVALUATION OF DEVELOPED SOLAR VORTEX ENGINE. PhD. thesis, Universiti Teknologi PETRONAS.

MUSTAFA KAMAL, MOHD AIDIL FIRDAUS (2020) STUDY OF STABILITY AND THERMAL CONDUCTIVITY OF MULTIWALL CARBON NANOTUBES AND COPPER OXIDE IN ETHYLENE GLYCOL AT MEDIUM TEMPERATURE. [Final Year Project] (Submitted)

MUSTAFA MUSA, ABDEL HAFIZ (2013) CORROSION INHIBITION OF X52 STEEL IN HIGH PRESSURE CARBON DIOXIDE (C02) ENVIRONMENT. PhD. thesis, Universiti Teknologi PETRONAS.

MUSTAPHA, MAZLI (2010) A Novel Approach to The Fabrication of Aluminium Foam Through Pressure Assisted High-Frequency Induction Heated Sinterin2 Dissolution Process (P ASDP). PhD. thesis, Universiti Teknologi PETRONAS.

Mahadzir, Irwan Haadi (2004) Monitoring Solar Data near Equator. [Final Year Project] (Unpublished)

Mahamad Rezali, Muhamad Izdan Zul Izzi b. (2009) DESIGN HARNESSING HOT SPRING’S ENERGY SYSTEM FOR COCOA BEANS DRYING. [Final Year Project] (Unpublished)

Mahamad Rezali, Muhamzad Izdan Zul Izi (2009) DESIGN HARNESSING HOT SPRINGS ENERGY SYSTEM FOR COCOA BEANS DRYING. [Final Year Project] (Unpublished)

Mahamed Salleh, Afdzal Zullah (2013) Computer Aided Design of a Deepwater Floater. [Final Year Project] (Unpublished)

Maharun, Mui'nuddin (2009) Design and Analysis ofA Small Race Car Body Frame. [Final Year Project] (Unpublished)

Mahayadin, Hazeem (2015) Performance Study of Corrosion Inhibitors for CO2 Corrosion on Pre-Corroded Carbon Steel. [Final Year Project] (Unpublished)

Mahir Elya El feel Agla, Mahir Elya (2008) Improving Hole Cleaning on High Angle Wells. [Final Year Project] (Unpublished)

Mahli, Mohd Hazman (2014) A Comprehensive Study of Convective and Radiation Heat Transfer in the Flat Plate Absorber Region of a Solar Dryer. [Final Year Project] (Unpublished)

Mahmoud, Ali Moghavvemi (2016) Investigation on the Phalange Contact Force for a 2 finger Pulley-Tendon Driven Robotic Hand. [Final Year Project] (Submitted)

Majid, Mohd. Saifullah bin (2009) Design and Analysis of a Double Wishbone Suspension System. [Final Year Project]

Makalo Koos Khojane, Makalo (2009) Simulation of Fluid Flow in a Furnace Top Model of an Ethane Cracker. [Final Year Project] (Unpublished)

Makentheran, Kayilass Hari Nair (2020) DYNAMIC ANALYSIS FOR SELF –LOCKING TRAPEZOIDAL ORIGAMI SHELL STRUCTURE. [Final Year Project] (Submitted)

Manogran, Johan Suppiah (2021) Ultra-Thin Nanocomposite Layers Coated Proppant for improved Compression Strength. [Final Year Project] (Submitted)

Mansor, Amnah Bashirah (2013) Study of Characteristics of Contaminants during Eggs Hatching Using Incubator. [Final Year Project] (Unpublished)

Mansor, Mohd Noor Hazman (2009) Study on C02 Corrosion in Oil Producing Well. [Final Year Project] (Unpublished)

Mansor, Mohd Noor Hazman bin (2009) Study on CO2 Corrosion in Oil Producing Well. [Final Year Project] (Unpublished)

Mansor, Muhammad Fadhil (2013) NATURAL CONVECTION HEAT LOSS IN BUILDINGS. [Final Year Project] (Unpublished)

Mariapan, Kohila (2013) Sludge Calorific Value Mapping and Potential Energy Recovery for Malaysia. [Final Year Project] (Unpublished)

Marimuthu, Jeevaneswary (2011) Experimental Studies on the Effect of the Particle Shape and Distributor Blade Overlap Angle on the Bed Pressure Drop in a Swirling Fluidized Bed. [Final Year Project] (Unpublished)

Marjono, Nurulain (2008) Determination of Stress Intensity Factor for Arc-shaped Tension Specimen by Using Finite Element Analysis. [Final Year Project] (Unpublished)

Marwan Mohamed Fathi Sayed Khatab, Marwan Mohamed (2011) Effect of Fuel Additives on the Performance and Emissions of an Internal Combustion Engine. [Final Year Project] (Unpublished)

Mas'od, Muhammad Azlan (2011) Powder Metallurgy Processing of Aluminum Matrix Reinforced with Carbon Nanoubes. [Final Year Project] (Unpublished)

Masa Alogo Bindang, Manuel (2008) Investigation of the Environmental Effects on Adhesives Bonded Joints. [Final Year Project] (Unpublished)

Mashal, Al-afnaan (2015) Failure Mode Effect Analysis (FMEA) on Heat Recovery Steam Generator (HRSG): Water Tube Boiler. [Final Year Project] (Unpublished)

Masipa, Karabo (2015) Hot Corrosion Behavior of Thermal Spray Coating. [Final Year Project] (Unpublished)

Masmaliza Binti Zolkefli, Masmaliza (2010) An Investigation Into Abrasive Resistance of Aluminum 6063, Stainless Steel 316 And Mild Steel Using Taber Linear Abraser And Taber Rotary Abraser. [Final Year Project] (Unpublished)

Masood, Rizwan (2017) Theoretical Simulation and Parametric Optimization of Parabolic Through Solar Steam Generation System Under Tropical Climate. Masters thesis, Universiti Teknologi PETRONAS.

Masrah, Mohammad Fadhil (2015) Life Prediction Model of Mechanical Seal Used In Offshore Installation. [Final Year Project] (Submitted)

Mastuki, Nabilah (2011) A STUDY OF ACETIC ACID ROLE IN C02 CORROSION. [Final Year Project] (Unpublished)

Mat, Mohamad Nur Hidayat (2014) Effects of Dust Accumulation on the Efficiency of Solar PV Panels in Malaysia. [Final Year Project] (Unpublished)

Mat Arifin, Arief Farhan (2020) Experimental investigation of open loop thermosyphoning in evacuated tube receiver under varying heat flux. [Final Year Project] (Submitted)

Mat Din, Mohd Safwan (2015) Dynamics Of Rotor Supported By Magnetic Bearing. [Final Year Project] (Unpublished)

Mat Ghani, Normanisah (2012) Experimental Investigation of Natural Convection from Pinned Plate Solar Absorber. [Final Year Project] (Unpublished)

Mat Isa, Mohd Shuhaimi (2004) Study the Failure of Steam Trap of PETRONAS Penapisan Melaka Sdn. Bhd (PPMSB). [Final Year Project] (Unpublished)

Mat Nasir, Mohamad Faiz (2008) Cavitation Failure of Local Made Propellers and Suggestion for Improvement. [Final Year Project] (Unpublished)

Mat Rodzi, Mohamad Syafik (2022) Force Extraction Analysis of an Ocean Kinetic Energy Converter. [Final Year Project] (Submitted)

Mat Saad, Muhammad Najib Bin (2009) Risk Based Inspection Study on Relief Valves at Offshore and Onshore Plant. [Final Year Project] (Unpublished)

Mat Salleh, Siti Nur Hidayah (2008) The Effect of Multiple-use of Polystyrene Cups on Styrene Monomer Migration. [Final Year Project] (Unpublished)

Mat Shayuti, Muhammad Shafiq (2008) The Effect of High Temperature on Styrene Monomer Migration from Polystyrene. [Final Year Project] (Unpublished)

Mat Tasir, Muhammad Hakim (2016) OPTIMAL DESIGN OF HELICAL COMPRESSION SPRINGS. [Final Year Project] (Submitted)

Mat Zuki, Ikhwan Solihin (2009) Simulation of Flow around a Bus with Passive Drag Reduction Attachments. [Final Year Project] (Unpublished)

Matlan, Mohd Joharif (2017) Metallurgical and Mechanical Study of Dissimilar Friction Stir Welding of Carbon Steel and Stainless Steel. [Final Year Project] (Submitted)

Mazhanash, Haziq Asiad (2015) Efficient Water Recycling Through Solar Distillation. [Final Year Project] (Unpublished)

Mazlan, Nur Diniey Nadhirah (2022) Development of Excel-Based RBI Model for Stress Corrosion Cracking. [Final Year Project] (Submitted)

Mazlan, Azri Izwan (2008) Characterization and Properties of Copper and Carbon Powders Mixture. [Final Year Project] (Unpublished)

Mazlan, Luqman Hakim (2020) Coefficient of Performance (COP) evaluation of electric water-cooled chiller during partial/full load operation at PUTRAJAYA plant 1. [Final Year Project] (Submitted)

Mazlan, Mohamad Haiqal (2013) DESIGN AND COMPARITIVE THERMAL ANALYSIS OF CONSTRUCTAL COOLING CHANNEL. [Final Year Project] (Unpublished)

Mazlan, Mohamad Haiqal (2013) DESIGN AND COMPARITIVE THERMAL ANALYSIS OF CONSTRUCTAL COOLING CHANNEL. [Final Year Project] (Unpublished)

Mazlan, Mohamad Mizal Saiful Anuar (2016) Process Parameters Optimization of High Density Polyethylene (HDPE) Friction Stir Welded Plates. [Final Year Project]

Mazlan, Muhamad Muaz (2013) Vibration control of rotor-shaft system with electromagnetic exciter. [Final Year Project] (Unpublished)

Mazlan, Muharnad Muhaidi (2011) Wear investigation of elastically similar sliding bodies material. [Final Year Project] (Unpublished)

Mazlan, Nur Nadhirah (2014) Developing Centrifugal Compressor Performance Predicting Tool For Health Monitoring. [Final Year Project] (Unpublished)

Mazreen bt Mohd Razali, Mazreen (2009) Fitness for Service of Corroded Pressure Vessel. [Final Year Project] (Unpublished)

Mazuan Bin Ibrahim, Mazuan (2010) Design And Fabrication Of A Simple Vehicle For Competition In Shell Eco- Marathon 2010 (Vehicle Frame And Body Design). [Final Year Project] (Unpublished)

Md Arif, Muhammad Nafiz Izzat (2016) Investigation Of The Critical Features Affecting The Condition Of Oil And Gas Pipeline. [Final Year Project] (Submitted)

Md Dewa, Emier Helmee (2008) Redesign and Fabrication of a Mechanical Seal for Pumps. [Final Year Project] (Unpublished)

Md Din, Mohd Hazwan (2008) Study on Automotive Driveline System with Torque Converter Clutch under Harmonically Varying Normal Load. [Final Year Project] (Unpublished)

Md Fadhli Helmi B Noor Kamaruzaman, Md Fadhli Helmi (2008) Design of Submerged Wave-Induced Forcing Elements to Power a Linear Generator. [Final Year Project] (Unpublished)

Md Jaedan, Mohd Sahrul (2008) OPTIMIZATION OF CATHODE WASTE MATERIALS ON EPOXY BASED CONDUCTIVE PAINT PROPERTIES. [Final Year Project] (Unpublished)

Md Nasser, Muhamad Faris Ashraf (2014) Characterization of Rag Layer Formed by Actual Crude Oil, Synthetic Microcrystalline Wax and Synthetic Macrocrystalline Wax. [Final Year Project] (Unpublished)

Md Noor, Muhammad Aimran (2017) The Effect of Cutting Speed on the Machinability During Drilling D2 Hardened Steel. [Final Year Project]

Md Safian, Nurul Aizad (2011) Powder Metallurgical Processing of Aluminium Metal Matrix Composites Reinforced with Graphite. [Final Year Project] (Unpublished)

Md Suhaimy, Ahmad Syafiq (2009) The Effect of Gypsum on the Performance of Intumescent Coating. [Final Year Project] (Unpublished)

Md Yudin, Ahmmad Shukrie Bin (2009) Air-Fin Coil Performance as a Function of Tube Layout. [Final Year Project] (Unpublished)

Md Yunus, Yusheila (2008) Hybrid Solar Dryer with Biomass Integration. [Final Year Project] (Unpublished)

Md Yusof, Mohd Norzahidi (2008) Design and Development ofClothes Drying Closet Using Solar Energy. [Final Year Project] (Unpublished)

Md Yusoff, Ahmad Sofwan (2012) Mechanical and Physical Properties of Titanium Alloy Ti6Al4V-2Y. [Final Year Project] (Unpublished)

Md Zuki, Mohamad Hanif Hazrin (2012) Mechanical and Physical Properties of Titanium Alloy Ti6Al4V-7Y. [Final Year Project] (Unpublished)

Md. Ibrahim, Nor Nurulhuda (2016) Diffusion Bonding and Post-Bond Heat Treatment of Sialon-Nitrided AISI 420 Stainless Steel. Doctoral thesis, Universiti Teknologi PETRONAS.

Md. Tahir, Norazliza (2005) Heat exchanger modeling by neural network optimization for PETRONAS Penapisan Melaka Sdn. Bhd. (PPMSB) crude preheat train / By Norazliza Binti Md. Tahir, TJ 263 .N822 2005. [Final Year Project]

MdYunus, Ahmad Faiz (2013) COMPARATIVE STUDY ONMANUFACTURING PROCESSES OFA SWIRLER CASING. [Final Year Project] (Unpublished)

Megat Atif Bin Megat Shahair, Megat Atif (2008) Application of Weibull Probability to Predict the Size of Inclusion in Metallic Material. [Final Year Project] (Unpublished)

Megat Iskandar, Megat Amirul Adli (2020) Numerical Study of Topology Optimization of Jacket Platform: A Review. [Final Year Project] (Submitted)

Megat Shahair, Megat Atif (2008) Application ofWeibull Probability to Predict the Size of Inclusion in Metallic Material. [Final Year Project] (Unpublished)

Memon, Zeeshan (2019) Experimental Investigation of Two- Phase Separation in a T-Junction with Combined Diameter Ratio. Masters thesis, Universiti Teknologi PETRONAS.

Mengal, Ali Nawaz (2016) Mechanical Properties of Basalt-Carbon/Epoxy Hybrid Laminated Composite for Wind Turbine Rotor Blades. Doctoral thesis, Universiti Teknologi PETRONAS.

Me’eraj, Abdul Rasyid (2020) Risk Analysis of Domino Effect Due to Fire in Petroleum Plants. [Final Year Project] (Submitted)

Mhd Nasser, Asma‘ Khairunnisa‘ (2016) Development of Excel-Based Piping Vibration Assessment Model. [Final Year Project] (Submitted)

Min, Teow Jing (2015) CFD study on Energy Promoter insertion for drag reduction in oil pipelines. [Final Year Project] (Unpublished)

Minhat, Mizuan (2011) Development of Spark Electrode for an Explosion Vessel. [Final Year Project] (Unpublished)

Minzhao, Liew (2017) The Study of Heat Transfer Enhancement of Solar Air Heater Using airfold Extended Surface. [Final Year Project]

Misnan, Mohd Hamizan Muqri (2021) CFD MODELLING OF MOISTURE SEPARATION IN INLINE SEPARATOR. [Final Year Project] (Submitted)

Misren, Muhammad Mokri (2014) Reliability, Availability and Maintainability Analysis for Main Oil Line Pump by Dominant Failure Modes. [Final Year Project] (Unpublished)

Mizwa Anuar Bin Mat Tahir, Mizwa Anuar (2010) Mathematical Modelling and Simulation of Petrochemical Processes. [Final Year Project] (Unpublished)

Moayelfar, Majid (2017) Patient-specific Metallic Femoral Component using Incremental Sheet Forming. Doctoral thesis, Universiti Teknologi PETRONAS.

Mohamad, Wan Farhana (2013) Development of Mineral Based Intumescent Fire Retardant Coating for Structural Applications. Masters thesis, Universiti Teknologi PETRONAS.

Mohamad, Ahmad Ikram (2015) Correlation between Microstructure and Microhardness of Nitrided Austenitic Stainless Steel. [Final Year Project] (Unpublished)

Mohamad, Maaruf (2009) STUDY OF MICROSTRUCTURE AND CHEMICAL PROPERTIES OF BARNACLES GROW AT EXTERNAL SURF ACE OF PIPELINES. [Final Year Project] (Unpublished)

Mohamad @ Rusdi, Muhammad Faez Ezanee (2016) Simulation and Modelling of a Gas Separation System. [Final Year Project] (Submitted)

Mohamad Ali, Ikhwan Hakim (2022) Characteristics of Dust Accumulation and Influence on PV Panel’s Efficiency. [Final Year Project] (Submitted)

Mohamad Amin Zikri bin Mohamad Fauzi, Mohamad Amin Zikri (2011) New Blended Cement for Oil-Well Application. [Final Year Project] (Unpublished)

Mohamad Amir Ridzwan B Mansor , Mohamad Amir Ridzwan (2008) The Design of Mechanisms for Gantry Crane Experimental Rig. [Final Year Project] (Unpublished)

Mohamad Amirul bin Mohamad Yusuf, Mohamad Amirul (2010) Stress Intensity Factor for a Crack Emanating from a Corner of a Square Hole. [Final Year Project] (Unpublished)

Mohamad Basri, Mohamad Abid (2011) Simulation of polymer melt during injection molding: Influence of undercooling rates. [Final Year Project] (Unpublished)

Mohamad Fahmi Bin Md Bekery, Mohamad Fahmi (2012) CHARACTERISATION OF INTER-LAMINAR SHEAR STRENGTH (ILSS) OF A RESIN INFUSED WIND TURBINE BLADE POLYMER COMPOSITE. [Final Year Project] (Unpublished)

Mohamad Faiz bin Mat Nasir, Mohamad Faiz (2008) Cavitation Failure of Local Made Propellers and Suggestion for Improvement. [Final Year Project] (Unpublished)

Mohamad Firdaus Bin Ayob, Mohamad Firdaus (2008) Investigation into the Potential of Bio-based Automotive Engine Lubrication Oil Using Tribological Test Method. [Final Year Project] (Unpublished)

Mohamad Gazali, Mohamed Zafir (2009) Study of Gas Turbine Blade Impingement Cooling. [Final Year Project] (Unpublished)

Mohamad Hafiz Bin Mohd Hasan Abdullah, Mohamad Hafiz (2010) Thermal Mechanical Simulation of Corner Joint Configuration. [Final Year Project] (Unpublished)

Mohamad Haniff Bin Zamahsari, Mohamad Haniff (2010) Studies And Simulations Of Semi-Active Vehicle Suspension System. [Final Year Project] (Unpublished)

Mohamad Hasrul Hilmi b. Khairul Aman, Mohamad Hasrul Hilmi (2010) Risk-Based Inspection – Flyash Erosion on Boiler Tube at Coal-Fired Power Plant. [Final Year Project] (Unpublished)

Mohamad Ikhwan Bin Kori, Mohamad Ikhwan (2010) Study, Analysis and Implementation of Air-Fuel Ratio Control on Perodua Viva for Better Fuel Consumption. [Final Year Project] (Unpublished)

Mohamad Iqmal bin Nizamuddin, Mohamad Iqmal (2009) Design A Solar Parabolic Water Heater System For Absorption Refrigeration of the Zero-Energy Terrace House. [Final Year Project] (Unpublished)

Mohamad Iskandar Bin Mahbob, Mohamad Iskandar (2010) Study Of Calcium Ions Effect On Pitting Corrosion Using Electrochemical Noise Analysis (Ecn). [Final Year Project] (Unpublished)

Mohamad Ismol, Mohamad Ismail (2017) INVESTIGATION ON THE EFFECTIVENESS OF NITROGEN GAS FOR SURFACE NITRIDING OF INTERNAL PIPE SURFACE EROSION. [Final Year Project]

Mohamad Izham Bin Mohamad Zainal, Mohamad Izham (2010) Dynamic Load Analysis of the Micro Unmanned Aerial Vehicle (UAV)Structure. [Final Year Project] (Unpublished)

Mohamad Kamal, Siti Aisyaitun Fairuz (2022) Thermodynamic Analysis of Municipal Solid Waste Plasma Gasification Using Different Gasification Agents. [Final Year Project] (Submitted)

Mohamad Kamal Ruzaini Bin Mohd Afifi, Mohamad Kamal Ruzaini (2010) Mechanical and Water Absorption Properties of Oil Palm Empty Fruit Bunch Reinforced Polyethylene Composites. [Final Year Project] (Unpublished)

Mohamad Lawi, Muhammad Fawwaz (2014) The Structural Dynamics of Nitrided Ferritic 439 Grade Stainless Steel Plates. [Final Year Project] (Unpublished)

Mohamad Lutfi, Mohamad Ashraf (2016) Effects of Ball Milling Time on the Fire Performance Red Mud Intumescent Coating. [Final Year Project] (Submitted)

Mohamad Lutfi, Mohamad Ashraf (2016) Effects of Ball Milling Time on the Fire Performance Red Mud Intumescent Coating. [Final Year Project] (Submitted)

Mohamad Mohaimin bin Mokhlis, Mohamad Mohaimin (2011) Design and Fabrication of Drive Train System for Bosch Power Tools Cordless Race 2011. [Final Year Project] (Unpublished)

Mohamad Najib Bin Mohtar, Mohamad Najib (2008) Developing Carbon Particle Reinforced Aluminium Composite by Powder Metallurgy. [Final Year Project] (Unpublished)

Mohamad Nashakir bin Md Dom, Mohamad Nashakir (2011) Reliability Block Diagram Assessment of Ethylene Oxide Production Facilities. [Final Year Project] (Unpublished)

Mohamad Noor, Mohd Ruzaini (2008) Optimizing Heat Insulation of a Solar Oven. [Final Year Project] (Unpublished)

Mohamad Noor, Wan Aizat (2020) The Study of Magneto-Active Polymer Composite Physiochemical Characteristics Using Petroleum Based Oil as a Dispersing Aid. [Final Year Project] (Submitted)

Mohamad Refaee, Mohd Ashraf Arif (2011) Finite Element Analysis for a Knuckle Crane Boom. [Final Year Project] (Unpublished)

Mohamad Rozi Bin Sulaiman , Mohamad Rozi (2011) PERFORMANCE EVALUATION MODELING OF PRE-TREATMENT UNIT IN GAS PROCESSING PLANT. [Final Year Project] (Unpublished)

Mohamad Shiham, Najwa Sofwani (2012) ANALYSIS ON PROCESS PARAMETERS OF SLS RAPID PROTOTYPING PROCESS. [Final Year Project] (Unpublished)

Mohamad Suhaimi Bin Yahaya, Mohamad Suhaimi (2010) Management, Selection, Design and Installation of the running chassis (steering system) and accessories of a simple vehicle for competition in Shell Eco- Marathon 2010 - 1. [Final Year Project] (Unpublished)

Mohamad Yasin, Muhammad Hilman (2021) Study of Particle Velocity Impact on The Surface of M-152 Steel and SiCp/Ti- 6Al-4V Metal Matrix Composite. [Final Year Project] (Submitted)

Mohamad Yusoff, Syaza Yasmin (2016) CFD Modeling of Thermoelectric Air Duct System for Cooling of Building Envelope. [Final Year Project] (Submitted)

Mohamad Zaid Bin Harris, Mohamad Zaid (2009) Design and Development of Low Temperature Zero Watt Alpha Type Stirling Engine. [Final Year Project] (Unpublished)

Mohamad Zaki, Putera Nazreen Shah (2014) Design and Simulation of SmartBall for Pipeline Inspection. [Final Year Project] (Unpublished)

Mohamed, Mohamed Osman Abdalla (2013) Energy Savings and Speed Improvement in Linear Power Hydraulic Actuators Using a Self-Actuated Flow Control Valve. Doctoral thesis, Universiti Teknologi PETRONAS.

Mohamed, Hisyam (2013) COMPUTATIONAL FLUID DYNAMIC MODELLING OF FIRE INCIDENT. [Final Year Project] (Unpublished)

Mohamed, Mohamed Elsadig (2005) Process control system identification/ By Mohamed Elsadig Mohamed, TJ 217.2 .M697 2005. [Final Year Project]

Mohamed, Mohamed Fathelrahman (2009) CFD Analysis of Ribbed Double Pipe Beat Exchanger. [Final Year Project] (Unpublished)

Mohamed, Mohamed Fathelrahman (2009) CFD Analysis of Ribbed Double Pipe Heat Exchanger. [Final Year Project] (Unpublished)

Mohamed Asri, Mohamad Aimran (2021) Performance Simulation of a Free Piston Linear Generator by Using MATLAB Simulink. [Final Year Project] (Submitted)

Mohamed Faiz bin Mohamed Amin, Mohamed Faiz (2008) Designing Air Intake System for Engine Performance and Efficiency Optimisation. [Final Year Project] (Unpublished)

Mohamed Fuad Al Farabi Shazi B Shaarani, Mohamed Fuad Al Farabi Shazi (2008) Design and Implementation of Robofly Wing Flapping Mechanism Using Piezoelectric Crystal. [Final Year Project] (Unpublished)

Mohamed Khalil Bin Mohamed Razif, Mohamed Khalil (2010) Study On Effect Of Nanosilica Sand Addition On Physical And Mechanical Properties Of Alumina Powder. [Final Year Project] (Unpublished)

Mohamed Khatab, Marwan (2011) Effect of Fuel Additives on the Performance and Emissions of an Internal Combustion Engine. [Final Year Project] (Unpublished)

Mohamed Nawai, Rahimah (2011) Computational Fluid Dynamics (CFD) Study of Flow Development in an Eccentric Annulus. [Final Year Project] (Unpublished)

Mohamed Nizan, Amir Afiz (2008) HUMAN TRANSPORTER (E-Porter). [Final Year Project] (Unpublished)

Mohamed Razali, Muhammed Raqib bin (2009) Stress Intensity Factor on a Surface Crack of Cylindrical Pressure Vessel. [Final Year Project] (Unpublished)

Mohamed Saad, Ahmed (2010) FLOW ANALYSIS OF OVERTAKING VEIDCLES: CFD STUDY. [Final Year Project] (Unpublished)

Mohamed Said Shahat Ahmed El-Khatib, Mohamed Said Shahat (2009) Absorption and Desorption of Hydrogen in Metal Hydrides. [Final Year Project] (Unpublished)

Mohamed Talaat, Mohamed Farid (2015) Conceptual Development of non-conventional steam turbine. [Final Year Project] (Unpublished)

Mohamed Termizi, Noor Aniza (2016) Thermogravimetric Kinetic Analysis and Characterization of Poultry Processing Dewatered Sludge. Masters thesis, Universiti Teknologi PETRONAS.

Mohamed Yunus, Mohmed Azman (2016) Simulation of Parabolic Trough Collector (PTC) for Direct Steam Generation (DSG) under Malaysia Weather. [Final Year Project] (Submitted)

Mohamed Yusoof, Mohamed Zaid (2012) Finite Element Analysis on Residual Stresses Occur in Heat Affected Zone (HAZ) of the Carbon Steel Welded Pipe. [Final Year Project] (Unpublished)

Mohamed Zafir Bin Mohamad Gazali, Mohamed Zafir (2009) Study of Gas Turbine Blade Cooling. [Final Year Project] (Unpublished)

Mohammad Amer Qais Abro, Amer (2010) Computational Fluid Dynamics Study Of Airflow Throw A Car’s Radiator. [Final Year Project] (Unpublished)

Mohammad Asyraf bin Mohammad Hatta, Mohammad Asyraf (2008) Engine Testing of Gasoline and E5, E10, E15 and E20 Ethanol Blends. [Final Year Project] (Unpublished)

Mohammad EL Hafiz bin Mushadad, Mohammad EL Hafiz (2012) Investigation into Resin Infusion Strategies in the Fabrication of GRE Composite Wind Turbine Blade. [Final Year Project] (Unpublished)

Mohammad Hatta, Mohammad Asyraf (2008) Engine Testing of Gasoline, ES, ElO, E15 and E20 Ethanol Blends. [Final Year Project] (Unpublished)

Mohammad Izani, Nik Mohd Hakim (2016) Analysis and Simulation of PDC Drill Bit Design In Mitigating Stick and Slip. [Final Year Project] (Submitted)

Mohammad Izzatul Akmal Bin Abdillah, Mohammad Izzatul (2012) Experimental Study on Spur Gear Vibration Characteristics under Various Loading Conditions. [Final Year Project] (Unpublished)

Mohammad Latpi, Aliff Idham (2013) ENDURANCE INVESTIGATION OF NITRIDE FERRITIC STAINLESS STEEL SS439 UNDER TORSIONAL LOADING. [Final Year Project] (Unpublished)

Mohammad Nazari, Najat (2023) Mtgs And Methods For Assessing Lubrication Oil Parameters For Degradation Prediction. Masters thesis, Universiti Teknologi PETRONAS.

Mohammad Noor, Mohd Amri (2013) Offshore Pipeline Reliability Assessment Using Degradation Analysis and P-F Interval Model. [Final Year Project] (Unpublished)

Mohammad Noor Bin Md Yassin, Mohammad Noor (2010) The Effect Of Pre-Tinning Process With Respect To Gold Embrittlement Issue For Gold Plated Pins. [Final Year Project] (Unpublished)

Mohammad Pour, Ehsan (2013) Numerical and Experimental Evaluation of Carbon Nanotube/Polypropylene Composites Using Nonlinear Finite Element Modeling. Doctoral thesis, Universiti Teknologi PETRONAS.

Mohammad Rabeek, Mohamed Tawfeek (2016) Development of a Model to Predict the Global Solar Radiation Using Statistical Techniques. [Final Year Project] (Submitted)

Mohammad Rafi, Mohammad Syafiq (2016) Aerodynamic Analysis on Small Race Car Body by using CFD Simulation. [Final Year Project] (Submitted)

Mohammad Safaruddin, Muhammad Izwan (2011) Failure Analysis and Modification Analysis for the Seal Face in Mechanical Seal. [Final Year Project] (Unpublished)

Mohammad Sollehuddin Bin Sabtu, Mohammad Sollehuddin (2010) Development of Alternative Fuel Briquettes from Poultry Processing Waste (Energy Content and Chemical Characteristic). [Final Year Project] (Unpublished)

Mohammad Zakuan bin Ahmad, Mohammad Zakuan (2011) Numerical Stress Analysis of Selected Materials in Solid Expandable Tubular Repair for Casing Damaged Well. [Final Year Project] (Unpublished)

Mohammad Zuhairi bin Ramly, Mohammad Zuhairi (2008) The Design and Fabrication of a prototype machine: “asam gelugor” processing machine. [Final Year Project] (Unpublished)

Mohammad `Izzat Bin Mohd Radzi, Mohammad `Izzat (2009) Effect of Clay (Vermiculite) as Reinforcement in Mechanical Properties Epoxy Matrix Composite Materials. [Final Year Project] (Unpublished)

Mohammed, Badrulzzaman (2013) Nitriding of AISI 316L Austenitic Stainless Steel at Low Temperature for the Enhancement of Surface Properties and Corrosion Properties. [Final Year Project] (Unpublished)

Mohammed Al-Hashimy, Zahid Ibrahim (2016) Experimental and Numerical Investigation on the Vibrations Induced by Slug Flow Interaction with Horizontal Pipe Structure. Doctoral thesis, Universiti Teknologi PETRONAS.

Mohammed Ashraf, Atif (2011) Enhanced Removal of Nickel (II) Ions from Synthetic Wastewater employing Fixed Bed Ion Exchange Column Technique. [Final Year Project] (Unpublished)

Mohanad Said Abdel Salam, Mohanad Said Abdel Salam (2010) Micro Aerial vehicle: Experimental Aerodynamics optimization. [Final Year Project] (Unpublished)

Mohd Abd Ghafar, Mohd Afiq (2008) Feasibility Study on Possibility of Using Flare Gas as a Source of Energy. [Final Year Project] (Unpublished)

Mohd Afandi, Nurfanizan (2011) Development of a System for Cooling Inlet Air for Gas Turbine using Fogging System. [Final Year Project] (Unpublished)

Mohd Aiman Bin Ismail, Mohd Aiman (2008) Microstructure Characterization of Creep-Tested Reformer Tube Material. [Final Year Project] (Unpublished)

Mohd Aiman bin Kamaru zaman, Mohd Aiman (2010) Effects of Process Parameters on Strength of Swept Friction Stir Spot Welded Plate. [Final Year Project] (Unpublished)

Mohd Aizat bin Mohd Nordin, Mohd Aizat (2009) Analysis of the Dynamic Interference between Stator and Rotor of a Refrigeration Compressor Motor by using Finite Element Method. [Final Year Project] (Unpublished)

Mohd Aizzat Bin Omar, Mohd Aizzat (2010) The Development of Thermal Insulation from Oil Palm Waste Material. [Final Year Project] (Unpublished)

Mohd Akmal Bin Mohd Sobli, Mohd Akmal (2008) Spray Characteristic by using Phase Doppler Anemometry (PDA) and Laser Doppler Anemometry (LDV). [Final Year Project] (Unpublished)

Mohd Ali, Munirah (2008) Design & Development of Lab Scale Latent Heat Energy Storage Equipment using Paraffin Wax. [Final Year Project] (Unpublished)

Mohd Ali, Syazwani (2016) Studying the Parameters Which Affect Sprinkler Fire Protection System Performance in Buildings. [Final Year Project] (Submitted)

Mohd Alif Syazwan bin Mohd Nasir, Mohd Alif Syazwan (2008) Experimental Modelling of the Fluid Flow in a Furnace Top of an Ethane Cracker in EPEMSB, Paka. [Final Year Project] (Unpublished)

Mohd Aliff Omar bin Haris, Mohd Aliff Omar (2010) Micro Wind Turbine as the Power Supply for Micro Unmanned Aerial Vehicle. [Final Year Project] (Unpublished)

Mohd Amirul Bin Che Hussain, Mohd Amirul (2012) Mechanical Design and Dynamic Analysis of Pipe Crawling Robot for 6” to 10” diameter Internal Gas Pipeline Inspection. [Final Year Project] (Unpublished)

Mohd Amirul Hakim Bin Sulaiman, Mohd Amirul Hakim (2008) Banana Trunk As A Lost Circulation Material In Hydrocarbon Drilling Fluid. [Final Year Project] (Unpublished)

Mohd Amirul Mukminin bin Alias, Mohd amirul (2011) Study of Adhesive Strength in Polymer Plate Heat and Mass Exchanger. [Final Year Project] (Unpublished)

Mohd Amran, Ahmad Firdaus (2022) Establishing Maintenance Planning for Solar Power Plant based on RAM Study. [Final Year Project] (Submitted)

Mohd Anuar, Nurul Alia (2011) STRESS ANALYSIS OF UNDERWATER PIPELINE FOR IRREGULAR SEABED TOPOGRAPHY USING CAESAR II. [Final Year Project] (Unpublished)

Mohd Arif, Muhammad Nor Hakim (2013) Mechanical Design and Dynamic Analysis of Pipe Crawling Robot for Internal Gas Pipeline Inspection. [Final Year Project] (Unpublished)

Mohd Ariff Bin Mohd Tahir, Mohd Ariff (2010) Comparative Study of Polyurea and Epoxy Protective Coating via Salt Spray. [Final Year Project] (Unpublished)

Mohd Arshad, Mohamad Hazrul Azli (2016) The Study of the Effects of Drilled Hole on Tensile Strength of Hybrid Fiber Reinforced Epoxy (HFRE) Composite. [Final Year Project] (Submitted)

Mohd Ashraf Arif b. Mohamad Refaee, Mohd Ashraf (2011) Finite Element Analysis for a Knuckle Crane Boom. [Final Year Project] (Unpublished)

Mohd Asmadi, Mohd Amir (2015) Development of a Red Mud-Epoxy Intumescent Coating for Steel Structures. [Final Year Project] (Unpublished)

Mohd Asri, Nur Aqillah (2022) Artificial Neural Network of Flow Boiling Heat Transfer in Straight Pipe with Metal Foam. [Final Year Project] (Submitted)

Mohd Asri, Ahmad Fuad (2021) Diagnosability Evaluation of Mechanical Systems Design Using Data Analysis. [Final Year Project] (Submitted)

Mohd Asri, Muhammad Izzudin (2021) Material Flow Modelling During Friction Stir Welding (FSW) Process Using Smooth-Particle Hydrodynamics (SPH) Method. [Final Year Project] (Submitted)

Mohd Assri, Muhammad Amirul Aiman (2021) Mechanical Properties Investigation of Ti-6Al-7Nb as an Alternative Biomedical Tools. [Final Year Project] (Submitted)

Mohd Atiqullah bin Che Ghazali, Mohd Atiqullah (2011) Study on Drilling Fluid Using Electrical Capacitance Tomography (ECT). [Final Year Project] (Unpublished)

Mohd Azahari bin Mohamed Buang, Mohd Azahari (2010) Study of PWHT Microstructures and Mechanical Properties for Mild Steel and SA106B Pipe Material. [Final Year Project] (Unpublished)

Mohd Azhan Bin Hasbullah, Mohd Azhan (2009) Comparison of different cross-sectional cooling channels for better heat dissipation. [Final Year Project] (Unpublished)

Mohd Azid, Nurul Fathonah (2021) Experimental Investigation of Solar Vortex Power Generation System Integrated with Sensible Heat TES. [Final Year Project] (Submitted)

Mohd Aziman Bin Azemi, Mohd Aziman (2008) Failure Analysis of Heat Exchanger’s Tubes at GPP Kerteh. [Final Year Project] (Unpublished)

Mohd Azmi, Muhamad Aizat Syafiq (2016) NITRIDING OF 2205 DUPLEX STAINLESS STEELS TO ENHANCE CORROSION RESISTANCE. [Final Year Project] (Submitted)

Mohd Azmi Bin Hayat, Mohd Azmi (2010) The Study of Sandpapering Effect on Mechanical Properties of Aircraft Materials (Aluminum Alloy and Carbon Fiber Reinforce Plastic). [Final Year Project] (Unpublished)

Mohd Azmir, Faiqah (2014) Novel Method to Join Aluminum With Nylon. [Final Year Project] (Unpublished)

Mohd Aznan, Md Nasrun Faris (2012) Characterization of Solid Biomass Fuel Briquettes. [Final Year Project] (Unpublished)

Mohd Azra'in Zainuddin, Mohd Azra'in (2009) Study og Engine Performance when Using Ethanol as Blended Fuel For Spark Ignition Engine. [Final Year Project] (Unpublished)

Mohd Azra’in Zainudin , Mohd Azra’in (2009) Study Of Engine Performance When Using Ethanol As Blended Fuel For Spark Ignition Engine. [Final Year Project] (Unpublished)

Mohd Azrul Amin B Kimin, Mohd Azrul Amin (2008) Preliminary Design Of Palm Oil Frond Gasifier. [Final Year Project] (Unpublished)

Mohd Azrul bin Samsuddin, Mohd Azrul (2010) Experimental & Numerical Investigation on the effect of inlet shape of inclined heated channel. [Final Year Project] (Unpublished)

Mohd Azuan Bin Mohamad Nor, Mohd Azuan (2008) Study And Development Of Pellet Fuel From Oil Palm Frond. [Final Year Project] (Unpublished)

Mohd Azuan bin Mohd Azlan, Mohd Azuan (2009) Design of Composite Stairs in UTP Academic Blocks. [Final Year Project] (Unpublished)

Mohd Badaruddin Bin Mahmod, Mohd Badaruddin (2010) Simulation of Rotating Seal Ring. [Final Year Project] (Unpublished)

Mohd Badruddin bin Karim, Mohd Badruddin (2009) The Effect of Thermal Aging to The Impact Properties of Glasss Fiber Reinforced Epoxy. [Final Year Project] (Unpublished)

Mohd Bahrin, Nurinfaqihah (2022) Using Reliability Growth Model to Predict New Covid-19 Cases in Malaysia. [Final Year Project] (Submitted)

Mohd Burhan, Muhammad Izqandar (2021) ROTOR DYNAMIC DIAGNOSTICS USING FINITE ELEMENT ANALYSIS. [Final Year Project] (Submitted)

Mohd Burhanuddin Bin Ruslan, Mohd Burhanuddin (2010) Comparative Study on Environmental Impacts of Grocery Bags through LCA. [Final Year Project] (Unpublished)

Mohd Dzulfikry Bin Mohd Aris, Mohd Dzulfikry (2010) Design and Analysis of Robotic Device for Cleaning Window Glass Panel in High Rise Building. [Final Year Project] (Unpublished)

Mohd Eazaq Farommi Bin Hamat, Mohd Eazaq (2008) Evaporative Cooler As an Air Inlet Treatment Of Gas Turbine. [Final Year Project] (Unpublished)

Mohd Eilham, Mohamad Anis (2016) Study on Low Boost Pressure Effect of Electric Turbocharger on Engine Performance. [Final Year Project] (Submitted)

Mohd Erzo Bin Mohamad Sharip, Mohd Erzo (2009) Corrosion Prevention of Carbon Steel Using Tapioca Polysaccharides – Based Coating. [Final Year Project] (Unpublished)

Mohd Fadhlan bin Ismail, Mohd Fadhlan (2008) Stress Concentration Factors at Two Radial Adjacent Nozzle-Header Connections of a Cylindrical Pressure Vessel. [Final Year Project] (Unpublished)

Mohd Fahmi Abdul Rahim, Mohd Fahmi (2009) Wind load effect on train station. [Final Year Project] (Unpublished)

Mohd Fairozlan Bin Ahmad Tarmizi, Mohd Fairozlan (2008) Total Productive Maintenance Assessment on Discrete Manufacturing System. [Final Year Project] (Unpublished)

Mohd Faisal Bin Ab Ghani, Mohd Faisal (2009) Development of An Experimental Gantry Crane Rig. [Final Year Project] (Unpublished)

Mohd Faiz bin Ahmad Shahrom, Mohd Faiz (2009) Design and Development of Thermal Energy Storage (TES) Tank. [Final Year Project] (Unpublished)

Mohd Faiz bin Sofian, Mohd Faiz (2009) Study on Hydrogen-On-Demand (HOD) System. [Final Year Project] (Unpublished)

Mohd Faizal Bin Muhamad Tajudin, Mohd Faizal (2010) Study On The Hardness And Microstructure Properties Of Nitrided Ferritic Stainless Steel Powder After Sintering. [Final Year Project] (Unpublished)

Mohd Faizal Din Chan, Irwan (2004) Light Rail Transit (LRT) Brake Materials: Detail Characterization of Hardness and Impact Energy. [Final Year Project] (Unpublished)

Mohd Faizal Din Chan, Mohd Naquib (2008) Vibration Isolation of Floating Raft System. [Final Year Project] (Unpublished)

Mohd Fasya b. Ramsah, Mohd Fasya (2008) Characterization and Properties of Nickel Powder and Carbon Powder Mixture. [Final Year Project] (Unpublished)

Mohd Fathi Bin Ismail, Mohd Fathi (2010) The Tribological Study On Polymer Matrix Composite Using Pin On Disc Testing Technique. [Final Year Project] (Unpublished)

Mohd Faudzi, Mohamad Faeesol (2021) Development of Tracking Signal for Non-homogeneous Poisson Process Model. [Final Year Project] (Submitted)

Mohd Fauzi bin Yean, Mohd Fauzi (2011) Synthesis and Characterization of Acetate Based Ionic Liquid for CO2 Removal. [Final Year Project] (Unpublished)

Mohd Fazril Irfan bin Ahmad Fuad, Mohd Fazril Irfan (2009) Thermal Spray Coating for Corrosion Under Insulation Prevention. [Final Year Project] (Unpublished)

Mohd Fikram Bin Mat Yazid, Mohd Fikram (2008) Development of a Failure Prediction Model for Heat Exchanger Tube. [Final Year Project] (Unpublished)

Mohd Firdaus B Sapidih, Mohd Firdaus (2009) Lift Force Analysis on Australian Aboriginal Boomerang of Several Design Variations Parameters. [Final Year Project] (Unpublished)

Mohd Fithri Azad Bin Abul Kalam Azad, Mohd Fithri Azad (2011) Piping Inspection Monitoring Strategy. [Final Year Project] (Unpublished)

Mohd Fozi, Muhammad Ariffullah (2015) Effect of Vibration on Human Body. [Final Year Project] (Submitted)

Mohd Ghazali, Ahmad Nadiy (2009) Development of a Computer Programto Assess Gas Compressor Performance. [Final Year Project] (Unpublished)

Mohd Ghazi, Nurhafiza (2011) Effect of Nitriding Temperature on Duplex Stainless Steel. [Final Year Project] (Unpublished)

Mohd Hafizuddin Bin Hashim, Mohd Hafizuddin (2011) FINITE ELEMENT SIMULATION OF RESIDUAL STRESSES IN COLD-EXPANDED PLATE. [Final Year Project] (Unpublished)

Mohd Haidzir Bin Anuar, Mohd Haidzir (2010) Studies & Simulation Of Train Suspension System. [Final Year Project] (Unpublished)

Mohd Hanis B Mohd Daud, Mohd Hanis (2010) Thermo-Mechanical Modeling Of Friction Stir Welded Plate. [Final Year Project] (Unpublished)

Mohd Hashim, Mohamad Haziq Faiz (2013) INVESTIGATING THE EFFECT OF COIL PLATES ON THE PERFORMANCE OF FIRE TUBE STEAM PACKAGED BOILER USING SIMULATION SOFTWARE. [Final Year Project] (Unpublished)

Mohd Haziq Bin Ahmad Bakhtiar, Mohd Haziq (2010) Design of a Multidisc Pump for Slurry Transfer. [Final Year Project] (Unpublished)

Mohd Haziq Bin Ahzahar, Mohd Haziq (2009) Design and Fabrication of on Roof Solar Chimney. [Final Year Project] (Unpublished)

Mohd Hazran bin Mat Rahim, Mohd Hazran (2010) Gas Turbine Internal Blade Cooling Study. [Final Year Project] (Unpublished)

Mohd Husairil Bin Ibrahim, Mohd Husairil (2009) Preventive Program for Small Bore Piping Failure At Gas Processing Plant. [Final Year Project] (Unpublished)

Mohd Irsyaduddin bin Ab. Latif, Mohd Irsyaduddin (2009) Design of A Structural Beam for Future UTP Composite Canopy. [Final Year Project] (Unpublished)

Mohd Isa, Ahmad Safwan Bin (2009) Evaluation on Rust Stabilizer Paint for Maintenance Painting of Internal Pipeline. [Final Year Project] (Unpublished)

Mohd Ishak, Muhammad Asroldin (2015) Microstructural Evolution and Physical Properties Changes during Liquid Phase Sintering of Fe-Cu-C Compacts. [Final Year Project] (Unpublished)

Mohd Ismail, Abu Bakar Sidiq (2015) Study on Tensile Strength of SS304 Steel Weld Joint with Different Bevel Angles. [Final Year Project] (Unpublished)

Mohd Izuddin Bin Ismail, Mohd Izuddin (2010) Failure Analysis on Stainless Steel Tubing of a Lube Oil Console for Gas Generator. [Final Year Project] (Unpublished)

Mohd Izwan Hadi b. Ismail @ Mansor, Mohd Izwan Hadi (2008) Parametric Study on Passive Suspension of Light Rail Vehicle (LRV). [Final Year Project] (Unpublished)

Mohd Izwan Hadi b. Ismail @ Mansor, Mohd Izwan (2008) Parametric Study on Passive Suspension of Light Rail Vehicle (LRV). [Final Year Project] (Unpublished)

Mohd Jafri, Mohamad Sharul Affendi (2015) Design and Development of Hybrid Portable Mini Wind Turbine. [Final Year Project] (Unpublished)

Mohd Johari, Muhammad Syafiq (2012) Development of Reliability Model for Furnace System using Spreadsheet. [Final Year Project] (Unpublished)

Mohd Junaidi, Muhammad Hatta (2011) The Study of Tensile Failure on Thin Plate Hybrid Composites with Drilled Hole. [Final Year Project] (Unpublished)

Mohd Kamal, Eliya Farah Hana (2013) Effects of Alkali-Silane Treatment on Tensile Strength of Woven Kenaf Reinforced Polypropylene Composites. [Final Year Project] (Unpublished)

Mohd Kamil Azran bin Md Nadzar, Mohd Kamil Azran (2010) The Effect Of Anti Roll Bar On The Heavy Vehicle Handling. [Final Year Project] (Unpublished)

Mohd Karim, Ariff Hakimy (2016) Design Improvement of Existing Slip-on Sprocket. [Final Year Project] (Submitted)

Mohd Kasim, Muhammad Zulfaqqar (2015) Fatigue Life Analysis of Holed Component in Aircraft Stuctures. [Final Year Project] (Unpublished)

Mohd Khaidi, Mohd Syazwan (2010) Dynamic Analysis and Simulation of Arm Trainer. [Final Year Project] (Unpublished)

Mohd Khairi B. Che Abdullah, Mohd Khairi (2009) Effects of Aerodynamics Changes on A Car Caused by Another in Its Proximity: An Experimental Study. [Final Year Project] (Unpublished)

Mohd Khairuddin, Nadhira (2014) Study on Structural and Hydrodynamics of Autonomous Underwater Gliders. [Final Year Project] (Unpublished)

Mohd Khairul Anuar Bin Zainal Abidin, Mohd Khairul Anuar (2010) The Effect of Resin Viscosity in Vacuum Infusion Process. [Final Year Project] (Unpublished)

Mohd Khairul Izham Bin. Abdul Rahman, Mohd Khairul Izham (2010) Development Of Test Rig For The Study Of The Internal Blade Cooling. [Final Year Project] (Unpublished)

Mohd Khairul Munir B Kamaruzaman, Mohd Khairul Munir (2010) Improvement on Wear Resistance of 316 Austenitic Stainless Steel by High Temperature Nitriding Technique. [Final Year Project] (Unpublished)

Mohd Khalifa Taufiq Kamaruddin, Mohd Khalifa Taufiq (2008) Emergency Power Supply To Start A Car. [Final Year Project] (Unpublished)

Mohd Madzhir b Ibrahim, Mohd Madzhir (2011) Dynamic Characteristics of a Hybrid Composite Drive Shaft for Automotive Application. [Final Year Project] (Unpublished)

Mohd Mohtar, Nurulhusna (2013) Vibration Analysis of Centrifugal Pump. [Final Year Project] (Unpublished)

Mohd Murad, Safwan Hanis (2009) Study ofa New Air Intake System for a Single Cylinder, Fuel Injection, 4 stroke Go-Kart engine. [Final Year Project] (Unpublished)

Mohd Nadzim, Mohd Fathur Rahman (2015) Evaluation of Heat Transfer Performance of Helical Coil Heat Exchanger. [Final Year Project] (Unpublished)

Mohd Naim B. Ruslan, Mohd Naim (2008) Microbiological Influence Corrosion Study on Offshore pipelines. [Final Year Project] (Unpublished)

Mohd Naquib bin Mohd Faizal Din Chan, Mohd Naquib (2008) Vibration Isolation of Floating Raft System. [Final Year Project] (Unpublished)

Mohd Nashriq Bin Zulkefle, Mohd Nashriq (2010) Microstructure Studies on Commercially Available Heat Shrinkable Polymeric Materials. [Final Year Project] (Unpublished)

Mohd Nasihuddin, Wan Mohd Hariri (2009) PRE-DESIGN LATENT HEAT THERMAL ENERGY STORAGE USING ENERGY FROM ELECTRICITY GRID. [Final Year Project] (Unpublished)

Mohd Nasir, Mohd Alif Syazwan (2008) Experimental Modelling of the Fluid Flow in a Furnace Top of an Ethane Cracker in EPEMSB, Paka. [Final Year Project] (Unpublished)

Mohd Nasir, Muhammad Ahnaf (2016) Investigating the Effects of Addition of Different Copper Amount in Fe-Cu-C by Powder Metallurgy. [Final Year Project] (Submitted)

Mohd Nasir, Muhammad Nazif (2010) An Analytical Study of the Maintainability of Academic Building Air Conditioning System. [Final Year Project] (Unpublished)

Mohd Nazari@Anuar, Nor Naqiah (2011) Microstructural Characterization of FSW and FSSW Aluminum Alloy Plates. [Final Year Project] (Unpublished)

Mohd Nazmi bin Mohamad Saifull Bahri, Mohd Nazmi (2012) Thermal Shrinkage and Gas Voids Formation of Waxy Crude Oil. [Final Year Project] (Unpublished)

Mohd Nazree, Muhammad Azlan Nasrin (2016) Reducing Re-Absorption Losses In Luminescent Solar Concentrators ( LSC’s) By Using Nanomaterials. [Final Year Project] (Submitted)

Mohd Nazree, Muhammad Azlan Nasrin (2016) Reducing Re-Absorption Losses In Luminescent Solar Concentrators ( LSC’s) By Using Nanomaterials. [Final Year Project] (Submitted)

Mohd Nazri, Muhammad Syamil (2017) MODELLING AND SIMULATION OF PERFORMANCE MAP FOR VARIABLE GEOMETRY AXIAL COMPRESSOR. [Final Year Project]

Mohd Nazri Bin Me, Mohd Nazri (2008) Design of Laboratory Scale Prototype of Hydrothermal Crystallizer. [Final Year Project] (Unpublished)

Mohd Nazwan bin Dzulkarnine, Mohd Nazwan (2008) Phased Array: An Alternative of Non Destructive Test Method to Replace Conventional Radiographic Test (RT) and Ultrasonic Test (UT) for Linepipe Inspection. [Final Year Project] (Unpublished)

Mohd Nizom, Muhammad Syamim (2011) Study of Aerodynamic Forces on Double Decker Bus for Driving Stability. [Final Year Project] (Unpublished)

Mohd Noor, Mohammad Norazmeer (2020) Study on Material Integrity of Aluminium 7075 after Heat Treatment Process for Medical Tools. [Final Year Project] (Submitted)

Mohd Noor, Nor Fakhrul (2013) Carbon Nanotube Reinforced Aluminium Matrix Produced by Friction Stir Processing. [Final Year Project] (Unpublished)

Mohd Noor, Nursyazana (2013) Investigate the Dispersion and Suspension of Zinc and Silver Nano additives in Nano composites. [Final Year Project] (Unpublished)

Mohd Nor, Syah Hafiz (2014) Development of Prediction Model For System Performance. [Final Year Project] (Unpublished)

Mohd Nor Azami, Aina Syahira (2020) Numerical Analysis on Continuum Damage Mechanism of Thermoplastic Composite Pipe (TCP). [Final Year Project] (Submitted)

Mohd Nor Azlan b Sudin, Mohd Nor Azlan (2010) Study on Effect of Nanosilica Sand Addition on Physical and Mechanical Properties of High Density Polyethylene (HDPE). [Final Year Project] (Unpublished)

Mohd Noramin bin Md Isa, Mohd Noramin (2009) A Non-Contact Strain Measurement Method. [Final Year Project] (Unpublished)

Mohd Nordin, Mohammad Farhan (2010) Design of Active Suspension using Robust PID Controller. [Final Year Project] (Unpublished)

Mohd Norhafiz Bin Othman, Mohd Norhafiz (2010) Design and Development of Innovative Solar Water Heater. [Final Year Project] (Unpublished)

Mohd Norzahidi Bin Md Yusof, Mohd Norzahidi (2008) Design and Development of Clothes Drying Closet Using Solar Energy. [Final Year Project] (Unpublished)

Mohd Nuh Aizat B Mohd Daut, Mohd Nuh Aizat (2008) CNC Manufacturing of NACA 4412 Wing Sections for Wind Tunnel Test. [Final Year Project] (Unpublished)

Mohd Nurhadi bin Arifin, Mohd Nurhadi (2008) The Investigation into Tribological Properties of Carbon Fiber Reinforced Composite. [Final Year Project] (Unpublished)

Mohd Nuri Al-Amin, Nu’man Al-Basyir (2021) SIMULATION TO ENHANCE PERFORMANCE OF GLOBE VALVE. [Final Year Project] (Submitted)

Mohd Nurul Amin b Adnan, Mohd Nurul Amin (2009) Investigation of Stress Intensity Factor in a Single Edge Notched Bend Test Piece. [Final Year Project] (Unpublished)

Mohd Puad, Mohd Munir Effendy (2013) Effects of Ultraviolet and Rain on the performance of Fire Retardant Coating. [Final Year Project] (Unpublished)

Mohd Radzi Bin Mohd Anua, Mohd Radzi (2008) Design and Prototyping of Centrifugal Pump Impeller to be used as Water Injection Pump for Hydrocarbon Artificial Lift. [Final Year Project] (Unpublished)

Mohd Radzman, Mohamad Aizat (2015) Study of the Mechanical & Sound Absorption Properties of Natural Fibre (Corn Husks) as Reinforced Composite. [Final Year Project] (Unpublished)

Mohd Rafee, Nor Syazwani (2015) Simulation of Flow Characterization in Corrosion Test Rig of Thin Channel Flow Cell (TCFC). [Final Year Project] (Unpublished)

Mohd Rahman bin Mohd Rosli, Mohd Rahman (2010) The Tribological Study on Metallic Materials Which Had Undergone Surface Preparations Using Pin-on-Disc Testing Technique. [Final Year Project] (Unpublished)

Mohd Rashidi bin Samta, Mohd Rashidi (2009) Influence of NaCl deposition on Atmospheric Corrosion of Carbon Steel. [Final Year Project] (Unpublished)

Mohd Razali, Danial Syariman Razali (2011) Application of Crow-AMSAA to Predict Failure of Centrifugal Pumps with Increasing Failure Rates. [Final Year Project] (Unpublished)

Mohd Ridzuan, Muhammad Farhan Syauqi (2022) Effect of Turbulence Flow and Initial Particle Concentration on Jamming Probability through Coupled CFD-DEM Simulation. [Final Year Project] (Submitted)

Mohd Ridzuan bin Abdul Rahim, Mohd Ridzuan (2009) Study on the Current Performance of Piping and Structure Coatings in Oil and Gas Field. [Final Year Project] (Unpublished)

Mohd Rodzhan, Nur Syahirah (2016) Evaluation of Epoxy-Based Fire Retardant Basalt Fibre Reinforced Intumescent Coating with Aluminum Trihydrate (ATH) for Fire Retardancy Protection of Structural Steel. [Final Year Project]

Mohd Rosdi, Muhammad Muizzuddin (2022) Simulation For Embedding Conformal Heating Channel In Oil & Gas Angle Valve Using Additive Manufacturing Technology. [Final Year Project] (Submitted)

Mohd Rosdi, Mohd Akhimullah (2010) Contribution of Vehicle System and Accessories on Fuel Consumption of Perodua Viva. [Final Year Project] (Unpublished)

Mohd Ruzaini Bin Mohamad Noor, Mohd Ruzaini (2008) Optimizing Heat Insulation of a Solar Oven. [Final Year Project] (Unpublished)

Mohd Sabri, Fauzan Azmi (2011) DEVELOPMENT OF HONEYCOMB CORE FROM WASTE A4 PAPER AND INVESTIGATION ON ITS COMPRESSIVE PROPERTIES. [Final Year Project] (Unpublished)

Mohd Safwan Izzudin Bin Ramli, Mohd Safwan (2011) Line Modeling of CO2 Corrosion of Offshore Pipeline. [Final Year Project] (Unpublished)

Mohd Sagi, Khairuzzikri (2015) Product Families Development and Simulation of Well Completion System Products by Using Business Simulation Software. [Final Year Project] (Unpublished)

Mohd Saiful Bahren, Mohd Danial (2016) Small Car Carbon Dioxide Emission Analysis Through Drive Cycle Patterns on Chassis Dynamometer. [Final Year Project]

Mohd Saufi, Mohd Soffian Ariff B (2009) An Experimental Study on Strength of Friction Stir Welding. [Final Year Project] (Unpublished)

Mohd Shah Rizal Bin Mohd Yusof, Mohd Shah Rizal (2008) Engine Performance and Exhaust Emission Characteristics of Fuel Oil-Diesel Fuel Mixture in a Single Cylinder Engine. [Final Year Project] (Unpublished)

Mohd Shakif Bin Ahmad, Mohd Shakif (2009) Design of High Temperature Testing Attachments for Universal Testing Machine. [Final Year Project] (Unpublished)

Mohd Shukri, Farah Syazwani Bt (2009) Fundamental Study of Alcohol Sprays. [Final Year Project] (Unpublished)

Mohd Shukri Bin Mohd Nor, Mohd Shukri (2008) Material Compatibility And Fuel Properties For E10 And E85. [Final Year Project] (Unpublished)

Mohd Sobli, Mohd Akmal (2008) Spray Characteristic by using Phase Doppler Aiiemometry (PDA) and Laser Doppler Anemomctry (LDV). [Final Year Project] (Unpublished)

Mohd Suhaimi, Nur Aqilah (2012) CFD Simulation of the Natural Convection of Pinned Plate Solar Absorber. [Final Year Project] (Unpublished)

Mohd Syahmi Bin Jamludin, Mohd Syahmi (2010) Optimal Gait Analysis of Quadruped Robot. [Final Year Project] (Unpublished)

Mohd Syahmi Bin Mohd Yusof, Mohd Syahmi (2010) Modeling Intergranular Fracture at Elevated Temperature. [Final Year Project] (Unpublished)

Mohd Syuaib Bin Jamaludin, Mohd Syuaib (2012) Thermal Shrinkage and Gas Void Formation of Waxy Crude Oil with Additive. [Final Year Project] (Unpublished)

Mohd Tahir, Mohd Hazany (2004) INVESTIGATION AND COMBUSTION ANALYSIS OF ALTERNATIVE FUELS CHARACTERISTIC FOR INTERNAL COMBUSTION ENGINE. [Final Year Project] (Unpublished)

Mohd Tamam, Mohamad Qayyum (2014) Determination of Fluid Friction Factor for Nanofluids in Pipes. [Final Year Project] (Unpublished)

Mohd Taufek Bin Tumali, Mohd Taufek (2008) Design Of Freewheel Coupling. [Final Year Project] (Unpublished)

Mohd Thulus, Shahmirul Azri (2016) Green Fuel: Improvement of Engine Performance using Water-in-Diesel Emulsion (WiDE) with a Small Percentage of Hydrogen. [Final Year Project] (Submitted)

Mohd Ubaidillah bin Mohd Kamal, Mohd Ubaidillah (2008) Design of A Ballast Tank For A Small Underwater Remotely Operated Vehicle (ROV). [Final Year Project] (Unpublished)

Mohd Wafiuddin bin Abdul Rashid, Mohd Wafiuddin (2011) Finite Element Analysis of Residual Stresses in 316 Stainless Steel Pipelines SMAW Welding. [Final Year Project] (Unpublished)

Mohd Wafiuddin bin Abdul Rashid, Mohd Wafiuddin (2011) FINITE ELEMENT ANALYSIS OF RESIDUAL STRESSES IN 316 STAINLESS STEEL PIPELINES SMAW WELDING. [Final Year Project] (Unpublished)

Mohd Yasin, Irwan Syah (2008) Design andFabrication ofHybrid Solar-Biomass System for Crops Drying. [Final Year Project] (Unpublished)

Mohd Yasin, Mohd Nur Farhan (2011) Study ou Strength of Friction Stir Welded Plate in Corner Joint Configuration. [Final Year Project] (Unpublished)

Mohd Yasser Rabanie Bin Jamaluddin, Mohd Yasser Rabanie (2010) Design and Development of Steel Pipe Profiling Prototype. [Final Year Project] (Unpublished)

Mohd Yunus, Mohd Zulfadli (2008) Risk Based Inspection on Gas Processing Plant. [Final Year Project] (Unpublished)

Mohd Yusniman b Yusof, Mohd Yusniman (2010) EFFECT OF PROCESSING TECHNIQUES ON THE MECHANICAL PROPERTIES OF OIL PALM EMPTY FRUIT BUNCH COMPOSITE. [Final Year Project] (Unpublished)

Mohd Yusof, Yusnida (2005) Online control of process plant via fuzzy logic controller / by Yusnida Binti Mohd Yusof, TJ 223 .P55 Y94 2005. [Final Year Project]

Mohd Yusoff, Nik Zul Syafiq Affandi (2013) THE EFFECTIVE DURATION OF GAS NITRIDING PROCESS OF AISI 316L. [Final Year Project] (Unpublished)

Mohd Yusop, Hafifi (2008) MODELING AND ANALYSIS OF DISC BRAKE PERFORMANCE. [Final Year Project] (Unpublished)

Mohd Zafrin bin Zainal Azmi, Mohd Zafrin (2010) The Analysis of Calcium Ions Effect on CO2 Corrosion Using Electrochemical Impedance Spectroscopy. [Final Year Project] (Unpublished)

Mohd Zafrullah, Abdul Rahman (2011) Tribological Properties Analysis on Nitrided AISI 3161 Stainless Steel. [Final Year Project] (Unpublished)

Mohd Zahid, Muhammad Ilyas (2017) Contact and Bending Stress Analysis of Helical Gear Pair with Tip Relief. [Final Year Project] (Submitted)

Mohd Zain, Ihsan (2008) Fabrication of a Small Scale Model of Chancellor Award Trophy using CAD/CAM and CNC Milling Machine. [Final Year Project] (Unpublished)

Mohd Zain, Mohammad Farhan (2012) Design and Analysis of a Hyperbaric Chamber. [Final Year Project] (Unpublished)

Mohd Zaki Al Hafiz bin Rosli, Mohd Zaki Al Hafiz (2008) Implementation of dust control system using management and planning tools (MPT). [Final Year Project] (Unpublished)

Mohd Zamri, Ahmad Aiman Afif (2016) Mechanical Properties of Palas Fiber Reinforced Composite. [Final Year Project] (Submitted)

Mohd Zarir, Marni Zalikha (2020) Investigation on The Characteristics of Magnetorheological Elastomer Using Natural Rubber and Petroleum-Based Oil. [Final Year Project] (Submitted)

Mohd Zian, Muhammad Danial (2016) A Study of Acoustic Properties of Coconut Coir and Vermiculite Composite as Noise Insulation in Vehicles. [Final Year Project] (Submitted)

Mohd Zikri Bin Ahmad Abustaman, Mohd Zikri (2008) Processing of Alumina Powder into Ceramic Foam Materials by Impregnating Polyurethane Sponge with Bonded Ceramic Slurry. [Final Year Project] (Unpublished)

Mohd Zin, Muhammad Zaki (2013) STUDY OF JATROPHA CURCAS BIODIESEL BLEND WITH FOSSIL DIESEL THERMAL CHARACTERIZATION, ENGINE PERFORMANCE AND EMISSION COMPARE TO FOSSIL DIESEL. [Final Year Project] (Unpublished)

Mohd Zin, Nurul Aisyah (2011) Thermal Study of Gasifier Based Biomass Cookstove. [Final Year Project] (Unpublished)

Mohd ‘Arriffuddin bin ‘Allauddin, Mohd ‘Arriffuddin (2009) An experimental study on microstructure of Friction Stir Welded plates. [Final Year Project] (Unpublished)

Mohd. Ariff, Mohd. Hazwan (2013) Characterizations of Sprays of Modified Starch Solution at Elevated Temperature for Particle Coating Application. [Final Year Project] (Unpublished)

Mohd. Azlan B. Zamahari, Mohd. Azlan (2012) Design of a 3-DOF Parallel Mechanism with Shape Memory Alloy Actuators. [Final Year Project] (Unpublished)

Mohd. Kamalmursyid Bin Rozibah, Mohd. Kamalmursyid (2009) Sliding of Elastically Similar Complete Contacts. [Final Year Project] (Unpublished)

Mohd. Nasrul Bin Mat Yusof, Mohd. Nasrul (2008) Gas Turbine Blade Failure Due To Hot Corrosion. [Final Year Project] (Unpublished)

Mohd. Zhafri bin Mahdi, Mohd. Zhafri (2010) A Study Of Co-Firing Biomass With Coal As Potential Fuel. [Final Year Project] (Unpublished)

Mohd.Shaiful Baharuddin bin Halim, Mohd.Shaiful Baharuddin (2010) Calorific Values of PETRONAS Cokes Nitrated at Various Temperatures. [Final Year Project] (Unpublished)

Mohtar, Mohamad Najib (2008) Developing Carbon Particle Reinforced Alnmininm Composite byPowder Metallurgy. [Final Year Project] (Unpublished)

Mokhlis, Mohamad Mohaimin (2011) Design and Fabrication of Drive Train System for Bosch Power Tools Cordless Race 2011. [Final Year Project] (Unpublished)

Mokhlis, Mohamad Mohaimin (2011) Design and Fabrication of Drive Train System for Bosch Power Tools Cordless Race 2011. [Final Year Project] (Unpublished)

Mokhtar, Zainur Azwin (2008) ANALYSIS ON CHARACTERISTIC OF SABAH BENTONITE AT IDGH TEMPERATURE UNDER DYNAMIC CONDffiON. [Final Year Project] (Unpublished)

Moktar, Mohammad Faiz (2008) Study on Sintering Behavior of Alumina Particle Reinforced Aluminum Matrix Composites and Its Properties. [Final Year Project] (Unpublished)

Mos, Mohamad Anuar (2011) A Study on Wear Resistance of Copper- Silica Sand Nanoparticles Based Composites. [Final Year Project] (Unpublished)

Mostafa Saleh Zakzouk, Mostafa Saleh (2011) Study of Multi Staging Operation of Swirling Fluidized Bed. [Final Year Project] (Unpublished)

Mostar, Suraya Hani (2011) A Study of Wind Turbine Blade Shape Design. [Final Year Project] (Unpublished)

Mpho, Nesamari (2009) Simulation of Flow around a Bus with Active Drag Reduction Systelft. [Final Year Project] (Unpublished)

Muda, Mohd Shafizan Bin (2009) The Effects of High Temperature Gas Nitriding on Mechanical and Physical Properties of Austenitic Stainless Steel. [Final Year Project] (Unpublished)

Muhamad, Muhamad Fikri (2016) EFFECTS OF DRILLING GENERATED HEAT ON DELAMINATION IN GLASS FIBER REINFORCED EPOXY (GFRE) COMPOSITES. [Final Year Project]

Muhamad Afiq Bin Ahmad, Muhamad Afiq (2008) Gas Turbine Efficiency Improvement at Centralised Utility Facilities (CUF) Kertih, Terengganu. [Final Year Project] (Unpublished)

Muhamad Bakhtiar Bin Ismail, Muhamad Bakhtiar (2012) Model and Simulation of Heavy Load Carrier Mechanism. [Final Year Project] (Unpublished)

Muhamad Fadzir Bin Ab Razak, Muhamad Fadzir (2012) Numerical Investigation of Waste-Heat Driven Adsorption Desalination Cycle. [Final Year Project] (Unpublished)

Muhamad Faisal bin Ali, Muhamad Faisal bin Ali (2012) Development of Fuel Briquette from Palm Oil Mill Waste Mixed with Other Biomass Fuels. [Final Year Project] (Unpublished)

Muhamad Faris Bin Ali Osman, Muhamad Faris (2012) Mud Weight Prediction for Offshore Drilling. [Final Year Project] (Unpublished)

Muhamad Farizuddin Anwar bin Mansor, Muhamad Farizuddin (2008) Design Of A Cathodic Protection Against Corrosion For Marine And Offshore Structure. [Final Year Project] (Unpublished)

Muhamad Hafiz bin Bohari, Muhamad Hafiz (2010) The Influence of Varying Polymer Matrices on the Mechanical Properties of Biocomposites. [Final Year Project] (Unpublished)

Muhamad Isfan Imanullah b Adnan, Muhamad Isfan I (2012) Modeling of Subsea Control Module using Agito SimulationX. [Final Year Project] (Unpublished)

Muhamad Muhaidi bin Mazlan, Muhamad Muhaidi (2011) Wear investigation of elastically similar sliding bodies material. [Final Year Project] (Unpublished)

Muhamad Nasrah, Nur Syazni (2008) State Variable Feedbaek Control of a Gantry Crane. [Final Year Project] (Unpublished)

Muhamad Nor Bin Azizi, Muhamad Nor (2012) Design and Construction of smoke wire apparatus for wind tunnel flow visualization. [Final Year Project] (Unpublished)

Muhamad Yunos, Muhamad Aizat (2009) Mechanical Properties of Oil Palm Empty Fruit Bunch (EFB) - High Density Polyethene (HDPE): Influence OfProcessing Techniques. [Final Year Project] (Unpublished)

Muhamad Zainurul Asyraf bin Ismail, Muhamad Zainurul Asyraf (2008) CFD of Viscoelastic Fluid in Horizontal Flow Pipes. [Final Year Project] (Unpublished)

Muhamad Zulhairie bin Moideen, Muhamad Zulhairie (2008) Sway Reduction of Tower Crane. [Final Year Project] (Unpublished)

Muhammad, Norkhairi (2011) Development of Experimental Setup to Evaluate Drilling Fluid's Characteristic Using Tomography Method. [Final Year Project] (Unpublished)

Muhammad , Muhammad Fadhil (2011) Study on Characteristics of Syngas Derived From Various Biomasses. [Final Year Project] (Unpublished)

Muhammad Abduh Bin Mustapha, Muhammad Abduh (2012) Dynamics Fracture Propagation due to Cold Water Injection. [Final Year Project] (Unpublished)

Muhammad Afif bin Ilham, Muhammad Afif (2011) Design and Analysis of Run-of-River Water Turbine. [Final Year Project] (Unpublished)

Muhammad Afif bin Ilham, Muhammad Afif (2011) Design and Analysis of Run-of-River Water Turbine. [Final Year Project] (Unpublished)

Muhammad Afiq, Mansor (2011) Characterization of surface treated layers on Austenitic Stainless Steel and 9.3%Cr Ferritic steel resulting from High Temperature Nitriding. [Final Year Project] (Unpublished)

Muhammad Afiq bin Mansor, Muhammad Afiq (2011) Characterization of surface treated layers on Austenitic Stainless Steel and 9.3%Cr Ferritic steel resulting from High Temperature Nitriding. [Final Year Project] (Unpublished)

Muhammad Aizuddin Bin Muaz, Muhammad Aizuddin (2008) Implication of Design and Operation on Cooling Load and Energy Cost for Academic Building At UTP. [Final Year Project] (Unpublished)

Muhammad Aizuddin bin Zainalabidin, Muhammad Aizuddin (2008) Miscible CO2 Injection: Sensitivity To Fluid Properties Tinggi Field. [Final Year Project] (Unpublished)

Muhammad Amsyar bin Faizi, Muhammad Amsyar (2010) The Effect of Welding Different Plate Thickness on Heat Affected Zone Microstructure and Hardness. [Final Year Project] (Unpublished)

Muhammad Asyiq bin Ansorudin, Muhammad Asyiq (2010) A CFD Investigation Into The Thermal Comfort Of Building Envelope. [Final Year Project] (Unpublished)

Muhammad Atuf Hashim, Muhammad Atuf (2010) Investigation Of The Responses Of Passive Vehicle Suspension Models In Order To Obtain Better Understanding Of Their Performance Limits. [Final Year Project] (Unpublished)

Muhammad Azmeer Bin Rozman, Muhammad Azmeer (2012) Design of an Efficient Domestic Gas Oven. [Final Year Project] (Unpublished)

Muhammad Bin Hasanudin, Muhammad (2009) Simulation and Modeling of Front Suspension System of Proton Gen-2 Model Car. [Final Year Project] (Unpublished)

Muhammad Bin Roslan, Muhammad (2008) Thermal Characterization of Carbonaceous Pitches from Residue of PETRONAS Refinery. [Final Year Project] (Unpublished)

Muhammad Bukhari bin Abdul Jalil, Muhammad Bukhari (2008) Freezing Point Depression Method for Hydrate Monitoring. [Final Year Project] (Unpublished)

Muhammad Fadhil Bin Hassan Basri, Muhammad Fadhil (2012) Alternative Power Generation for Subsea Production System. [Final Year Project] (Unpublished)

Muhammad Fadhli bin Muhammad, Muhammad Fadhli (2011) Reliability Analysis of Heat Recovery Steam Generator Based on Creep. [Final Year Project] (Unpublished)

Muhammad Fahmi Bin Mustafa, Muhammad Fahmi (2008) A Study of Pressure Surge Effects on Transportation Pipeline. [Final Year Project] (Unpublished)

Muhammad Farid Bin Abdullah, Muhammad Farid (2008) Study and Design of Compressed Air System for Optimum Operation. [Final Year Project] (Unpublished)

Muhammad Farid bin Mohamed, Muhammad Farid (2010) Stress Concentration Factor at Two Adjacent Nozzles in a Cylindrical Pressure Vessel. [Final Year Project] (Unpublished)

Muhammad Faris Bin Che Salam, Muhammad Faris (2012) A Study on Repeatability of a Resin Infusion Strategy in the Manufacturing of Polymer Composite Wind Turbine Blade via Resin Infusion Process. [Final Year Project] (Unpublished)

Muhammad Faris Bin Mohd Pakri, Muhammad Faris (2011) STRESS ANALYSIS OF SUBSEA WELLHEAD HOUSING. [Final Year Project] (Unpublished)

Muhammad Hafiz Bin Abu Talib, Muhammad Hafiz (2011) Study on the Characterization of Silica Sand Nanoparticles-Iron Based Composites (Fe-SiO2) Using Nitrogen Atmosphere as Sintering Environment. [Final Year Project] (Unpublished)

Muhammad Hafiz Bin Rohimi, Muhammad Hafiz (2010) A Study of An Oscillating Water Column (OWC) to Harvest Wave Energy Using FLUENT Software. [Final Year Project] (Unpublished)

Muhammad Hafiz bin Zakaria, Muhammad Hafiz b Zakiah (2009) Jet Sintering of High Temperature Carbon Steel Powder Particles. [Final Year Project] (Unpublished)

Muhammad Hafizullah Bin Shamsudin, Muhammad Hafizullah (2009) Conceptual Design of an Underwater Manipulator for AUV. [Final Year Project] (Unpublished)

Muhammad Hariri Bin Wagiman, Muhammad Hariri (2010) Thermal Effect on a Plate While Welding Using Finite Element Method. [Final Year Project] (Unpublished)

Muhammad Hazwan Bin Desa, Muhammad Hazwan (2012) Design and Analysis of In-Field Liner (IFL) and IFL Pulling Head for Underwater Pipeline. [Final Year Project] (Unpublished)

Muhammad Hisyam Bin Noor Asmi, Muhammad Hisyam (2011) DRAG REDUCTION STUDY ON XANTHAN WATER SOLUTION AND XANTHAN OIL SOLUTION. [Final Year Project] (Unpublished)

Muhammad Husni bin Muhammad Sani, Muhammad Husni (2011) Combustion of a Controlled Condition Synthetic Gas with Diesel in a Single Cylinder Compression Ignition Engine. [Final Year Project] (Unpublished)

Muhammad Idris, Muhammad Fareez (2013) OIL-SAND PARTICLES (SOLID-LIQUID) PASSIVE SEPARATION IN PIPING SYSTEM. [Final Year Project] (Unpublished)

Muhammad Ikhbar B. Md Ismail, Muhammad Ikhbar (2008) Effect of Performance of A DC Motor by Replacing Ferrite Magnet with Melt Spun NdFeB Magnet. [Final Year Project] (Unpublished)

Muhammad Juffri, Muhammad (2021) CFD Investigation of Thermal Performance of the Flat Plate Solar Collector by using Vibration. [Final Year Project] (Submitted)

Muhammad Muizzuddin Bin Mazlan, Muhammad Muizzuddin (2010) Cryosurgery Tool For Cataract Removal. [Final Year Project] (Unpublished)

Muhammad Naim bin Ariffin, Muhammad Naim (2008) Design of a New Centrifugal Pump Impeller. [Final Year Project] (Unpublished)

Muhammad Nazree Bin Alehan, Muhammad Nazree (2011) Study on Improvement of Cooling Energy and Thermal Comfort of Klinik Pergigian Batu Gajah. [Final Year Project] (Unpublished)

Muhammad Razi bin Jusoh, Muhammad Razi (2010) Design and Analysis of a Compact In-Wheel Motor with New Disc Brake System for Retrofit Hybrid Electric Vehicle Application. [Final Year Project] (Unpublished)

Muhammad Redzuan bin Tauhid Ahmad, Muhammad Redzuan (2010) Computer Simulation of Biomass Gasification Process for Oil Palm Fronds in a Downdraft Gasifier. [Final Year Project] (Unpublished)

Muhammad Rubaie bin Mohammad Tahir, Muhammad Rubaie (2009) Development of Schlieren Visualization System for Study of Flame Characteristics. [Final Year Project] (Unpublished)

Muhammad Saifuldin Bin Bakri, Muhammad Saifuldin (2010) The Effect of Trim and Form Process on the Plated Leads of IC Packages. [Final Year Project] (Unpublished)

Muhammad Sani, Muhammad Husni (2011) Combustion of a Controlled Condition Synthetic Gas with Diesel in a Single Cylinder Compression Ignition Engine. [Final Year Project] (Unpublished)

Muhammad Shafiq bin Mat Shayuti, Muhammad Shafiq (2008) The Effect of High Temperature on Styrene Monomer Migration from Polystyrene Cup. [Final Year Project] (Unpublished)

Muhammad Shahmi bin Ahmad Shauki, Muhammad Shahmi (2010) Effect of Fluid Flow on Subsea Pipe Line Riser. [Final Year Project] (Unpublished)

Muhammad Shazwan Bin Che Ismail, Muhammad Shazwan (2010) Study into the Effect of Elevated Temperature on the Friction, Wear Behavior and Wear Mechanism of Typical KTMB Rail Track using Pin-on-Disc Testing Technique. [Final Year Project] (Unpublished)

Muhammad Syafeeq bin Ebining Amir, Muhammad Syafeeq (2010) Impact Resistance of Polyurea Coating. [Final Year Project] (Unpublished)

Muhammad Syahrul Goh, Muhammad Syafiq (2022) Thermophysical Behavior of the Hybrid Nanoparticles Reinforced Water-Based Drilling Fluid. [Final Year Project] (Submitted)

Muhammad Syamil B Zakaria, Muhammad (2011) Stress Analysis and Design of the Frame of a Personal Electric Vehicle. [Final Year Project] (Unpublished)

Muhammad Syamim bin Mohd Nizom, Muhammad Syamim (2011) Study of Aerodynamics of Double Decker Bus for Driving Stability. [Final Year Project] (Unpublished)

Muhammad Syukri bin Seam@Sa’im, Muhammad Syukri (2010) Study Into the Effect of Using Crude Palm Oil (CPO) as Cutting Fluid on the Tool Wear and Chip Formation During Milling Operations. [Final Year Project] (Unpublished)

Muhammad Taufiq bin Tajuddin, Muhammad Taufiq (2010) Stress Analysis on Water Injection Turbine Meter Blades. [Final Year Project] (Unpublished)

Muhammad Thaqif Bin Roslim, Muhammad Thaqif (2008) Experimental Study on Scale Control in Surface Pipelines by Magnetic Descaler. [Final Year Project] (Unpublished)

Muhammad Waseem, Muhammad Waseem (2012) Characterization Of Crude Oil Emulsion. [Final Year Project] (Unpublished)

Muhammad Wira Aiman b Kelana, Muhammad Wira Aiman (2010) An Analytical Study On Maintainability Of Academic Building Elevators. [Final Year Project] (Unpublished)

Muhammad Yusof B. Abd Rahim, Muhammad Yusof (2008) Pressure as an Indicator for Water Breakthrough for Horizontal Well Completion. [Final Year Project] (Unpublished)

Muhammad Zahhar bin Hamizer, Muhammad (2012) Stress Analysis in Elastically Similar Complete Contacts. [Final Year Project] (Unpublished)

Muhammad Zahid bin Md Bahari, Muhammad Zahid (2010) Study Of A Backup Ve_Tilatio_ System For Lecturers’ Office Space. [Final Year Project] (Unpublished)

Muhammad Zakwan bin Amran, Muhammad Zakwan (2010) Influence of Sodium Chloride (NaCl) Deposition on the Atmospheric Corrosion of Galvanized Steel Roofing. [Final Year Project] (Unpublished)

Muhammad Zamil bin Abdullah, Muhammad Zamil (2012) Thermal Analysis of Bovine Bone Drilling. [Final Year Project] (Unpublished)

Muhammad Zhafir Bin Abd Razak, Muhammad Zhafir (2010) Effects of Curvature on Impact Testing of Mild Steel SS400. [Final Year Project] (Unpublished)

Muhammad Zukni Bin Ibrahim, Muhammad Zukni (2008) Design and Analysis of Power Take-Off (PTO) and Telescopic Driveshafts. [Final Year Project] (Unpublished)

Muhammad kamil, Muhammad kamil (2011) SPRAY CHARACTERISTICS OF NONNEWTONIAN FLUIDS. [Final Year Project] (Unpublished)

Muhammad ‘Ammar bin Kassim, Muhammad ‘Ammar (2010) Residual Stress Measurements via X-ray Diffraction. [Final Year Project] (Unpublished)

Muhd Hafiz B Hilmi, Muhd Hafiz (2008) The Study of Linear Elastic Fracture Mechanics (LEFM) in Fracture. [Final Year Project] (Unpublished)

Muhd Khiyar, Nur Zeenaida (2008) An Investigation on the Tribological Performance of Carbon nanotube (CNT) as a Lubricant Additive to Locally Made Engine Oil. [Final Year Project] (Unpublished)

Muhd Syafiq bin Suhaimi, Muhd Syafiq (2010) Study On Improving The Conversion Efficiencies Of Photovoltaic Solar Panels Through The Use Of Water Film. [Final Year Project] (Unpublished)

Muhd Zulkifli Md Zain, Muhd Zulkifli (2010) Failure Analysis of a Heat Exchanger Tube. [Final Year Project] (Unpublished)

Muhd. Aizat Nazmi Bin Yusoff, Muhd. Aizat Nazmi (2009) The Influence of Temperature on Mechanical Properties and Fiber Damage. [Final Year Project] (Unpublished)

Muhibbullah Bin Haji Salleh, Muhibbullah (2012) Investigation of Welding Parameter on Resistance Spot Welding of Stainless Steel and Mild Steel Sheet. [Final Year Project] (Unpublished)

Muhil Prakaash A/L Manickam, Muhil Prakaash (2012) A NEW TYPE OF WIND TURBINE TO SUIT THE SOLAR CHIMNEY FOR POWER PRODUCTION. [Final Year Project] (Unpublished)

Mujtahid bin Mohd Abidin, Mujtahid (2008) An Investigation on the Effects of an Intake Air-Swirl Device on Fuel Consumption of a Spark Ignition Engine. [Final Year Project] (Unpublished)

Mukthar Rahman, Noorul Haskin (2009) Numerical Investigation of"On Roof Solar-Biomass Chimhey'. [Final Year Project] (Unpublished)

Mulubran, Freselam (2017) Life Cycle Costing Framework Integration Probabilistic and Fuzzy AHP. Doctoral thesis, Universiti Teknologi PETRONAS.

Muosteut, Muosteufa (2016) Life Cycle Cost Comparison of Heat Recovery Steam Generator and Auxiliary Boiler. [Final Year Project] (Submitted)

Musa, Abdelhafiz Mustafa (2013) Inhibition of Carbon Steel Corrosion in Pressurized CO2 Saturated Brine by an Imidazoline Derivative. Doctoral thesis, Universiti Teknologi PETRONAS.

Musa, Shahrul Ahmizan (2004) The effect of rice husk addictive on physical properties and applicability of Low Density Polyethylene. [Final Year Project] (Unpublished)

Mustafa, Ayad Tareq (2016) Performance Evaluation of A Developed Solar Vortex Engine. Doctoral thesis, Universiti Teknologi PETRONAS.

Mustafa, Afildhatul Nashima (2013) STUDY ON THE EFFECT OF VOIDS ON RESTART PUMPING OF GELLED CRUDE OIL IN PRODUCTION PIPELINE. [Final Year Project] (Unpublished)

Mustafa, Afildhatul Nashima (2013) STUDY ON THE EFFECT OF VOIDS ON RESTART PUMPING OF GELLED CRUDE OIL IN PRODUCTION PIPELINE. [Final Year Project] (Unpublished)

Mustaffa, Shahira Ernie Lyana (2011) TRANSMISSION SYSTEM IN SMALL WIND TURBINE. [Final Year Project] (Unpublished)

Muthusamy , Kabilan (2014) Water Leakage In Universiti Teknologi Petronas (UTP) From Taps to Carbon Dioxide (CO2) Emission. [Final Year Project] (Unpublished)

Muzir, Nur Ashila Nadhirah (2020) A Study of Electrochemical Measurements Under Microemulsion Condition Corrosion. [Final Year Project] (Submitted)

Myra Azwinna Binti Sapian, Myra Azwinna (2009) Improved Procedure to Prevent Hydrogen Induced Cracking for Welding Offshore Structures. [Final Year Project] (Unpublished)

N

N SETHAMBARAM, CARTHIKRAJA N SETHAMBARAM (2016) Numerical Simulation of Rock-Cutter Interaction in Drilling Operation Using ANSYS AUTODYN 3D. [Final Year Project] (Submitted)

N.Paramananthan, Nanthar Kugarn (2020) FUNCTIONALITY AND PERFORMANCE STUDY OF IOT INTEGRATED MULTI-TANK WATER LEVEL MONITORING SYSTEM. [Final Year Project] (Submitted)

NABILAH BT MASTUKI , NABILAH (2011) A STUDY OF ACETIC ACID ROLE IN CO2 CORROSION. [Final Year Project] (Unpublished)

NACHIAPPAN, ROHAN (2021) A COMPARATIVE STUDY OF INHIBITORS EFFICIENCY ON CORROSION OF CARBON STEEL REBAR IN CHLORIDE ENVIRONMENT. [Final Year Project] (Submitted)

NANDA KUMAR, KISHEN (2017) CARBOTHERMAL REDUCTION PROCESS OF MILLED AMORPHOUS SILICON DIOXIDE USING TAGUCHI’S METHOD. [Final Year Project] (Submitted)

NANIMINA, ALEXIS MOUANGUE (2015) POWDER-MIXED ELECTRICAL DISCHARGE MACHINING OF BIOMEDICAL AND INDUSTRIAL GRADE ALLOYS. PhD. thesis, Universiti Teknologi PETRONAS.

NASEER, HARIS (2021) PERFORMANCE ANALYSIS OF COMPOUND PARABOLIC CONCENTRATOR INTEGRATED WITH EVACUATED TUBE RECEIVER USING HYBRID NANOFLUIDS. Masters thesis, Universiti Teknologi PETRONAS.

NASIR RESHID, MESERET (2013) AVAILABILITY MODEL FOR A COGENERATION SYSTEM SUBJECTED TO REDUNDANCY. PhD. thesis, Universiti Teknologi PETRONAS.

NAZER MOHAMED, MOHAMED HAZSRIM (2017) THERMODYNAMIC MODELLING OF ORGANIC RANKINE CYCLE (ORC) FOR WASTE HEAT RECOVERY OF A GAS TURBINE ENGINES. [Final Year Project]

NESARAJ, JESHURUN (2017) INVESTIGATION OF THE THERMAL PERFORMANCE OF A SOLAR ASSISTED AIR CONDITIONER UNDER TROPICAL CLIMATE. [Final Year Project]

NEW, MEI YET (2012) NUMERICAL STUDY OF CROSS FLOW FAN PERFORMANCE IN AN INDOOR AIR CONDITIONING UNIT. Masters thesis, Universiti Teknologi PETRONAS.

NG, EUNICE HUI RONG (2020) The influence of acid surface treatment on the physical and mechanical properties of steel structure as a precursor for fiber metal laminate structure. [Final Year Project] (Submitted)

NGAH, MUHAMMAD HELMI (2012) Tensile and Flexural Properties of Grass/Epoxy Composites. [Final Year Project] (Unpublished)

NGUYEN, HUU PHUOC NGUYEN (2007) Design of a glass climbing robot. [Final Year Project] (Unpublished)

NIK MAHAMED, NIK SAHIRA NAJIHA (2016) Development of Solid Fuel Briquette from Coal Waste. [Final Year Project] (Submitted)

NIK MOHAMED AFFANDI, NIK FAIZARIF (2004) DESIGN OF BRAKE TEST JIG TO REPRESENT ACTUAL BRAKING CONDITIONS. [Final Year Project] (Unpublished)

NIK YUSOFF, NIK HASSANUDDIN (2020) CHARACTERIZATION OF NI-CO/ALUMINA COATING PRODUCED FROM THE ALKALINE BATH AS A FUNCTION OF DEPOSITION PARAMETERS, ELECTROLYTE MOLARITY AND ALUMINA CONTENT. PhD. thesis, Universiti Teknologi PETRONAS.

NISSAR, ZUHAIB (2020) MODELLING AND EXPERIMENTAL INVESTIGATION OF MICROEXPLOSIONS IN FUEL DROPLETS. Masters thesis, Universiti Teknologi PETRONAS.

NIZAM AKBAR, AMAR NAZMI ZULKARNAIN (2017) COMPARATIVE ANALYSIS OF OPTICAL FLOW MEASUREMENT TECHNIQUE. [Final Year Project] (Submitted)

NOOR AZAHAN, AHMAD FAIZ SAFWAN (2017) DYNAMIC STABILITY OF AEROSTAT DRONE. [Final Year Project] (Submitted)

NORAIMAN, WAN MUHAMMAD (2017) ANALYSIS OF OPTIMAL MANUFACTURING METHOD FOR DISCRETE PARTS WITH THIN SECTIONS. [Final Year Project]

NORAN, NORAZ AL-KHAIRI (2013) HOMOGENEOUS CHARGE COMPRESSION IGNITION IN A COMPRESSED NATURAL GAS ENGINE WITH A GASOLINE PILOT. Masters thesis, UTP.

NORDIN, ADZUIEEN (2017) EXERGOECONOMIC MODEL ON POWER AND CHILLED WATER COST RATES FOR GAS-FUELED DISTRICT COOLING SYSTEM. PhD. thesis, Universiti Teknologi PETRONAS.

NORDIN, AFIF AIMAN (2016) Comparative Study on Red Mud Modified Intumescent Coating. [Final Year Project] (Submitted)

NUR AZURA BINTI KAMARUZZAMAN, NUR AZURA (2008) Wave Energy Eletric Generator. [Final Year Project] (Unpublished)

NUR SYAFIQAH BINTI MD RAZIB, NUR SYAFIQAH (2011) STUDY OF WEATHER RESISTANCE OF INORGANIC FILLERS BASED INTUMESCENT COATING. [Final Year Project] (Unpublished)

Nabila Farhana binti Abdul Khalil, Nabila Farhana (2011) Mechanical Properties of Low-Density Polyethylene/Recycled Poly(ethylene Terephthalate) (LDPE/r-PET) Microfibrillar Composite. [Final Year Project] (Unpublished)

Nabilah Binti Amir Hamzah, Nabilah (2010) Study of Plain Dent on Seamless Mild Steel Pipe. [Final Year Project] (Unpublished)

Nadiah Mohd Zaki, Nadiah (2008) CFD Simulation of Visco-Elastic Fluids in Vertical Flow Pipes. [Final Year Project] (Unpublished)

Nadiatul Haswin bte. Hassan Merican, Nadiatul Haswin (2011) CHARACTERIZATION OF 316L STAINLESS STEEL POWDER INJECTION MOLDING. [Final Year Project] (Unpublished)

Nadrah bt Isa, Nadrah (2012) X-Ray Amorphous Pattern Characterization of PETRONAS Petroleum Coke Product as a Potential for Advanced Carbon-Carbon Composite Material Precursors. [Final Year Project] (Unpublished)

Najibah bt. Tajul Zahari, Najibah (2010) Effects of Rockwool and Glasswool on Thermal Performance of Intumescent Coating. [Final Year Project] (Unpublished)

Najwa Sofwani Mohamad Shiham., Najwa Sofwani (2012) ANALYSIS ON PROCESS PARAMETERS OF SLS RAPID PROTOTYPING PROCESS. [Final Year Project] (Unpublished)

Naseer, Abqaat (2019) Grafting Of Metal Oxides On Graphene Nanoplatelets For Copper Composites Via Powder Injection Molding. Masters thesis, Universiti Teknologi PETRONAS.

Nashreen Mhd Razali, Nashreen (2008) Development of an Analytical Model of Gas Turbine to Predict the Gas Turbine Degradation. [Final Year Project] (Unpublished)

Nasindram, N.Diviniya (2015) The Effect of Time during Post Weld Heat Treatment (PWHT) on Mechanical Properties of Copper Alloy with Gas Metal Arc Welding (GMAW). [Final Year Project] (Unpublished)

Nasir Gathoth Subroto, Affan (2015) THE ANALYSIS OF PDC CUTTER CHARACTERISTIC IN HARD FORMATION DRILLING RELATING TO WEAR (BACK & SIDE RAKE ANGLE). [Final Year Project] (Unpublished)

Nasrudin, Muhammad Arif (2017) FABRICATION OF COMPOSITE BALL SOCKET PIPELINE JACKET FOR SUBSEA FLOWLINES PROTECTION SYSTEMS. [Final Year Project]

Nawal Binti Shamsuddin, Nawal (2011) Study of Carbon Dioxide Corrosion on Carbon Steel at Different Salt Concentrations. [Final Year Project] (Unpublished)

Nawi, Rohaida Idayu (2005) Design And Construction Of Vertical Turbine For Wind Power Farming/ by Rohaida Idayu Nawi, TJ 900 .R737 2005. [Final Year Project]

Nazarudin, Muhammad Amir Adli (2015) Run River Pico-Hydro System from Water Treatment Effluent Discharge. [Final Year Project] (Unpublished)

Nazri Talib, Nazri (2010) Development of Spreadsheet MRP model for Panel Front Door Left Hand Side Assembly. [Final Year Project] (Unpublished)

Nelson, Kevin (2013) Entrance Length of Polymer Flows. [Final Year Project] (Unpublished)

Nesamari Mpho, Nesamari (2009) Simulation of Flow around a Bus with Active Drag Reduction System. [Final Year Project] (Unpublished)

Ng, Chan Wai (2008) Study the Effects of Fluids Dominating Forces on Pseudo Relative Permeability Curve. [Final Year Project] (Unpublished)

Ng, Choon Hing (2008) The Effect of Increased Fuel Intake Temperature on the Performance of Internal Combustion Engines. [Final Year Project] (Unpublished)

Ng, Min Kiat (2009) Effects of Wake Turbulence on Aircraft Wing Model Experimental Method. [Final Year Project] (Unpublished)

Ng , Ming Kiat (2009) Effects of the Wake Turbulence on Aircraft Wing Model: Experimental Method. [Final Year Project] (Unpublished)

Ngaing , Ing Kai (2016) Experimental Investigation of Engine Performance and Exhaust Emissions of DI Diesel Engine using various Water in Diesel Emulsion. [Final Year Project] (Submitted)

Ngatini, Maini Rizal (2008) Effects of Fiber Reinforcement in Intumescent Formulations for Char Strengthening. [Final Year Project] (Unpublished)

Ngo Dinh Phuong, Dinh Phuong (2008) Simulation and Performance Test of CNC Machining Center. [Final Year Project] (Unpublished)

Nguan, Heng Kok (2017) Heat Transfer Enhancement on Geothermal Energy Extraction from Unused Oil Well. [Final Year Project]

Nik Afifi Bin Nik Abd Rahim, Nik Afifi (2010) Stress Analysis of Steam Methane Reformer Tubes. [Final Year Project] (Unpublished)

Nik Ahmad Ridzlan, Nik Aiemen Razieq (2016) Pipeline modelling for leak detection using pressure gradient method. [Final Year Project] (Submitted)

Nik Leh, Nik Siti Hasniati (2011) A Study on Energy Efficiency ofUTP Academic Buildings. [Final Year Project] (Unpublished)

Nik Mohamed Daud, Nik Mohd Radi (2011) Design of a Mini Thermal Storage System for Air- Conditioning Service. [Final Year Project] (Unpublished)

Nik Mohd Faizal Bin Nik Abd Ghani, Nik Mohd Faizal (2009) Design, Rapid Prototyping, and Testing of the Darrieus Wind Turbine. [Final Year Project] (Unpublished)

Nik Mohd Radi Bin Nik Mohamed Daud, Nik Mohd Radi (2011) Design of a Mini Thermal Storage System for Air-Conditioning Service. [Final Year Project] (Unpublished)

Nizam Shah, Muhammad A’izuddin (2016) Investigation on Grain Size Changes in Gamma Prime Precipitate on Varying Surface Location of IN738 Engine Turbine Blade. [Final Year Project] (Submitted)

Nizamuddin, Mohamed Fazlan (2016) Subsea Pipelines Health Prognostics Using Rate of Crack Propagation and Marco-Starkey, Cumulative Damage Theory. [Final Year Project] (Submitted)

Noor Atilia binti Selamat, Noor Atilia (2010) Development of Biocomposite: The Influence of Natural Fillers. [Final Year Project] (Unpublished)

Noor Azman, Muhammad Noor Fadhli B. (2009) Development of a Laser Attenuation Measurement System for Quantification of Suspended Particles. [Final Year Project] (Unpublished)

Noor Azmi, Nur Amilia (2015) A Study of Preferential Weld Corrosion in the Presence of Carbon Dioxide and Acetic Acid. [Final Year Project] (Unpublished)

Noor Farhane Binti Che Harun, Noor Farhane (2012) Study of Harnessing Raindrop Energy Potential in Perak, Malaysia. [Final Year Project] (Unpublished)

Noor Hidayu Bt Alishopian, Noor Hidayu (2010) Mathematical Modelling, Computation & Analysis of Oil Tanker Stability. [Final Year Project] (Unpublished)

Noor Ilyia Binti Mohd Yusnee, Noor Ilyia (2010) Life Cycle Assessment of Gas District Cooling Plant Absorption Chiller at Universiti Teknologi Petronas. [Final Year Project] (Unpublished)

Noor Nadia Azzahraa binti Afandi, Noor Nadia Azzahraa (2009) Effect of Rotational and Transverse Speeds on Friction Stir Welded Plates. [Final Year Project] (Unpublished)

Noor Shahilia Binti Ishak, Noor Shahilia (2010) Study of the Physical and Mechanical Properties of Sintered Nitrided Austenitic Stainless Steel Powder. [Final Year Project] (Unpublished)

Noor Syaffynas bt Yusoff, Noor Syaffynas (2010) Centrifugal Pump Characteristics for Crude Oil Transfer. [Final Year Project] (Unpublished)

Nooratikah binti Saari @ Awang, Nooratikah (2010) Estimation of the probability of failure for Corrosion Under Insulation using Logistic Regression Model. [Final Year Project] (Unpublished)

Nor Asma Rusni Ab. Alim, Nor Asma Rusni (2008) A Study on the Effect of Surface Finish on Corrosion of Carbon Steel in CO2 Environment. [Final Year Project] (Unpublished)

Nor Azeanty binti Mohd Adzan, Nor Azeanty (2010) Pump as Turbine for Micro Hydro Power. [Final Year Project] (Unpublished)

Nor Azlan, Adam (2016) Failure Analysis of Broken Pump Shaft. [Final Year Project] (Submitted)

Nor Azlinda Azmi, Nor Azlinda (2012) Buckling Analysis of Single-walled Carbon Nanotubes (SWCNTs) using Finite Element Method. [Final Year Project] (Unpublished)

Nor A’tiqah Bt Mohd Nurulhuda, Nor A’tiqah (2010) Harmonic Response of the Offshore Crane Boom Structure. [Final Year Project] (Unpublished)

Nor Shaharim, Mohammad Haqimi Izwan (2020) Parametric Study of Double Axes Tracking Heliostat to Optimize Heliostat Field Efficiency. [Final Year Project] (Submitted)

Nor Zaihar, Naim Zafran (2021) Non-Linear Structural Analysis of a Tensioner During Pipe Lay. [Final Year Project] (Submitted)

Norafif Afnan Mohd Nordin, Norafif Afnan (2008) Effect of Deformation to the Performance of Aluminium Sacrificial Anode. [Final Year Project] (Unpublished)

Norafizal, Arif Isyraf (2020) Effects of Vacuum Bagging Techniques on Mechanical Properties of CarbonEpoxy Laminates. [Final Year Project] (Submitted)

Norahmad Shah, Amira Nabilla (2013) Development of Maintainability Analysis Toolkit (MAT) for Analysing Plant Maintenance Data of Gas Processing Plant at Operational Phase. [Final Year Project] (Unpublished)

Noraini Binti Alias, Noraini (2010) Effect of Sintering Time on Properties of Carbon Nanotubes Reinforced Aluminum Composite. [Final Year Project] (Unpublished)

Noraini Binti Esa, Noraini (2009) Comparison of Microstructure and Hardness of Sintered Carbon Fiber and Carbon Nanotubes Reinforced Copper Matrix. [Final Year Project] (Unpublished)

Norashid, Muhammad Syukri (2013) MICROSTRUCTURE AND MATERIAL FLOW INVESTIGATION OF DISSIMILAR FRICTION STIR WELDED PLATES. [Final Year Project] (Unpublished)

Nordi, Nor Helmi (2013) Tensile Strength of Polyoxymethylene/Carbon Fiber/Glass Fiber Hybrid Composite. [Final Year Project] (Unpublished)

Nordin, Muhammad Nur Azib (2022) Heat Transfer Enhancement of Thermoelectric Generator with Corrugated Surface Structure Using MWCNT Nanofluid. [Final Year Project] (Submitted)

Nordin, Normayati (2016) Performance Investigation of Turning Diffusers at Various Geometrical and Operating Parameters. Doctoral thesis, Universiti Teknologi PETRONAS.

Nordin, Abd Halim (2011) Design of A Heat Exchanger for Gas Turbine Inlet Air Cooling System. [Final Year Project] (Unpublished)

Nordin, Amzani Nazmi (2016) Performance Monitoring Analysis of Centrifugal Compressor Using Statistical Process Control. [Final Year Project]

Nordin, Nazarul (2013) SOLAR WATER HEATER SYSTEMS FOR COMMERCIAL BUILDINGS. [Final Year Project] (Unpublished)

Norhafiza Binti Mohd Zukepeli, Norhafiza (2010) Stress Analysis Of Aboveground Atmospheric Storage Tank Due To Edge Settlement. [Final Year Project] (Unpublished)

Norhana Mohd Aripin, Norhana (2010) Study On The Flow Characteristic On A Bluff Body Around Circular Cylinder. [Final Year Project] (Unpublished)

Norlina binti Mohd Sarkawi, Norlina (2009) Design of Ice Thermal Energy Storage System for GDC (UTP) Plant. [Final Year Project] (Unpublished)

Norsaiful Bin Rosli, Norsaiful (2010) Effects of Drilling Fluid Rheological Properties on Drill Cuttings Transport. [Final Year Project] (Unpublished)

Norsham, Nurufirin (2011) A Study of Indoor Air Quality In UTP's Academic Buildings No.18 Level 3. [Final Year Project] (Unpublished)

Ntutumu Nsang, Dionisio Miguel (2016) Study on Reduction of Cooling Energy for Air Conditioning by Flexible Space Compartmentalization in Residential Houses. [Final Year Project] (Submitted)

Nur Aimi Binti Abdul Rahim, Nur Aimi (2010) Attitude Maneuver of a Flexible Satellite by Using Thrusters based on PD Controller. [Final Year Project] (Unpublished)

Nur Ain Binti Sulaiman, Nur Ain (2010) Transient Simulation of Energy in a Terraced House Using TRNSYS. [Final Year Project] (Unpublished)

Nur Azirah Binti Mat Radzi, Nur Azirah (2009) Exploratory Studies on Largely Available On The Shelf Materials for Smart Actuators. [Final Year Project] (Unpublished)

Nur Farah ‘Izzati Bt Zakaria, Nur Farah ‘Izzati (2010) Effects of Ceramic Fibre on Char Strength of Intumescent Coating. [Final Year Project] (Unpublished)

Nur Fauzianie Roslan, Nur Fauzianie (2010) Influence Of Heat Treatment Temperature On Mechanical Properties Of Heat Affected Zone (Haz). [Final Year Project] (Unpublished)

Nur Hafiz Bin Ahmad Zubir, Nur Hafiz (2009) Sand Control Selection for Wells in Tukau Field. [Final Year Project] (Unpublished)

Nur Hasyimah Bt Mohamad Afandi, Nur Hasyimah (2008) Study Of Zeolite In Mitigating Formation Damage Due To Inorganic Scaling. [Final Year Project] (Unpublished)

Nur Hazwana binti Kabol, Nur Hazwana (2010) Three Dimensional Analysis on Stress Concentration in a Gas Turbine Blade. [Final Year Project] (Unpublished)

Nur Hazwany Bt Mohd Hatta, Nur Hazwany (2009) Effects of Wake Turbulence on Aircraft Wing Section Numerical Study. [Final Year Project] (Unpublished)

Nur Liyana Farizah Binti Zahri, Nur Liyana Farizah (2009) A CFD Investigation into the Transient Aerodynamic Forces on Overtaking Road Vehicles Models. [Final Year Project] (Unpublished)

Nur Sabrina binti Md Danial, Nur Sabrina (2012) Study on Physical and Mechanical Properties of Rubber Latex Composites with SiO2 Addition. [Final Year Project] (Unpublished)

Nur Sahira binti Dusuki, Nur Sahira (2010) Design of Two Stage Charging System for Thermal Energy Storage (TES) Tank for GDC UTP. [Final Year Project] (Unpublished)

Nur Syahadah binti Jamaludin, Nur Syahadah (2008) Fabrication of Pinion Gear for PowerWindow of a Car through Powder Metallurgy Technique. [Final Year Project] (Unpublished)

Nur Syazni binti Muhamad Nasrah, Nur Syazni (2008) State Variable Feedback Control Of A Gantry Crane. [Final Year Project] (Unpublished)

Nur Zahirah Binti Zakaria, Nur Zahirah (2008) Predesign of Latent Heat Thermal Energy Storage for UTP GDC System. [Final Year Project] (Unpublished)

Nur Zaihasra Zahari, Nur Zaihasra Zahari (2012) TEMPERATURE DISTRIBUTION FOR PALM OIL MILL USING IR THERMAL IMAGING. [Final Year Project] (Unpublished)

Nur Zeenaida Muhammad Khiyar, Nur Zeenaida (2008) An Investigation on the Tribological Performance of Carbon nanotube(CNT) as a Lubricant Additive to Locally Made Engine Oil. [Final Year Project] (Unpublished)

Nur ‘Atikah bt Jamaludin Alias, Nur ‘Atikah (2012) Failure Analysis on Heat Exchanger Tube Bundle Leakage. [Final Year Project] (Unpublished)

Nurfariza Binti Mohd Zuki, Nurfariza (2008) Reducing Sway of Gantry Crane Load. [Final Year Project] (Unpublished)

Nurhadiyanto, Mohanimad Arif (2005) Drive Signal Simulation through Vehicle Suspension Modeling. Masters thesis, Universiti Teknologi PETRONAS.

Nurhafeezan Bin Malik, Nurhafeezan (2010) Study on the Effect of NanoSilica Sand Addition to the Physical and Mechanical Properties of Iron Powder. [Final Year Project] (Unpublished)

Nurhafizah Binti Abdullah, Nurhafizah (2009) Design and Fabrication of Portable Smoke Tunnel for Flow Visualization. [Final Year Project] (Unpublished)

Nurhusna Bt Yusoff , Nurhusna (2008) Design Calculations and Experimental Analysis of “Over Roof Solar Chimney”. [Final Year Project] (Unpublished)

Nursyazwani binti Ramli, Nursyazwani (2011) Process Reliability Analysis of Gas District Cooling by Using Production Chilled Water Data. [Final Year Project] (Unpublished)

Nurul Aini Binti Mohd Faudzi, Nurul Aini (2009) Microstructure Characterization of As-cast, Creep-tested and Ex-service Steam-methane Reformer Tube. [Final Year Project] (Unpublished)

Nurul Aisyah Binti Mohd Zin, Nurul (2011) Thermal Study of Gasifier Based Biomass Cookstove. [Final Year Project] (Unpublished)

Nurul Akma Binti Brahim, Nurul Akma (2009) Predicting Failures for Repairable System Subjected to Imperfect Maintenance. [Final Year Project] (Unpublished)

Nurul Alia binti Mohd Anuar, Nurul Alia (2012) Stress Analysis of Underwater Pipeline for Irregular Seabed Topography Using CAESAR II. [Final Year Project] (Unpublished)

Nurul Alia binti Mohd Anuar, Nurul Alia (2011) Stress Analysis of Underwater Pipeline for Irregular Seabed Topography Using CAESAR II. [Final Year Project] (Unpublished)

Nurul Atiqah Binti Roszopor, Nurul Atiqah (2011) Assessment for Process Capability Using Weibull Analysis. [Final Year Project] (Unpublished)

Nurul Fatin Syazwani Binti Azman, Nurul Fatin Syazwani (2012) Finite Element Analysis of Contra Bass Bridge. [Final Year Project] (Unpublished)

Nurul Hazirah Binti Abd Aziz, Nurul Hazirah (2009) Design Optimization of a 3-phase(oil,water,gas) Separator. [Final Year Project] (Unpublished)

Nurul Hazwani Ahmad Shokri, Nurul Hazwani (2012) Study of Fluid-Structure Interaction (FSI) On Benfield Solution (BS) Line Using ANSYS. [Final Year Project] (Unpublished)

Nurul Hidayah Binti Mohammad Radzi, Nurul Hidayah (2009) Metal-to-Metal Sealing for High Pressure Subsea Production System(SPS) Bolted Flange Connector. [Final Year Project] (Unpublished)

Nurul Najat binti Ahmad, Nurul Najat (2011) Study of the Microstructure of the Gas Turbine Internal Blade. [Final Year Project] (Unpublished)

Nurul Rawaida Ain Burhani, Nurul Rawaida Ain (2010) Effect of Compaction Pressure on Final Properties of Multiwall Carbon Nanotubes (MWCNTs) reinforced Aluminum (Al) Composite. [Final Year Project] (Unpublished)

Nurul Syafiqa Binti Misran, Nurul Syafiqa (2010) Fabrication of Micro Unmanned Aerial Vehicle Using Rapid Prototyping and Rapid Tooling. [Final Year Project] (Unpublished)

Nurul Syahirah Binti Abdul Hamid, Nurul Syahirah (2010) Study On Harnessing Solar Energy For Power Supply From Chancellor Complex Roof. [Final Year Project] (Unpublished)

Nurul Zahirah binti Zainudin, Nurul Zahirah (2009) Study on The Material Factor in Erosion-Corrosion. [Final Year Project] (Unpublished)

Nurulzahar, Farhan Adib (2021) Study of Organic Acid Corrosion for Steel Pipeline in Wet. [Final Year Project] (Submitted)

Nurzaki Bin Ikhsan, Nurzaki (2008) Design and Analysis of a Hybrid Composite-Steel Frame Chassis for a Small Racecar. [Final Year Project] (Unpublished)

Nurzaki Bin Ikhsan, Nurzaki (2008) Design and Analysis of a Hybrid Composite-Steel Frame Chassis for a Small Racecar. [Final Year Project] (Unpublished)

Nurzarith Izzat Bt Othman, Nurzarith Izzat (2010) Analysis of the Hydro Thermal Behaviour of Waxy Crude during Pipeline Restart. [Final Year Project] (Unpublished)

Nur’Aisyah bt Marzuki, Nur’Aisyah (2012) DEVELOPMENT AN AGGREGATE PLANNING MODEL FOR DISCRETE COMPONENT MANUFACTURING: A CASE STUDY FOR DISC BRAKE. [Final Year Project] (Unpublished)

Nuzul Hazwani Bt Mohamad Hanafi, Nuzul Hazwani (2010) Study the Effect of Temperature on Crack Propagation in Ceramics. [Final Year Project] (Unpublished)

O

OMAR, MOHD ADAM (2009) Thermal Stress Distribution In Brake Disc For Small Vehicle. [Final Year Project] (Unpublished)

ONG, SZE KUAN (2021) STACKING SEQUENCE OPTIMIZATION OF LAMINATE COMPOSITES USING HASHIN FAILURE CRITERIA. [Final Year Project] (Submitted)

OO, AUNG MYINT (2011) Knowledge Based Management For Rotating Equipment Diagnostics. [Final Year Project] (Unpublished)

OTHMAN, MOHD HAFIZ (2010) MICROSTRUCTURE AND MECHANICAL PROPERTIES EVALUATIONS OF HEAT TREATED DISSIMILAR METAL JOINT WELDMENT BETWEEN API 5CT C90 AND ASTM A182 F22. [Final Year Project] (Unpublished)

OTHMAN, NURUL HUSNA (2021) EPOXY COATING REINFORCED WITH GO-ZNO AS COATINGS FOR THE PROTECTION AGAINST HIGH-PRESSURE CO2 GAS ENVIRONMENT. PhD. thesis, Universiti Teknologi PETRONAS.

OUMER, AHMED NURYE (2012) MODELING OF FIBER SUSPENSIONS FOR PREDICTION OF FIBER ORIENTATION IN INJECTION MOLDED POLYMER COMPOSITES. PhD. thesis, Universiti Teknologi PETRONAS.

Ogail Abdelsalam Elhassan, Ali (2017) Performance validation of a Remotely Monitored Off-Grid PV Plant in UTP. [Final Year Project]

Omar, Hasliza (2010) A Study on Highway Guardrail Improvement. [Final Year Project] (Unpublished)

Omar, Muhammad Ikmal (2018) Corrosion of Copper-coupled Steel in Open Recirculating Cooling Water System. [Final Year Project] (Submitted)

Omar, Nor Sharifah (2011) The Effects of Fiberglass on the Thermal Insulation Properties of Intumescent Coatings. [Final Year Project] (Unpublished)

Omar, Noraimi (2018) Antifriction Bearing Malfunction Detection and Diagnostics using Hybrid Approach. [Final Year Project] (Submitted)

Omar , Siti Aisyah (2008) Cooperative Control of Dual Series Robots. [Final Year Project] (Unpublished)

Omar Bayagoob, Ashraf Yaaqob (2015) Nano Electrochemical Polishing of Titanium Alloy using Ionic Liquid. [Final Year Project] (Unpublished)

Ong, Chin K wang (2008) Optimization Of Well Location And Number Of Production Well. [Final Year Project] (Unpublished)

Ong , Chuan Faith (2015) Parametric Study on Steam Generation of Heat Recovery Steam Generator at 2 × 4.2MW District Cooling Plant. [Final Year Project] (Unpublished)

Ong Mar Vin, Ong Mar (2011) THERMAL SHRINKAGE AND GAS VOID FORMATION OF WAXY CRUDE OIL -FLOW LOOP DEVELOPMENT. [Final Year Project] (Unpublished)

Osman, Muhammad Fikri (2014) Performance Assessment Of Sacrificial Anode Cathodic Protection Of Subsea Pipeline. [Final Year Project] (Unpublished)

Osman, Muhammad Hafizuddin (2015) INVESTIGATION OF REMAINING USEFUL LIFE OF GAS TURBINE BLADE. [Final Year Project] (Unpublished)

Osmira, Nur Husna Anira (2016) Development of Markov Model for Piping System Reliability Analysis Subjected to Corrosion Under Insulation. [Final Year Project]

Othman, Ahmad Faizal (2014) Orientation Effect On Mechanical Properties of Kenaf Reinforced Polypropylene Composite. [Final Year Project] (Unpublished)

Othman, Mohamed Azeem (2016) Studies of structural properties of char from intumescent coating. [Final Year Project] (Submitted)

Owolabi, Afolabi Lukmon (2016) Performance Enhancement of Nano-additives in a Flat-plate Solar Collector Integrated with Thermal Energy Storage Systems. Doctoral thesis, Universiti Teknologi PETRONAS.

P

P Dhinesh Kumar A/L Panneerchelvam, Dhinesh Kumar (2009) Study on Telescopic Walkway Design of Jetty Gangway. [Final Year Project] (Unpublished)

P.Arumugam, Yogenraj (2021) Investigations on Friction Melt Bonding of Aluminium-steel lap Joints. [Final Year Project] (Submitted)

PALANISAMMY, KALIDASAN (2013) THERMOELECTRIC AIR COOLING FOR CAR. [Final Year Project] (Unpublished)

PALU, THIRUKKUMARRAN (2021) SIMULATION OF GASIFICATION PROCESS FOR OIL PALM BASED BIOMASS PELLETS USING MATLAB. [Final Year Project] (Submitted)

PARAMAGURU, DHANIS (2019) INVESTIGATION OF UNDERWATER FRICTION STIR WELDING ON 5052 ALUMINIUM ALLOY TO OPTIMIZE THE JOINT STRENGTH. Masters thesis, Universiti Teknologi PETRONAS.

PATIL, NAMDEV ASHOK (2021) CHARACTERIZATION AND PARAMETER OPTIMIZATION OF FRICTION STIR PROCESSED AA7075 HYBRID SURFACE COMPOSITES. Doctoral thesis, UNSPECIFIED.

PATTHI, HAMDAN (2013) DEVELOPMENT OF EXCEL-BASED RELIABILITY MODEL FOR SYSTEMS WITH INCREASING/DECREASING FAILURE RATES. [Final Year Project] (Unpublished)

PATTHI, UMAR (2013) INVESTIGATION OF PHYSICAL AND MECHANICAL PROPERTIES OF FRICTION STIR WELDING ON ALUMINUM 6092/SIC/25P/T6 WELDED PLATES. Masters thesis, UTP.

PAU , JION SEAN (2014) TWO PHASE FLOW IN CO2/BRINE SYSTEM WITH SALT PRECIPITATION. Masters thesis, Universiti Teknologi PETRONAS.

PEREIRA, ROBERT HARJONI (2009) SELECTION AND ANALYSIS OF ENGINE OF FSAE 2010. [Final Year Project] (Unpublished)

PERUMAL, PRASSHANTH (2017) Evaluation of Hybrid System for Domestic Power Generation by Harvesting of Rainwater. [Final Year Project]

PING, KAM CHONG (2016) EXPERIMENTAL AND NUMERICAL INVESTIGATION ON THE ENHANCEMENT OF NATURAL UP DRAFTING IN A CHIMNEY. [Final Year Project] (Submitted)

PUI , WEI JUI (2010) Effect of Recycling on Mechanical Behaviours of Coconut-HDPE Biocomposite. [Final Year Project] (Unpublished)

PUSPITASARI, DEWI (2018) THE INFLUENCE OF STRESS RELIEVING PARAMETERS ON THE PROPERTIES OF CLOSED-CELL ALUMINIUM ALLOY FOAM. Masters thesis, Universiti Teknologi PETRONAS.

PUTRA RIFEMI, YASSER (2011) DESIGN AND DEVELOPMENT OF A RUNNING CHASSIS FOR A SIMPLE VEHICLE (BRAKE, SUSPENSION, STEERING SYSTEM). [Final Year Project] (Unpublished)

Paarthiban a/l Gunnasegaran, Paarthiban (2011) Loss Circulation Material in Drilling Fluid. [Final Year Project] (Unpublished)

Padil, Syariza Fadli Ansary (2021) Development of Halloysite Nanotube As The Future Coating Inhibitor Against Corrosion. [Final Year Project] (Submitted)

Pang , Chang-Tze (2016) Investigation of Factors Affecting Performance of Solar Still. [Final Year Project] (Submitted)

Paramaguru, Dhanis (2019) Investigation on Underwater Friction Stir Welding of 5052 Aluminium Alloy to Optimize the Joint Strength. Masters thesis, Universiti Teknologi PETRONAS.

Paramaguru, Dhanis (2016) CFD Simulation of Temperature and Humidity Distribution over Large Manufacturing Facilities. [Final Year Project] (Submitted)

Past Year Exam Question (2013) MBB 1052 MCB 1012 INTRODUCTION TO MATERIAL SCIENCE. [Past Year Examination Question]

Past Year Exam Question (2014) MBB 4423 CORROSION ENGINEERING. [Past Year Examination Question]

Past Year Exam Question (2013) MCB 1033 MBB 2083 ELECTRICAL POWER AND MACHINES. [Past Year Examination Question]

Patapal Naidu, Daanesh Naidu (2022) Modelling and Analysis of Solar Hybrid Fuel Cell Propulsion System for Autonomous Unmanned Surface Vessel. [Final Year Project] (Submitted)

Patthi, Umar (2013) Physical and Mechanical Properties Friction Stir Welding on Aluminium 6092/Sic/25p/T6 Welded Plates. Masters thesis, Universiti Teknologi PETRONAS.

Patthi, Ahmad Farid (2021) THE INFLUENCE OF COMBUSTION PROCESS PARAMETER ON THE FORMATION OF SILICA FROM OIL PALM EMPTY FRUIT BUNCH (OPEFB). [Final Year Project] (Submitted)

Pau , Shang Pei (2010) Study of Liquid Flow with Bubbles in Pipes. [Final Year Project] (Unpublished)

Pauzi, Muhamad Farith (2015) Study of Low Stiffness Resilient Shaft (LSRS). [Final Year Project] (Unpublished)

Peng Sheng, Lim (2013) Modelling of Axial Spring Stiffness in Active Vibration Controlled Drilling. [Final Year Project] (Unpublished)

Ping, See Itt (2016) Investigation of Charging and Discharging Process in a Rotating Latent Heat Storage. [Final Year Project] (Submitted)

Prathom Suwanno A/L Pet, Prathom Suwanno (2010) Study on Microstructure and Mechanical Properties of Traditional Keris Blade. [Final Year Project] (Unpublished)

Premchand, Saswen (2022) The effect of plunge depth on the fabrication of base and mono composites of AZ91 Using friction stir processing. [Final Year Project] (Submitted)

Q

QAYYUM, JUNAID AHMAD (2018) ENHANCEMENT STUDY OF POLYMER RAPID TOOLING FOR METAL INJECTION MOLDING. Masters thesis, Universiti Teknologi PETRONAS.

QING, LIM JIA (2017) Solid-state Air Conditioning System for Electric Vehicle Application. [Final Year Project]

Qais Abro, Mohammad Amer (2010) Computational Fluid Dynamics study of Airflow through a Car's Radiator. [Final Year Project] (Unpublished)

Quartos Radintletse Maremo Mamabolo, Quartos (2010) Design Of A Heat Recovery System For Bio-Oil Upgradation. [Final Year Project] (Unpublished)

Qurratu’aini Binti Ismail, Qurratu’aini (2010) Melt Flow Analysis of Novel Polymer Plate Washer Using Computational Fluid Dynamic (CFD). [Final Year Project] (Unpublished)

R

R Selvaraja, Skandha Kumar (2022) The Corrosion Behaviour of Glass Fibre Reinforced Polymer Strengthened Steel Under High Temperature Environment. [Final Year Project] (Submitted)

R Sundaram, Ranjiivan (2020) Curing Methods on Early Strength of Geopolymer Concrete. [Final Year Project] (Submitted)

RAFIQ, SIKANDER (2013) SYNTHESIS, CHARACTERIZATION AND EVALUATION OF MIXED MATRIX MEMBRANES FOR C02 SEPARATION. PhD. thesis, Universiti Teknologi PETRONAS.

RAJA, NAVIN (2021) CRASHWORTHINESS ANALYSIS OF TRAPEZOID 3D ORIGAMI CRASH STRUCTURE. [Final Year Project] (Submitted)

RAMAN, MOGANES (2023) DEVELOPMENT OF MECHANICALLY REINFORCED EFB-CG (EMPTY FRUIT BUNCH-CHITOSAN GRAPHENE) COMPOSITE FOR MERCURY ADSORPTION. Masters thesis, UNSPECIFIED.

RAMLEE, EZWANI (2022) ENHANCING THE MECHANICAL PROPERTIES OF LOW-CARBON STEEL BY GAS NITRIDING: ANALYSIS BY ANOVA. Masters thesis, UNSPECIFIED.

RAMLI, MUHAMMAD NURSHAFIQ (2020) Effects of Geometrical Dimension and Tolerance and Material Properties on Vibration and Torque Performance of Novel Torque Boosting Device. Masters thesis, Universiti Teknologi PETRONAS.

RASIP, NASIRUDDIN ZHARIFF (2013) DESIGN FOR MANUFACTURING WITH RAPID PROTOTYPING. [Final Year Project] (Unpublished)

RAVI, RUBEN (2021) Chloride Induced Stress Corrosion Cracking For Thermally Insulated Austenitic Stainless Steel Type 304 Using Wick Test. [Final Year Project] (Submitted)

RAZA, TAHIR (2017) DEVELOPMENT OF MAINTENANCE PERFORMANCE MEASUREMENT FRAMEWORK FOR PETROCHEMICAL INDUSTRY. Masters thesis, Universiti Teknologi PETRONAS.

RAZAK, ARIFF QAMARUDDIN (2020) FAILURE ANALYSIS OF POLYVINYLIDENE FLUORIDE BY DEGRADATION FOR A PIPELINE. [Final Year Project] (Submitted)

RAZALI, MOHAMAD FIRDAUS (2013) COOPERATIVE MANIPULATORS. [Final Year Project] (Unpublished)

RAZALI, MOHD SAIFUL IZW AN (2011) DEVELOPMENT OF A SYSTEM FOR COOLING INLET AIR FOR GAS TURBINE USING CHILLED WATER. [Final Year Project] (Unpublished)

RAZMANI, RADHI (2017) OPTIMIZATION STRATEGY IN ENERGY SAVING OF CHILLER PLANT SYSTEMS. [Final Year Project] (Submitted)

REDUAN, ALLYA RADZIHAN BINTI REDUAN (2013) Performance Investigation of Transcritical Carbon Dioxide Refrigeration Cycle. [Final Year Project] (Unpublished)

REMESH, SATHANISWARMAN (2021) Development of Oil Palm Lignin-Derived LSG Infused with Nanoadditives for Potential Supercapacitor Application. [Final Year Project] (Submitted)

RESHID, MESERET NASIR (2013) AVAILABILITY MODEL FOR A COG EN ERA TION SYSTEM SUBJECTED TO REDUNDANCY. PhD. thesis, UTP.

RIDZUAN, ANAS FADHIL (2018) FATIGUE ANALYSIS OF FREE STANDING DRILLING RISER DUE TO VORTEX INDUCED VIBRATION UNDER EXTREME WEATHER CONDITIONS. [Final Year Project] (Submitted)

RIZLAN, MUHAMAD ZULKHALRI (2013) ESTABLISHING POSSIBLE MECHANISMS FORPRODUCING NANOPARTICLES OF TRONOH SILICA SAND VIA LOW SPEED MECHANICAL MILLING PROCESS. Masters thesis, UTP.

ROFFIE, ZUBAIRI FARIHAN (2012) FINITE ELEMENT MODELING OF THICK WALLED VESSELS UNDERGOING LOCALIZED POST WELD HEAT TREATMENT. [Final Year Project] (Unpublished)

ROSHIDA HASSAN JAMIL, ROSHIDA (2008) Design of Experiment on Ultra Violet Curing Die Attach Film by Using Taguchi Method to Optimize Quality. [Final Year Project] (Unpublished)

ROSLAN, MUHAMMAD SHAFIQ (2011) Aerodynamics Optimization of the Univeniti Teknologi PETRONAS 'PERODUA Eco-ChaUenge 2011' Car. [Final Year Project] (Unpublished)

ROSLI, MOHD ARIF FAHMI (2020) EXPERIMENTAL INVESTIGATION OF DROPLET EVAPORATION AND MICRO EXPLOSION BEHAVIOUR OF GAS-TO-LIQUID (GTL) FUEL. Masters thesis, Universiti Teknologi PETRONAS.

ROSLI, MUHAMAD FADHLI (2020) DEVELOPMENT OF PREDICTION MODELS OF OIL & GAS PIPELINE SUBJECT TO CORROSION USING REGRESSION TECHNIQUES. Masters thesis, Universiti Teknologi PETRONAS.

ROSLI, RHAISHAZRIN AMIRUL IQMA (2013) Gear Faults Analysis Using Finite Element Method. [Final Year Project] (Unpublished)

ROSMAN, MUHAMMAD AIZADT (2017) TEMPERATURE PREDICTION IN HOT TAPPING PROCESS FOR HIGH PRESSURE PIPELINE. [Final Year Project]

RUSLI, MOHAMAD FITRI (2009) FAILURE ANALYSIS STUDY ON THE CUTTER BLADE OF POLYPROPYLENE PELLETER DRIVE. [Final Year Project] (Unpublished)

Rabie, Fatthie Khairullah Hishyam (2016) INFLUENCE OF TEMPERATURE ON STABILITY OF ALUMINUM FOAM CELL WALL DURING FOAMING PROCESS. [Final Year Project]

Raffisyazana Binti Romli, Raffisyazana (2010) Performance Evaluation of Various Biomasses in a Gasifier Based Cook Stove. [Final Year Project] (Unpublished)

Ragab Mousa, Mahmoud Shehata AbdAlfatah (2016) Experimental Evaluation of Zero Energy PG Office Under Natural and Forced Ventilation. [Final Year Project] (Submitted)

Ragupathy, Panjaabegesan (2013) DIGITAL IMAGE CORRELATION APPLICATION IN TENSILE TEST FOR ALUMINIUM ACCORDING TO ASTM E-8 STANDARD. [Final Year Project] (Unpublished)

Rahiman, Raieza Hanim (2008) Investigation on Lost Circulation Materials (LCM) Derived From Dorian Peel Waste For Drilling Fluid Formulation. [Final Year Project] (Unpublished)

Rahmad, Muhammad Faruqi (2015) Risk-based Inspection Model for Atmospheric Storage Tank. [Final Year Project] (Unpublished)

Rahmat, Abdul Hazim (2010) Improvement of Engine Performance to Reduce Fuel Consumption of a Single Cylinder Spark Ignition Engine. [Final Year Project] (Unpublished)

Raieza Hanim Rahiman, Raieza Hanim (2008) Investigation on Lost Circulation Materials (LCM) Derived From Durian Peel Waste For Drilling Fluid Formulation. [Final Year Project] (Unpublished)

Rais, Md Aidi (2002) Investigation of Thermal Properties of Radiation Grafted Polystyrene / Polytetrafluoroethylene (PTFE) Copolymer Films. [Final Year Project] (Unpublished)

Raja Faeez Shah Bin Raja Mudzaffar Shah, Raja Faeez Shah (2008) Design of A Steering Mounted Paddle Shifter for A Racing Car. [Final Year Project] (Unpublished)

Raja Mohamed Abdul Shaini, Raja Mohamed Rizal (2012) Performance of the Single and Double Pass V-Groove Solar Collector. [Final Year Project] (Unpublished)

Rajaindren, Navindran (2014) Siliconizing of Aluminium Alloys via Silica Sand Bath. [Final Year Project] (Unpublished)

Ramachanderan, Mageshwaran (2016) Development and Char Morphology Analysis of Siloxane Based Intumescent Fire Retardant Coatings. [Final Year Project] (Submitted)

Ramadan, Wani James (2015) Enhancement of refrigeration performance with an ejector. [Final Year Project] (Unpublished)

Ramah Moorthy, Kuhaneswaren (2012) Screening Model for CO2 Miscible Flooding. [Final Year Project] (Unpublished)

Ramasamy, Guna (2015) Determination Of Optimum Proportional-Integral-Derivative (PID) Controller Gain Values For Autonomous Underwater Vehicle (AUV). [Final Year Project] (Unpublished)

Ramlan, Nur Amalina (2015) Effect of Physical Fiber Lay of FRP Winding Composite on Mechanical Properties. [Final Year Project] (Unpublished)

Ramli, Amir Qayyum (2021) TO DESIGN A COMPREHENSIVE ENGINEERING TRAINING MODULE USING SWANSOFT CNC SIMULATOR. [Final Year Project] (Submitted)

Ramli, Meor Ahmad Saiful Ridhwan (2012) Modelling of Hydrates in Subsea Pipeline. [Final Year Project] (Unpublished)

Ramli, Muhammad Hamizan (2014) Siliconizing Of Thermoplastic via Silica Sand Bath. [Final Year Project] (Unpublished)

Ramli, Muhammad Nurshafiq (2016) Analyze Performance of Torque Boosting Device. [Final Year Project] (Submitted)

Ramli, Syaida Hazira (2012) CFD SIMULATIONS OF ANNULAR DISTRIBUTOR OF SWIRLING FLUIDIZED BED (SFB) REACTOR. [Final Year Project] (Unpublished)

Ramly, Mohammad Zuhairi (2008) The Design and Fabrication of a prototype machine: "asam gelugor" processing machine. [Final Year Project] (Unpublished)

Rani, Mohd Sufiyan (2011) POWER MANAGEMENT DEVICE FOR AUTOMOTIVE BATTERY. [Final Year Project] (Unpublished)

Rao, Syam Sundhara (2015) DYNAMIC RESPONSE OF SPAR PLATFORM SECURED WITH MOORING SYSTEM USING ANSYS-AQWA. [Final Year Project] (Unpublished)

Rashid, Amirah Binti (2009) Design of pico hydro turbine for remote areas. [Final Year Project] (Unpublished)

Raudhah Binti Ab Majid, Raudhah (2010) Design and Development of an Innovative Flat Plate Solar Collector. [Final Year Project] (Unpublished)

Ravevarman, Puviin Varman (2020) Degradation and Characterization of Bio-Waste Reinforced Polymer Composite. [Final Year Project] (Submitted)

Ravi Chandran, Meveeqhen (2020) Simulation Study on Utilisation of Biogas from Palm Oil Mill Effluent (POME) as Fuel for Diesel Generator Set. [Final Year Project] (Submitted)

Razak, Mohamad Amin (2010) Characterization of Various Biomass Sources for Co-Gasification. [Final Year Project] (Unpublished)

Razak, Mohamad Amin (2010) Characterization of Various Biomass Sources for Co-Gasification. [Final Year Project] (Unpublished)

Razalee, Muhammad Reezwan Shah (2020) RELATIVE ATTACK ANGLE OF FIN AFFECTS THE CONVECTIVE HEAT TRANSFER. [Final Year Project] (Submitted)

Razali, Muhamad Faezi (2022) Theoretical Investigation on The Shallow Ground Thermal Profiling Under Dry and Wet Weather Conditions. [Final Year Project] (Submitted)

Razali, Luqman Hakim (2011) NEW CELLULOSIC-BASED ACOUSTIC WALL BOARD MATERIAL FROM PAPER WASTE. [Final Year Project] (Unpublished)

Razali, Mohamad Amir (2017) Life Cycle Assessment of Heat Recovery Steam Generator. [Final Year Project]

Razali, Mohamad Firdaus (2013) COOPERATIVE MANIPULATORS. [Final Year Project] (Unpublished)

Razlan, Muhammad Fudzail (2013) Coordination of Multiple Mobile Robots. [Final Year Project] (Unpublished)

Reisinafchi, Behnam (2017) Research on New Approach to Patient Specific Instruments for Improving Mechanical and Anatomical Alignment Accuracy during Total Knee Arthroplasty. [Final Year Project] (Submitted)

Richard, Grace (2022) Study of Indoor Air Quality at Hostel Rooms in the Presence of Natural Ventilation. [Final Year Project] (Submitted)

Richard, Grace (2022) Study of Indoor Air Quality at Hostel Rooms in the Presence of Natural Ventilation. [Final Year Project] (Submitted)

Rima Rafiza A. Malik, Rima Rafiza (2010) Study into the Effect of Crude Palm Oil (CPO) as a Cutting Fluid on the Tool Wear and Chip Formation during Lathe Cutting Operation. [Final Year Project] (Unpublished)

Riswan, Fatin Nabilah (2015) Investigation on Effect of Distance between Tanks on Fire Spread in Oil Refinery. [Final Year Project] (Unpublished)

Rizal Nikman, Erhan Nikman (2013) Preliminary investigation of corrosion surfaces under coating on a plate using IR thermal imaging camera. [Final Year Project] (Unpublished)

Rizal Nikman, Erhan Nikman (2013) Preliminary investigation of corrosion surfaces under coating on a plate using IR thermal imaging camera. [Final Year Project] (Unpublished)

Rizlan, Muhamad Zulkhairi (2015) Nanoparticles Production of Tronoh Silica Sand via Low Speed Mechanical Milling Process. Masters thesis, Universiti Teknologi PETRONAS.

Rodzi, Mohd Faiz (2015) Front End Engineering Design for Offshore Facility Equipment. [Final Year Project] (Unpublished)

Rohaizam bin Abd Rahman, Rohaizam (2009) Study on Thermal Degradation Effects on Physical Property of Polymers. [Final Year Project] (Unpublished)

Romenor, Muhammad Rafaee (2012) MODEL OF COLLABORATION BETWEEN SUPPLIER AND MANUFACTURER FOR THE PROFIT OF SUPPLY CHAIN. [Final Year Project] (Unpublished)

Romenor, Muhammad Rafaee (2012) MODEL OF COLLABORATION BETWEEN SUPPLIER AND MANUFACTURER FOR THE PROFIT OF SUPPLY CHAIN. [Final Year Project] (Unpublished)

Romenor, Muhammad Rafaee (2012) MODEL OF COLLABORATION BETWEEN SUPPLIER & MANUFACTURER FOR THE PROFIT OF SUPPLY CHAIN. [Final Year Project] (Unpublished)

Rosdi, Fatin Amalina (2013) Enhancement of Materials Surface Properties via Case Hardening Process: Metals Substrate in Silica Sand Bath. [Final Year Project] (Unpublished)

Rosdi, Syarizatul Nadia (2008) Application of Solar Energy in Drying Pepper. [Final Year Project] (Unpublished)

Roslan, Muhammad Hafiz (2015) INVESTIGATION OF FIRE RESISTANT PROPERTIES OF GLASSWOOL AND ROCKWOOL HYBRID FIBRE REINFORCED INTUMESCENT COATING. [Final Year Project] (Unpublished)

Roslan, Rabiatul Adawieah (2016) TORREFACTION OF EMPTY FRUIT BUNCH IN BIOMASS COMBUSTION GAS. [Final Year Project]

Roslan, Rozanna (2015) Effect of Different Roof Materials on Energy Savings and Carbon Dioxide Reductions for Rainwater Harvesting Systems. [Final Year Project] (Unpublished)

Rosli, Ahmad Aizat (2013) INVESTIGATION OF THE IMPACT OF IMPERFECTION REPAIR AND MAINTANENCE TO SYSTEM AVAIBILITY. [Final Year Project] (Unpublished)

Rosli, Mohd Zaki AI Hafiz (2008) Mnltitask Anti-Dust Cleaner. [Final Year Project] (Unpublished)

Roslim, Muhammad Thaqif (2008) Experimental Study on Scale Control in Surface Pipelines by Magnetic Descaler. [Final Year Project] (Unpublished)

Rosni, Muhammad Syafiq (2014) Experimental Works and Analysis to Determine the Degradation of Permanent Magnet Force under Cyclic Magnetic Field. [Final Year Project] (Unpublished)

Rosnizam, Nur Izzah Farzana (2021) Effect of Fluid Velocity and Sand Flowrate on The Intrusive Erosion Probe Using 3D Computational Method. [Final Year Project] (Submitted)

Roszopor, Nurul Atiqah (2011) Assessment of Process Capability Using Weibull Analysis. [Final Year Project] (Unpublished)

Rozibab, Mohd. Kamalmursyid (2009) Sliding of Elastically Similar Complete Contacts. [Final Year Project] (Unpublished)

Rozli, Megat Fazli (2009) Design, Rapid Prototyping and Testing of the Wells Turbine. [Final Year Project] (Unpublished)

Ruba’ai, Nur Amira (2015) A Study on the Performance of Splash Zone. [Final Year Project] (Unpublished)

Rubiah Binti Ab Ghani, Rubiah (2010) Study into the Effect of Crude Palm Oil (CPO) as a Cutting Fluid on the Surface Finish and Roundness During Lathe Cutting Operation. [Final Year Project] (Unpublished)

Ruslan, Ibtihal (2016) Parametric Study on Effectiveness of Heat Exchangers for Primary and Secondary Chilled Water Distribution Lines of an Academic Complex. [Final Year Project] (Submitted)

Ruslan, Razin Akmal (2015) Energy Harvesting Using Mechanical Absorber. [Final Year Project] (Unpublished)

Ruslan, Rifdi Zulfadhli (2011) Characterisation of Voids in a Polymer Composite Wind Turbine Blade Manufactured via Resin Infusion Process. [Final Year Project] (Unpublished)

Ruzanna Binti Abu Bakar, Ruzanna (2010) Computer Aided Design of Semi-submersible for Deepwater Operations. [Final Year Project] (Unpublished)

S

S/O Naranasamy, Arjun Raj (2016) Investigation on Filter Mechanism for Air Polluted Environment. [Final Year Project] (Submitted)

SABIR, OSAMA FUAD AKASHA (2018) Cell by Cell Artificial Neural Networks Approach for Modelling Laminar Flow in Two-dimensional Domain. PhD. thesis, Universiti Teknologi PETRONAS.

SAEID, KAKOOEI (2013) DESIGN AND FABRICATION OF A SURFACE pH SENSOR FOR A REAL TIME CORROSION MONITORING. PhD. thesis, Universiti Teknologi PETRONAS.

SAFIYULLAH, FEROZKHAN (2015) COMPUTATIONAL MODELING OF GAS COMPRESSOR DIAGNOSTICS USING GENETIC PROGRAMMING. Masters thesis, Universiti Teknologi PETRONAS.

SAHAR, MOHAMAD ISKANDAR (2013) Vehicle Body Design and Analysis of a Practical, Fuel Efficient City Concept Car. [Final Year Project] (Unpublished)

SAHEED OLALEKAN, WASIU (2013) STUDY OF DIRECT INJECTION COMPRESSED NATURAL GAS ENGINE EMPLOYING EXHAUST GAS RECIRCULATION WITH HYDROGEN GAS AS A DUAL FUEL. PhD. thesis, Universiti Teknologi PETRONAS.

SAID ALI, BASIL HASSAN (2018) DEVELOPMENT OF AN OPTIMUM SOLAR POWER TOWER MODEL USING EVACUATED TUBE RECEIVER. PhD. thesis, Universiti Teknologi PETRONAS.

SAIPUDDIN, NURAMALINA (2016) PERFORMANCE ASSESSMENT OF AN OFF DESIGN AIR FINNED COOLER. [Final Year Project] (Submitted)

SAJID, ZUBAIR (2021) BEARING PERFORMANCE IMPROVEMENT OF SINGLE-LAP, SINGLE-BOLT CARBON/BASALT HYBRID FIBER-REINFORCED COMPOSITE JOINTS. Doctoral thesis, UNSPECIFIED.

SALEM BASYOAL, OMAR AHMED (2016) Prediction of Cooling Load of a Glazed Building under Malaysia Weather Conditions. [Final Year Project] (Submitted)

SALIH AHMED, MOJAHID SIDAHMED MOHAMMED (2014) DEVELOPMENT OF A DYNAMIC SIMULATOR FOR DOUBLE-EFFECT COMMERCIAL STEAM ABSORPTION CHILLER. PhD. thesis, Universiti Teknologi PETRONAS.

SALIM, MOHAMMAD RAZISW ADY (2008) Experimental Modeling ofthe Flow in the Furnace Top of an Ethane Cracker at EPEMSBPaka. [Final Year Project] (Unpublished)

SAM, BAN (2017) NUMERICAL SIMULATION OF TWO-PHASE SLUG FLOW REGIME IN HORIZONTAL PIPE. Masters thesis, Universiti Teknologi PETRONAS.

SARU @ SARUDDIN, MUHAMMAD ZUL „AFIF (2013) ENHANCEMENT OF MATERIALS SURFACE PROPERTIES VIA SURFACE COATING PROCESS: POLYMER SUBSTRATE IN SILICA SAND BATH. [Final Year Project] (Unpublished)

SARWAR, UMAIR (2015) FAULT DIAGNOSIS MODEL FOR ROTATING MACHINERY BASED ON MULTIPLE CONDITION MONITORING DATA SOURCES. Masters thesis, Universiti Teknologi PETRONAS.

SAW, CHUN LIN (2013) PERFORMANCE INVESTIGATION OF SOLAR WATER HEATER INTEGRATED WITH PCM AND PCM NANOCOMPOSITE THERMAL ENERGY STORAGE. PhD. thesis, Universiti Teknologi PETRONAS.

SAZALI, SYAZWAN (2016) Vortex Induced Vibration (VIV) Reduction Measure on Dimpled Concrete Coated Pipeline. [Final Year Project] (Submitted)

SA’AT, MOHD NAJIB (2013) THERMAL CHARACTERIZATION OF JATROPHA BASED BIODIESEL BLEND WITH FOSSIL DIESEL USING TGA. [Final Year Project] (Unpublished)

SEENI MOHAMED, MUHAMMAD ANWAR IBRAHIM (2017) IMPROVING PATIENT'S SATISFACTION USING LEAN HEALTHCARE AND KANO MODEL. [Final Year Project]

SEVALOGA NATHAN, LOGESWARY (2009) ANALOGY OF MECHANICAL AND TRANSPORT PROPERTIES IN DISPERSE COMPOSITES. [Final Year Project] (Unpublished)

SHAHIR, ADIB ZULFADHLI (2011) Cold and hot water plumbing system on living quarters in an offshore platform. [Final Year Project] (Unpublished)

SHAHIR BIN AHMAD SABRI, SHAHIR (2012) EFFECT OF THE INTERNAL FLUID FLOW IN THE GLASS FIBRE REINFORCED PLASTIC (GFRP) DYNAMIC. [Final Year Project] (Unpublished)

SHAHROL AZRAI, FARID AIMAN (2020) Electrochemical Impedance Evaluation Of Coating Under Simulated Splash Zone Condition. [Final Year Project] (Submitted)

SHAIK, NAGOOR BASHA (2021) PIPE CONDITION PREDICTION MODELS FOR OIL AND GAS PIPELINES USING ARTIFICIAL NEURAL NETWORKS. Doctoral thesis, UNSPECIFIED.

SHAMSHIRGARAN, SEYEDREZA (2019) TECHNO-ECONOMIC OPTIMIZATION OF BIO-NANOFLUID-BASED SOLAR FLAT-PLATE COLLECTORS. PhD. thesis, Universiti Teknologi PETRONAS.

SHAMSUDDIN, NAWAL (2011) Study of Carbon Dioxide Corrosion on Carbon Steel at Different Salt Concentrations. [Final Year Project] (Unpublished)

SHAMUGAM, JAYKANESH (2013) THERMAL SHRINKAGE AND GAS VOIDS FORMATION OF WAXY CRUDE OIL. [Final Year Project] (Unpublished)

SHAO ZHE, JOSH WONG (2015) Optimization Strategy & Energy Savings Of Water-Cooled Chiller Plant System. [Final Year Project] (Unpublished)

SHARANAGOUDA PATIL, SANTOSH (2017) Evaluation of Frictional Contact Stresses in Spur and Helical Gears. PhD. thesis, Universiti Teknologi PETRONAS.

SHARIFF, MOHD FARITH (2012) HEAT SHIELDING PERFORMANCE OF MINERAL BASED INTUMESCENT FIRE RETARDANT COATING. [Final Year Project] (Unpublished)

SHARIFUTDIN, NUR SALAM (2013) A STUDY OF TORQUE VECTORING AND TRACTION CONTROL FOR A PARALLEL SPLIT HYBRID ELECTRIC VEHICLE. [Final Year Project] (Unpublished)

SHIRAZI, MUHAMMAD IRFAN (2014) FIBER ORIENTATION IN METAL INJECTION MOLDED SHORT CARBON FIBER REINFORCED COPPER MATRIX COMPOSITE. Masters thesis, Universiti Teknologi PETRONAS.

SHOZIB, IMTIAZ AHMED (2021) INVESTIGATION OF ELECTROLESS Ni-P-TiO2 COMPOSITE COATING ON AA7075 FOR SURGICAL TOOLS APPLICATION. Masters thesis, Universiti Teknologi PETRONAS.

SHU LIANG, HO (2018) Performance Analysis of 150cc Single Cylinder Engine with Electronic Fuel Injection System. [Final Year Project] (Submitted)

SHUKRI, FADHIL AIZAD (2018) CFD STUDY ON EFFECTS OF DIFFERENT WINDOW FILMS ON THE COOLING RATE OF ACADEMIC BUILDINGS IN UNIVERSITY TECHNOLOGY PETRONAS (UTP). [Final Year Project] (Submitted)

SINGH, HARNAMDAV (2011) STUDY ON CHAR EXPASION AND HEAT SIDELDING OF INTUMESCENT COATING BASED ON INORGANIC FILLERS. [Final Year Project] (Unpublished)

SIONG, HO CHIT (2013) Modelling and Simulation of Oil Production Tubing Dynamic and Static Characteristics due to Fluid Dynamic Loading. [Final Year Project] (Unpublished)

SITTI KHADIJAH BT SHAHUL HAMID, SITTI KHADIJAH (2011) DEVELOPMENT AND MICROSTRUCTURAL ANALYSIS OF CARBON NANOTUBES REINFORCED COPPER MATRIX NANOCOMPOSITES USING PIM TECHNIQUE. [Final Year Project] (Unpublished)

SIVALINGAM, GEENEISH (2014) STUDY ON THE MANUEVERABILITY OF AN UNDERWATER GLIDER WITH APPENDAGES. [Final Year Project] (Unpublished)

SUBRAMANIAM, KRISHNAN (2017) Range of Motion (ROM) Induced by Shape Memory Alloy (SMA) Actuation on Stewart Platform for Foot/Ankle Rehabilitation. PhD. thesis, Universiti Teknologi PETRONAS.

SUBRAMANIAN, VISALACHY (2017) REMOVAL OF IMPURITIES FROM MILLED AMORPHOUS SILICON DIOXIDE THROUGH THERMAL ANNEALING AND ACID LEACHING USING TAGUCHI METHODS FOR 3C SILICON CARBIDE PHOTOVOLTAIC APPLICATION. [Final Year Project]

SUFFIAN, MUHAMMAD HAZIM (2013) TOWARDS A MORE ACCURATE FLOW RATE ESTIMATION TECHNIQUE FOR OIL SPILLS FROM PIPELINES. [Final Year Project] (Unpublished)

SULAIMAAN, ISFAHAN AMIN (2015) DESIGN AND HEAT TRANSFER ANALYSIS OF A FINNED INNER TUBE DOUBLE PIPE HEAT EXCHANGER. [Final Year Project] (Unpublished)

SULAIMAN, AHMAD NURAIZAT (2012) THERMODYNAMIC ANALYSIS OF GAS TURBINE. [Final Year Project] (Unpublished)

SYAH LUBIS, ABDUL MUNIR HIDAYAT (2013) TRIBOLOGICAL Sl1JDY OF JATROPHA (Jatropha carcass L) OIL AS ECO-FRIENDL Y BOUNDARY LUBRICANT. PhD. thesis, UTP.

SYAZANA BT NADZIR, SYAZANA (2010) Mathematical Modelling, Computation & Analysis of Oil Pipeline Buckling. [Final Year Project] (Unpublished)

Saad, Muhammad Syauqie (2022) Steam Properties Prediction in Steam Pipeline System using Microsoft EXCEL VBA. [Final Year Project] (Submitted)

Saari, Nurul Aimi (2014) Evaluation of Reformer Tubes Degradation after Long Term Operation. [Final Year Project] (Unpublished)

Sabri, Shafiq Hakimi (2012) Conceptual Design Support Tool For Subsea Equipment Processing System. [Final Year Project] (Unpublished)

Sabrumdin, Nor Naillriya (2009) Stress Analysis of Riser using Finite Element Method (FEM). [Final Year Project] (Unpublished)

Sadhik Batcha, Mohd Ansar (2021) Determining Reduction of Diesel Fuel Consumption When Using Emulsified Biodiesel Fuels Derived from Palm Oil. [Final Year Project] (Submitted)

Sadig, Hussain (2015) The Effect of Producer Gases on The Performance and Emissions of a Micro-Gas Turbine. Doctoral thesis, Universiti Teknologi PETRONAS.

Safwan Hanis Bin Mohd Murad, Safwan Hanis (2009) Study of a New Air Intake System for a Single Cylinder, Fuel Injection, 4 stroke Go-Kart engine. [Final Year Project] (Unpublished)

Sahar, Nurizuan (2009) Solar Curing of Glass Fibre Reinforced Epoxy (GRE) Composite. [Final Year Project] (Unpublished)

Sahardin, Abdul Malek (2016) Fabrication of Iridium Oxide Screen Printed pH Sensor for Microbial Induced Corrosion Monitoring Application. [Final Year Project] (Submitted)

Sahari, Nurul Syahirah (2022) Finite Element Analysis of Belleville Spring Stiffness Behaviour. [Final Year Project] (Submitted)

Saharudin, Muhammad Naim Al Amin (2013) A STUDY OF ALUMINUM HONEYCOMB IMPACT ATTENUATOR FOR NEIGHBORHOOD ELECTRIC VEHICLES. [Final Year Project] (Unpublished)

Said, Nurfatin (2011) Three-Dimensional Reconstruction of Friction Stir Welding Microstructure via Serial Sectioning. [Final Year Project] (Unpublished)

Saidun, Mohammad Razif (2005) Ball feeder mobile robot with remote control / by Mohammad Razif B. Saidun, TJ 211.415 .M697 2005. [Final Year Project]

Saifuddin, Ahmad Syahir (2020) Numerical Study Of Nanofluids Assisted Thermoelectric Air Conditioner. [Final Year Project] (Submitted)

Saiful Aznan, Muhammad Zulhilmi (2008) Analysis on electrical power requirement of a hybrid solar-electric oven. [Final Year Project] (Unpublished)

Saiful Bahri, Laila Izyana (2016) Thermodynamic Analysis of Organic Flash Cycle (OFC) for Power Generation from Low to Medium Heat Sources. [Final Year Project] (Submitted)

Saleh Bin Hashim, Saleh (2009) Reduction of Noise Generated by Electric Motor in Typical Home Appliance Casing. [Final Year Project] (Unpublished)

Salehuddin, Muhammad Hazeeq (2013) Effect of Varying Air Flow and Types of Paper on Heat Exchanger of Energy Recovery System. [Final Year Project] (Unpublished)

Salim, Muhammad Shahrul Izzwan (2020) CRACK PREDICTION OF USING FINITE ELEMENT ANALYSIS. [Final Year Project] (Submitted)

Sallahuddin, Ahmad Nadzrin Shah (2013) Development of an Excel Based Spreadsheet of Analytical Hierarchy Process And Decision Making Grid For Maintenance Policy Decision. [Final Year Project] (Unpublished)

Samin, Mohd Shamam (2004) DESIGN OF MOTORCYCLE ENGINE COMPONENTS BASED ON FIXED SPECIFICATION. [Final Year Project] (Unpublished)

Samsudin, Mohammad Syafiq (2010) Preparation of Oil Palm Frond (OPF) for biomass Gasification. [Final Year Project] (Unpublished)

San, Lye Siew (2015) Design and Fabrication of Curb-Climbing Mechanism for a Wheelchair using 3D Printing Technology. [Final Year Project] (Unpublished)

Sandrasagar, Suresh (2020) Performance Evaluation of Vertically Oriented Compound Parabolic Concentrating Solar Collector Integrated with Heliostat Field. [Final Year Project] (Submitted)

Saniman, Amir Hakim (2015) STUDY OF RELATION BETWEEN PIN TOOL GEOMETRY WITH FORMATION OF WORMHOLE IN FSW OF ALUMINUM AA5083. [Final Year Project] (Unpublished)

Sanjay, Singh Sandhu (2022) Measurement of the water absorption on hybrid fibre waste composite and its impact on flexural performance. [Final Year Project] (Submitted)

Sarifuddin, Siti Norakma (2015) Optimization of Mechanical Properties in Natural Hybrid Polymer Composite using Polypropylene (PP), Banana Stem Fiber (BS) and Pineapple Leaf Fiber (PALF). [Final Year Project] (Unpublished)

Sasendera S/O Balamohan, Sasendera (2008) Feasibility of Oil-Palm Fronds for Biomass Gasification. [Final Year Project] (Unpublished)

Saufi B Ali, Saufi (2010) Numerical Study On The Three Dimensional Flow Of Airfoilflat Plate Combination With Gap. [Final Year Project] (Unpublished)

Saw, Soon Wei (2010) Study Of A Water Cooled Wall To Reduce Residential Indoor Temperatures At Night. [Final Year Project] (Unpublished)

Saw , Nixon Hong Ken (2016) FPSO Mooring Line Fatigue. [Final Year Project] (Submitted)

Sayid Basri, Sayid Izwan (2016) Study on Irreversible and Coefficient Performance of Double Effect Lithium Bromide and Water Steam Absorption Chiller. [Final Year Project] (Submitted)

Sayidah Nafishah binti Mohd Sabri, Sayidah Nafishah (2010) Powder Metallurgy of Copper Based Composite with Silica Sand. [Final Year Project] (Unpublished)

See Yun Chuan, See Yun Chuan (2012) Influence of Varying Rockwool Fibre Length on Properties of Intumescent Coating. [Final Year Project] (Unpublished)

Selamat, Noor Atilia (2010) Development ofBiocomposite: The Influence of Natural Fillers. [Final Year Project] (Unpublished)

Seng, Sook Harn (2013) Hydrate Formation in Multiphase Flow in Pipe. [Final Year Project] (Unpublished)

Senthilvasan, Kishaan Kumar (2021) Study On The Effect Of Contemporary Malaysian House Designs On Energy Consumption. [Final Year Project] (Submitted)

Seong, Liew Chee (2022) Axial Hydro Turbine Blade Position Configuration for Optimum Hydropower Generation. [Final Year Project] (Submitted)

Seong, Javier Teo Han (2011) Dynamic Anaiysis of Suspension Bridge. [Final Year Project] (Unpublished)

Seow , Lee Lee (2008) Energy Recovery by Conversion of Thermal Energy of Flue Gases to Electricity. [Final Year Project] (Unpublished)

Serdar Halliyev, Halliyev (2008) Relative Permeability Hysteresis. [Final Year Project] (Unpublished)

Sern, Chew Jay (2013) Wellbore Plastering during CasingwhileDrilling Prediction. [Final Year Project] (Unpublished)

Sern, Tan Yinn (2013) Experimental Studies on the Wavy Regime in Swirling Fluidized Bed. [Final Year Project] (Unpublished)

Settan, Jayashellan Vishnu (2022) Thermal Modelling and Analysis of Lithium Iron Phosphate Battery Pack in Small Electric Vehicles. [Final Year Project] (Submitted)

Sha'ari, Asmawi (2008) SIMULATION OF SINTERING IN POWDER METALLURGY APPLICATION FOR FERROUS MATERIALS. [Final Year Project] (Unpublished)

Shafie, Izzat Sayyidi (2020) Characterizations of Solid Biomass Fuel Pellets. [Final Year Project] (Submitted)

Shah Nadzri Bin Jasmir, Shah Nadzri (2010) Reliability Centered Maintenance Implementation at CUF Kertih. [Final Year Project] (Unpublished)

Shaharuddin, Muhammad Shafiq (2005) An intelligent indor plant watering system using microcontroller / by Muhammad Shafiq Bin Shaharuddin, TJ 223 .P76 M952 2005. [Final Year Project]

Shaharuddin, Syazatul Aqilah (2011) AN INVESTIGATION INTO THE CORROSION BEHAVIOUR OF ZINC AND CHROMIUM METALLIC COATING ON MILD STEEL SUBSTRATE. [Final Year Project] (Unpublished)

Shahbudin, Mohamad Khairul Azwan (2013) Glass Fiber Reinforced-Fire Retardant Composites For Offshore Platforms Application. [Final Year Project] (Unpublished)

Shahida Shazlin binti Saidin, Shahida Shazlin (2010) The Investigation into the Effect of Viscosity to the Friction and Wear Behaviour of Automotive Gear Oils. [Final Year Project] (Unpublished)

Shahimi, Muhammad Syamil (2013) Detection of Corrosion Under Insulation Using Infrared Thermography. [Final Year Project] (Unpublished)

Shahrom, Mohammad Firdaus (2011) Study on the Wear Resistance of Duplex Stainless Steel after Undergo Nitrogen Diffusion Process Varies With Time. [Final Year Project] (Unpublished)

Shahrul Amar, Abdul Qayyum (2016) Investigation on the Dynamic Response of a Horizontal Axis Wind Turbine with Active Blade Pitch Control. [Final Year Project] (Submitted)

Shahrul Azran Huzzeini, Shahryl Solehi Huzzeini (2022) Investigation On The Effect Of Process Parameters On Temperature Profiles Of Friction Stir Processed AA7075/SiC Composites. [Final Year Project] (Submitted)

Shakawi Efendy Jamaludin, Shakawi Efendy (2008) Study of the Use of Orifice as an Alternative for Steam Trap. [Final Year Project] (Unpublished)

Shakidi, Siti Suaidah (2017) Computational Investigation of Fluidized Drying of Paddy by Air with a State Variable of Time. [Final Year Project]

Shalini, Subramaniam (2011) Corrosion Study ofNitrided X-52 Carbon Steel in C02 Environment. [Final Year Project] (Unpublished)

Shamshuddin, Ahmad Shahizan (2011) Effect of Surface Roughness on Adhesion and Corrosion Properties for Metal Surface. [Final Year Project] (Unpublished)

Shamsud, Mohamad Hanif (2012) Design of a Desiccant Wheel of Thermally Driven Dehumidification System. [Final Year Project] (Unpublished)

Shamsuddin, Siti Nabihah (2011) Microstructural Study of Friction Stir Welded Dissimilar Materials: 6061 Aluminum Alloy to Pure Copper. [Final Year Project] (Unpublished)

Shamsuddin, Siti Nabihah (2011) Microstructural Study of Friction Stir Welded Dissimilar Materials: 6061 Aluminum Alloy to Pure Copper. [Final Year Project] (Unpublished)

Shamsudin, Mohamad Hanif (2012) Design of a Desiccant Wheel of Thermally Driven Dehumidification System. [Final Year Project] (Unpublished)

Shamsudin, Muhammad Fasha Haiqal (2016) Computational Fluid Dynamics (CFD) Study of Gas Separation Process for High Pressure Horizontal Separator. [Final Year Project] (Submitted)

Shamsudin, Nur Ain Syafiqah (2013) Infrared Thermography Inspection on Potential Failures of Rotating Equipment. [Final Year Project] (Unpublished)

Shamsudin, Nurfarahin (2011) Study on Microstructure and Strength of Friction Stir Spot Welding On Copper Alloy Sheet. [Final Year Project] (Unpublished)

Shania Ting, Ying Ying (2021) Investigation on the Effect of Nanoparticle Diameter and Concentration on the Performance of Nanofluid Solar Pond. [Final Year Project] (Submitted)

Sharuddin, Intan Naquiah (2011) Preliminary Design of Unmanned Aerial Vehicle (UA V) for Petroleum Pipe Monitoring System. [Final Year Project] (Unpublished)

Shasindran , Shanmugam (2010) Study, Design And Analysis OfH2 Gas Actuated Pneumatic Artificial Muscle Using Metal Hydride as Gas Storage Medium. [Final Year Project] (Unpublished)

Sheikh Ali, Hanif (2012) CHARACTERIZATION OF REFORMER TUBE CREEP DAMAGE BY ULTRASONIC ATTENUATION PATTERN AND MICROSTRUCTURAL CHANGES. [Final Year Project] (Unpublished)

Sheng, Caleb Ng Zhu (2016) Assessment of the Uncoated Carbide inserts in end milling of Titanium Alloy Ti-6AI-4V. [Final Year Project] (Submitted)

Sheng, Goh Ting (2016) The Effect of Using Coolant during Bone Drilling for Surgery Application. [Final Year Project] (Submitted)

Sheng, Jason Ngu Kai (2016) Preliminary Study of Renewable Pico Hydro Electrification Schemes to Improve Current Electrification Method in Royal Belum. [Final Year Project] (Submitted)

Sheng, Ong Kai (2016) PDC Bit Hydraulic and Mud Rheological Simulation to Model Pressure Drop across Bit. [Final Year Project] (Submitted)

Sherrene Crystal Anak Basil, Sherrene Crystal (2010) Fabrication of Bonded Neodymium-Iron-Boron (NdFeB) Permanent Magnet through Warm Compaction. [Final Year Project] (Unpublished)

Shirazi, Muhammad Irfan (2015) Shear Induced Fiber Orientation in Metal Injection Molded Carbon Fiber Reinforced Copper Composite. Masters thesis, Universiti Teknologi PETRONAS.

Shiun, Onn Wei (2016) INVESTIGATING THE OPTICAL LOSSES OF A SECOND REFLECTOR IN A BEAM DOWN POWER TOWER. [Final Year Project] (Submitted)

Shiun, Onn Wei (2016) INVESTIGATING THE OPTICAL LOSSES OF A SECOND REFLECTOR IN A BEAM DOWN POWER TOWER. [Final Year Project] (Submitted)

Shiva Sarvanan Pillai Subramaniam, Shiva (2012) Effects of Particle Size of Fumed Silica and Aluminium Trihydrate on Fire Performance of Intumescent Fire Retardant Coating. [Final Year Project] (Unpublished)

Sholihotdin, Syahirhatim (2011) FINITE ELEMENT ANALYSIS OF RESIDUAL STRESSES IN WELDED STRUCTURES. [Final Year Project] (Unpublished)

Shuib, Siti Suhaili (2016) Simulation Study on Combustion Characteristics of Water Tube Boiler with Different Type of Fuel. [Final Year Project] (Submitted)

Shukri, Syahrum (2014) Stress Analysis of a Defected Gear Pair Using Finite Element Analysis (FEA). [Final Year Project] (Unpublished)

Shummugham, Suntharesar (2013) VEHICLE DRIVETRAIN MODELING AND ANALYSIS FOR AN ADVANCED DRIVETRAIN OF A CITY CONCEPTCAR. [Final Year Project] (Unpublished)

Sia An An, Clare Marie (2013) DYNAMIC ANALYSIS OF A RECIPROCATING COMPRESSOR. [Final Year Project] (Unpublished)

Sidi, Sebastian anak (2009) Feasibility Study on the Replacement of Traditional Heat Exchanger by ALFA LAVAL COMP ABLOC in PETRONAS OPUs. [Final Year Project] (Unpublished)

Sim , Chieh Ying (2021) Numerical simulation and evaluation of solar chimney coupled with heat trap unit. [Final Year Project] (Submitted)

Sim Mei Sze, Deborah (2009) CFD Simulation of Multipurpose Solar Dryer. [Final Year Project] (Unpublished)

Siti Fatimah Bt Abdul Aziz, Siti Fatimah (2009) Study of Mechanical Properties of Sand Control Screens for Deepwater Applications. [Final Year Project] (Unpublished)

Siti Fatimah binti Mazalan, Siti Fatimah (2008) Comparative Study of Different CO2 Injection Modes for Baronia RV2 Reservoir. [Final Year Project] (Unpublished)

Siti Khadijah Md. Rawi, Siti Khadijah (2009) Study on the Effects of Reinforcing Chicken Feather Fiber (CFF) on Mechanical Properties of Polypropylene (PP). [Final Year Project] (Unpublished)

Siti Marhamah binti Mustafha, Siti Marhamah (2012) Design and Fabrication of Horizontal Turbine for Rural Microhydroelectric Generations. [Final Year Project] (Unpublished)

Siti Nor Fazilah Binti Abdul Basir, Siti Nor Fazilah (2010) Powder Metallurgy of Iron-based Matrix Composite with Silicon Carbide (SiC) Reinforcement. [Final Year Project] (Unpublished)

Siti Nur Farhin Mokhtar, Siti Nur (2011) FRACTURE TOUGHNESS AND FATIGUE CRACK GROWTH TESTS OF FRICTION STIR WELDED PLATES. [Final Year Project] (Unpublished)

Siti Nur Hidayah Binti Mat Salleh, Siti Nur Hidayah (2008) The Effect of Multiple-use of Polystyrene Cups on Styrene Monomer Migration. [Final Year Project] (Unpublished)

Siti Nur Jehan binti Ismail, Siti Nur Jehan (2010) Resin Infusion Strategy For Wind Turbine Blade. [Final Year Project] (Unpublished)

Siti Suhailah Binti Khairullah, Siti Suhailah (2012) PERFORMANCE MEASURE FOR STEAM ABSORPTION CHILLER OF A DISTRICT COOLING PLANT. [Final Year Project] (Unpublished)

Sitoi, Helder (2012) Solar adsorption cooling system using activated media for equatorial humid climate. [Final Year Project] (Unpublished)

Siva Sankara Arudra, Siva (2010) Study Of Corrosion And Engine Performance Characteristics Of Emulsified Diesel. [Final Year Project] (Unpublished)

Sivanathan, Prema (2019) Effect of Chloride Concentrations and Temperature On Pre-Stressed Austenitic Stainless Steel 304 Based on Pressure Vessel in Oil and Gas Industry. Masters thesis, Universiti Teknologi PETRONAS.

Sivaraj, Ramaneish (2020) To study the Hardness and Mechanical Properties of Aluminium Composite Reinforced with Titanium Carbide & Graphite. [Final Year Project] (Submitted)

Software Abaqus 6.15. [Teaching Resource] (Submitted)

Software Autodesk AutoCAD 2012 Education. [Teaching Resource] (Submitted)

Software Catia V5-6R2012. [Teaching Resource] (Submitted)

Software GT Power ver 6.2. [Teaching Resource] (Submitted)

Software GT Power ver 6.2. [Teaching Resource] (Submitted)

Software JMP 10 Statistical Discovery Software. [Teaching Resource] (Submitted)

Software JMP Software. [Teaching Resource] (Submitted)

Software MSC Adam 2015. [Teaching Resource] (Submitted)

Software ReliaSoft Weibull++ and Blocksim. [Teaching Resource] (Submitted)

Software Solidworks / SimpoeWorks 2012. [Teaching Resource] (Submitted)

Software Solidworks / SimpoeWorks 2014. [Teaching Resource] (Submitted)

Software TRNSYS Version 17. [Teaching Resource] (Submitted)

Software Witness 12. [Teaching Resource] (Submitted)

Sofuan Najen Bin Othman, Sofuan Najen Bin Othman (2012) Modeling of Spur Gear Meshing Characteristics under Various Crack Size. [Final Year Project] (Unpublished)

Soon, Kee Lian (2011) Experimental Study of Oil Palm Biomass Waste Mixture for Energy Potential. [Final Year Project] (Unpublished)

Soraya Abd Rahman, Soraya (2008) A Study on Co-firing Empty Fruit Bunch (EFB) with Coal as Potential Fuel. [Final Year Project] (Unpublished)

Sridaran Nair, Wamadevan Nair (2021) Remaining Strength Estimation For AISI 1020 Carbon Steel Pipeline Internal Corrosion Using Finite Element Analysis. [Final Year Project] (Submitted)

Su Rat, Santie Chai Khamkeo (2020) Computer Simulation Development of Hydro-cyclone Performance in Solid Liquid Separation. [Final Year Project] (Submitted)

Subramaniam, Ramesh (2016) Experimental Study of Paraffin Wax Precipitation and Its Effect on Corrosion Behavior of Carbon Steel Pipeline. [Final Year Project] (Submitted)

Sufian Hardi Bin Yusof, Sufian Hardi (2008) Failure Analysis on Water Heater Tube. [Final Year Project] (Unpublished)

Suhaimi, Noorazreen (2010) Comparison of Performance between Centrifugal and Positive Displacement Pump at Low Flow Rate. [Final Year Project] (Unpublished)

Suhaimi, Nor Ernie Akmal (2008) Characterization of Local Sands for Possible Use as Proppant. [Final Year Project] (Unpublished)

Suhaimi Bin Shazali, Suhaimi (2009) Failure Analysis on the Wire Rope for Lifting Equipment. [Final Year Project] (Unpublished)

Suhardi, Muhammad Safiq Safwan Hady (2017) Investigation of Titanium Dioxide Reinforcement on Thermal Performance of Siloxane Epoxy Based Intumescent Fire-Retardant Coating Systems. [Final Year Project] (Submitted)

Suhazeli, Abdul Munir (2022) Analysis On The Performance Of Vibration Energy Harvester. [Final Year Project] (Submitted)

Sukur, Mohammad Ariff (2008) Mechanical and Microstructural Characterization of Hybrid Composite Developed By Compression Molding. [Final Year Project] (Unpublished)

Sulaiman, Fahim Anati (2011) Seabed Logging Modeling Using Comsol Multiphysic Software: Effect of Hydrocarbon Geometry to the EM Wave. [Final Year Project] (Unpublished)

Sulaiman, Mohamad Rozi (2011) PERFORMANCE EVALUATION MODELING OF PRE-TREATMENT UNIT IN GAS PROCESSING PLANT. [Final Year Project] (Unpublished)

Sulaiman, Mohammad Syafiq (2017) Development of Framework for Data and Evidence Collection in Root Cause Analysis for Petrochemical Plant. [Final Year Project]

Sulaiman, Mohd Amirul Hakim (2008) BANANA TRUNK AS A LOST CIRCULATION MATERIAL IN HYDROCARBON DRILLING FLUID. [Final Year Project] (Unpublished)

Sulaiman, Nor Hidayatul Solehah (2011) Thermodynamic Analysis and Comparison of CO2/Propane and C02/Isobutane Cascade Refrigeration System. [Final Year Project] (Unpublished)

Sulaiman, Shafiq (2011) Waste Management In Petroleum Refinery Spent Catalyst. [Final Year Project] (Unpublished)

Sundraj, Suthan Aravinthan (2009) Research and Analysis of a Micro EDM System. [Final Year Project] (Unpublished)

Sunif, Muhammad Amri Bahri (2015) Investigation of Friction Stir Welding Tool Wear on Different Hardening Method. [Final Year Project] (Unpublished)

Suresh Naidu, Shaarvin Naidu (2021) Fire Hazard Risk Assessment Due to Domino Effect in Petroleum Plant. [Final Year Project] (Submitted)

Suriawani Bt Sulaiman, Suriawani (2008) Design of intake cooling system for Taurus 60 Gas Turbine Generator in UTP Gas District Cooling Plant using chilled water supply. [Final Year Project] (Unpublished)

Suriawani Sulaiman, Suriawani (2008) Design of intake cooling system for Taurus 60 Gas Turbine Generator in UTP Gas District Cooling Plant using chilled water supply. [Final Year Project] (Unpublished)

Syafri bin Mohd Yunus, Syafri (2008) Improvement of Oil and Water Separation in Three-Phase Conventional Separator Using Hydrocyclone Inlet Device. [Final Year Project] (Unpublished)

Syahidatulmazidah binti Ismail, Syahidatulmazidah (2008) Magnetic Properties and Corrosion Study on Bonded NdFeB Magnet Using Wet and Dry Binders. [Final Year Project] (Unpublished)

Syahril, Zuhair Amin (2021) Study of Erosion Formation on M152 Steel Alloy due to Impact Angle. [Final Year Project] (Submitted)

Syahril Izzat Bin Azmi, Syahril Izzat (2010) Drive mechanism for Personal Transporter (PT). [Final Year Project] (Unpublished)

SyahrulEhwan Bin Lamat, SyahrulEhwan (2010) Studies and Simulation of Five Link Suspension Systems. [Final Year Project] (Unpublished)

Syaida Hazira Binti Ramli, Syaida (2011) CFD SIMULATIONS OF ANNULAR DISTRIBUTOR OF SWIRLING FLUIDIZED BED (SFB) REACTOR. [Final Year Project] (Unpublished)

Syarizatul Nadia binti. Rosdi, Syarizatul (2008) Application of Solar Energy in Drying Pepper. [Final Year Project] (Unpublished)

Syed Ahmad Alhabshi, Syed Naufal (2012) Thermal Distribution of Temperature Rise for 18V Cordless Impact Drill. [Final Year Project] (Unpublished)

Syed Muhammad Afiq Bin Syed Othman, Syed Muhammad (2012) DESIGN OF MECHATRONIC SYSTEM FOR EYEBALL MOVEMENT. [Final Year Project] (Unpublished)

Syed Sheikh, Syed Sadiq (2011) A STUDY OF ACETIC ACID ROLE IN C02 CORROSION. [Final Year Project] (Unpublished)

Syukri, Muhamad Safuan (2015) Thermal Simulation of Different Welding Speed and Metal Thickness for Butt-Joint Welding with ANSYS. [Final Year Project] (Unpublished)

T

TAJUL ARIFFIN, MOHD ARIF (2017) CHLORIDE STRESS CORROSION CRACKING FOR 304L AUSTENITIC STAINLESS STEEL. [Final Year Project] (Submitted)

TAN, FOK HON (2011) SIMULATION OF ENERGY PROMOTERS IN THE INTERMEDIATE PASSAGE OF GAS TURBINE. [Final Year Project] (Unpublished)

TAN , YINN HOONG (2008) A STUDY OF MECHANICAL ROBUSTNESS OF PORTABLE ELECTRONIC DEVICE SUBJECTED TO MECHANICAL DROP. [Final Year Project] (Unpublished)

TARIQ, ADEEL (2020) NUMERICAL AND EXPERIMENTAL ANALYSIS OF THERMAL AND HYDRAULIC PERFORMANCE OF PERFORATED AND SLOTTED PLATE-FIN HEATSINKS. Masters thesis, Universiti Teknologi PETRONAS.

TAT, HON LIAN (2017) CFD Simulation of Two-phase Slug Flow Liquid Carryover in T-junction Corresponds to Various Diameter Ratio. [Final Year Project]

TAUFIQURRAHMAN, IQBAL (2021) THE STUDY ON THE RESISTANCE SPOT WELDING OF DISSIMILAR MATERIALS OF STAINLESS STEEL 316L AND TI-6AL-4V TITANIUM ALLOY WITH THE INTERLAYER OF ALUMINUM ALLOY. Masters thesis, Universiti Teknologi PETRONAS.

TAWFEIG AHMED IZZELDIN, HUZAIFA (2009) PREDICTING FLOW RATE AND LEVEL OF CUSTOM TANK USING PARTICLE FILTER. [Final Year Project] (Unpublished)

TENGKU MUHAMMAD, TENGKU IBRAHIM (2011) Reliability Block Diagram Method for RAM Study of Dehydration Unit. [Final Year Project] (Unpublished)

TERRY, DARYL LUKE (2017) VEHICLE DYNAMICS MODELING AND SIMULATION OF A 110 C.C. MOTORCYCLE DURING CORNERING. [Final Year Project]

TG. ALI, TENGKU MOHAMAD AMIRUL (2018) Effect of Nitriding Temperature and Nitriding Time On Magnesium, MgAZ91D Alloy. [Final Year Project] (Submitted)

THAW , ZIN HTUN (2017) A CORROSION STUDY OF PINHOLE COATING DEFECTS IN CARBON DIOXIDE ENVIRONMENT. [Final Year Project]

TRAN, NGO NGUYET (2018) NUMERICAL SIMULATIONS OF EROSION IN 90-DEGREE ELBOW DUE TO FINE PARTICLES TRANSPORTED IN ANNULAR FLOW REGIME. Masters thesis, Universiti Teknologi PETRONAS.

Taha Ellakany, Farid Fawzy Fathy (2011) Preliminary Drying of Oil Palm Fronds Using Concentrated Solar Thermal Power. [Final Year Project] (Unpublished)

Tajuddin, Noraiman (2015) Design, Construction and Experimental Analysis of Free Floating Pig for Pipeline Leak Detection. [Final Year Project] (Unpublished)

Tajul Syazwan Bin Tajor Amar, Tajul Syazwan (2011) Scheduling of Electricity Distribution at UTP GDC Plant Using Linear Programming. [Final Year Project] (Unpublished)

Talipov, Rustam (2013) ANALYTIC HIERARCHY PROCESS APPROACH FOR SELECTION AND EVALUATION OF MAINTENANCE STRATEGY. [Final Year Project] (Unpublished)

Tan, Kien Weng (2009) Simulation And Flow Characterization Of Spiked Supersonic Gas Turbine Intake At Non-Zero Angle Of Attack. [Final Year Project] (Unpublished)

Tan, Ming Chai (2004) High Viscous Fluid Transport Model. [Final Year Project] (Unpublished)

Tan, Tai Keong (2021) Performance Analysis of a Novel Nanofluid Assisted Thermoelectric Air Conditioner for Energy Efficient Building. [Final Year Project] (Submitted)

Tan , Jason Min Chuan (2008) Evaluation and Modelling Residual Stress of a Joining - Sialon to Austenitic Stainless Steel. [Final Year Project] (Unpublished)

Tan , Kwong Hoe (2010) Vehicle Ride Investigation Of Myvi With Adams Car. [Final Year Project] (Unpublished)

Tan , Min Chuan, Jason (2008) Evaluations and Modelling of Residual Stress of a joining- Sialon to Austenitic Stainless Steel. [Final Year Project] (Unpublished)

Tan , Yinn Hoong (2008) A Study of Mechanical Robustness of Portable Electronic Device Subjected to Mechanical Drop. [Final Year Project] (Unpublished)

Tan Boon Tat, Boon Tat (2010) Determination Of Heat Transfer Coefficients In Heat Exchangers By Genetic Algorithm. [Final Year Project] (Unpublished)

Tan Kwong Hoe, Kwong (2010) Vehicle Ride Investigation Of Myvi With Adams Car. [Final Year Project] (Unpublished)

Tan Yusoff, Tuan Mohd Faizie (2010) The Influence of Filler Loading on Mechanical Properties of Rice Husk Reinforced High Density Polyethylene. [Final Year Project] (Unpublished)

Taufi Qil Hafiz Bin Mohd Tahar, Taufi Qil Hafiz (2008) Modelling and Analysis of a Car Bumper. [Final Year Project] (Unpublished)

Teh, Choon Chi (2008) Study on Characterisation and Property of Local Sand. [Final Year Project] (Unpublished)

Tengku, Hillary (2022) Residual Strength Estimation of Medium Toughness Pipe Elbows with Longitudinally Aligned Interacting Corrosion Defects Subjected to Internal Pressure. [Final Year Project] (Submitted)

Tengku Ibrahim bin Tengku Muhammad, Tengku Ibrahim (2011) Reliability Block Diagram Method for RAM Study of Dehydration Unit. [Final Year Project] (Unpublished)

Tengku Norhanisah Bt Tengku Kamaruddin, Tengku Norhanisah (2011) Experimental Study on Gas Turbine Engine Dynamics. [Final Year Project] (Unpublished)

Tengku Shahril Nizam Bin Tengku Mohd Yusof, Tengku Shahril Nizam (2010) Effect of a Moving Load to A Jetty Gangway. [Final Year Project] (Unpublished)

Teoh , Chia Yang (2014) Reverse Engineering for Measuring Skin Ulcer Size with 3D Scanning. [Final Year Project] (Unpublished)

Thamil Selvan, Sritharan (2021) Real Time Flow Assurance Diagnostic Using Data Analytics. [Final Year Project] (Submitted)

Thamotharan, Naaventhiran (2021) Study on The Mechanical Properties of Aluminium Wire Made from Friction Extrusion Process. [Final Year Project] (Submitted)

Thaweesak Hemchi, Thaweesak (2008) Thermal stress and Thermal expansion in a brake drum of heavy commercial truck. [Final Year Project] (Unpublished)

Thayyibah Jamalullail, Thayyibah (2010) Evaluation of Flat Plate Enhanced with Phase Change Material PCM. [Final Year Project] (Unpublished)

Thembinkosi Robert Khumalo, Robert Khumalo (2008) Analytical and CFD Simulation of an on-roof Wind Generator Using Biomass. [Final Year Project] (Unpublished)

Thomas Martin, Diana Lia (2016) Process Improvement in Healthcare through the Application of Lean Concepts. [Final Year Project] (Submitted)

Tian Hui, Chan (2017) Degradation of Polymers in the Presence of Sulfate Reducing Bacteria Microbes. [Final Year Project]

Toh, Seng Peow (2011) Analytical and Experimental Investigation of Convective Heat Transfer in Solar Collector. [Final Year Project] (Unpublished)

Toh , Jia Lin (2010) Design, Fabrication And Test Of Variable Height Solar Chimney. [Final Year Project] (Unpublished)

Tony, Charles Runyaam (2021) Prototyping and Piloting the Flexi Hose for Onshore and Offshore Pipeline Rehabilitation. [Final Year Project] (Submitted)

Torng, Hea Yih (2016) On-Bottom Stability Study of Non-Metallic Pipeline Due To Hydrodynamic Loadings. [Final Year Project] (Submitted)

Tuan Mohd Faizie Bin Tan Yusoff, Tuan Mohd Faizie (2010) The Influence of Filler Loading On Mechanical Properties of Rice Husk Reinforced High Density Polyethylene. [Final Year Project] (Unpublished)

Tuan Nur Aiman Bin Tuan Kamaruddin, Tuan Nur Aiman (2008) Investigation of the Effect of Exhaust Middle Pipe Length to the Engine Performance. [Final Year Project] (Unpublished)

Tze-Shyuen, Leroy Wong (2014) Computational Fluid Dynamics Study of Flow within a Double Gap Cylinder. [Final Year Project] (Unpublished)

U

UL MUSTAFA, MUHAMMAD ZIA (2015) SYNERGISTIC EFFECTS OF SILICATE MINERAL FILLERS REINFORCED INTUMESCENT FIRE RETARDANT COATING FOR STRUCTURAL APPLICATIONS. Masters thesis, Universiti Teknologi PETRONAS.

ULLAH, BARKAT (2019) DESIGN AND MOTION CONTROL OF AN UNDERWATER GLIDER IN THE PRESENCE OF WAVE AND CURRENT DISTURBANCES. PhD. thesis, Universiti Teknologi PETRONAS.

UMAR ALKALI, ADAM (2015) INVESTIGATION OF THERMALLY ENHANCED MACHINING ON MACHINABILITY OF 316L STAINLESS STEEL USING OXYACETYLENE FLAME AS HEAT SOURCE. PhD. thesis, Universiti Teknologi PETRONAS.

Ummu Hani Ilias, Ummu (2011) Effect of Different Welding Tool Pin Shapes on Friction Stir Welding Plates Microstructure. [Final Year Project] (Unpublished)

V

V.Jagendran Naidu A/L Veerannan, V.Jagendran Naidu (2011) An investigation on the energy recovery potential of sewage sludge in Malaysia through biogas generation. [Final Year Project] (Unpublished)

VEERANNAN, V.JAGENDRAN NAIDU (2011) An investigation on the energy recovery potential of sewage sludge in Malaysia through biogas generation. [Final Year Project] (Unpublished)

VEERENDRA, CHITTURI (2021) INVESTIGATION ON WELDABILITY OF DISSIMILAR FRICTION STIR WELDED AA5052 AND SS304 ALLOYS. Doctoral thesis, UNSPECIFIED.

VENKITESWARAN, VINOD KUMAR (2013) HYDRODYNAMICS OF SWIRLING FLUIDIZED BED. PhD. thesis, UTP.

VENKITESWARAN, VINOD KUMAR (2014) STUDY OF HYDRODYNAMIC PROPERTIES OF SWIRLING FLUIDIZED BED. PhD. thesis, Universiti Teknologi PETRONAS.

VIN, TAN AL (2017) Investigation of Effectiveness of Statistical Methods to Gas Turbine Vibration Diagnostics and Synthesis of SVM Based Approach. [Final Year Project]

Varatharajoo, Hashmentd Rajah (2022) Modelling And Simulation of A Series-Parallel Hybrid Propulsion System For A Fixed Wing Quadcopter. [Final Year Project] (Submitted)

Veejendran, Shesathri Ram (2021) Development and Characterization of Laser Scribed Polyimide Graphene Electrochemical Supercapacitor Electrodes with Different Substrates. [Final Year Project] (Submitted)

Vern, Kong Kai (2015) Effect of Size and Shape of PDC Cutter on Wear Rate in Multi Layer Formation. [Final Year Project] (Unpublished)

Vijaya Kumar, Sathia Devi (2022) Residual Strength Prediction of Medium Toughness Pipe Elbow with Circumferentially Aligned Interacting Corrosion Defects Subjected to Internal Pressure. [Final Year Project] (Submitted)

Vinod A/L Chandra Sayakaran, Vinod (2010) A Study on the Stiffness of Solid And Hollow Section Brass. [Final Year Project] (Unpublished)

Vong, Winnie Chin Joo (2005) Development of Knowledge Based Welding Inspection Data and Generate Report Format According to Standard Code. [Final Year Project] (Unpublished)

W

W. Zakaria, W. Nur Liyana (2014) The Effect of Enhanced Oil Recovery (EOR) Surfactant on Pipeline Corrosion in CO2 Environment. [Final Year Project] (Unpublished)

WAN ABD AZIZ, WAN AHMAD AMMAR (2014) CFD Simulation of Reactor Bed for Adsorbed Natural Gas Storage System. [Final Year Project] (Unpublished)

WASIU, KAREEM MORAKINYO (2017) MATHEMATICAL MODELLING AND EXPERIMENTAL INVESTIGATION OF MULTI-PASS SOLAR AIR HEATING COLLECTOR SYSTEM ASSISTED BY POROUS MATRIX. PhD. thesis, Universiti Teknologi PETRONAS.

WASIU BABATUNDE, AYANDOTUN (2013) THE EFFECT OF CARBON DIOXIDE (C02) CONTENTNATURAL GAS ON THE PERFORMANCE CHARACTERISTICS OF A DIRECT INJECTION (DI) COMPRESSED NATURAL GAS (CNG) ENGINE. Masters thesis, UTP.

WASSAN, MAJID ALI (2014) A STUDY ON LIQUID DESICCANT SYSTEM FOR THE DEVELOPMENT OF DEHUMIDIFIER'S/REGENERATOR'S MATHEMATICAL MODEL. Masters thesis, Universiti Teknologi PETRONAS.

WASSAN, RANO KHAN (2014) SEMI-QUANTITATIVE RISK ASSESSMENT MODEL FOR ROTATING EQUIPMENT. Masters thesis, Universiti Teknologi PETRONAS.

WONG, WAI KIT (2009) PREDICTING THE RELIABILITY OF A REPAIRABLE SYSTEM WITH COMPETING FAILURE MODES. [Final Year Project] (Unpublished)

WONG , CHEE KING (2013) Studies on a Two-layer Swirling Fluidized Bed (SFB). [Final Year Project] (Unpublished)

WOO , TZE KEONG (2016) DEVELOPMENT AND ANALYSIS OF HIGH SPEED DRILLING INDUCED DELAMINATION IN GLASS FIBER REINFORCED POLYMER. PhD. thesis, Universiti Teknologi PETRONAS.

Wahi, Nur E’zzati (2013) Study on Combustions Characteristics of Diesel-Vegetable Oil Blended using Industrial Fuel Burner. [Final Year Project] (Unpublished)

Wahid, Abdul Hakim (2018) Leak Detection in Liquid Pipeline using Flow Monitoring Method. [Final Year Project] (Submitted)

Wan Ahmad Fahmi Azrin Che Mohd, Wan Ahmad Fahmi Azrin (2011) GEOPOLYMER CEMENT FOR OIL WELL WITH IMPROVED PROPERTIES. [Final Year Project] (Unpublished)

Wan Ahmad Fuad Ali bin Wan Abd Ghafar, Wan Ahmad Fuad Ali (2008) Comparison of Methods to Reduce Grid Orientation Effect in Miscible Flood Simulation. [Final Year Project] (Unpublished)

Wan Amalina Wan Zaharuddin, Wan Amalina (2008) Study on the Integrity of the Intumescent Bonding to the Steel Substrate before Fire Exposure. [Final Year Project] (Unpublished)

Wan Amat, Wan Norizan (2010) ANALYSIS OF BOILER TUBE LEAKAGE BY USING ARTIFICIAL NEURAL NETWORK. [Final Year Project] (Unpublished)

Wan Amirudin bin Wan Mohamad Noor, Wan Amirudin (2009) Design and Analysis of a Small Formula-Style Race Car Suspension System. [Final Year Project] (Unpublished)

Wan Azaha, Wan Nor Suhaina (2018) Effect of Nitriding Temperature and Time with Gas Mixture of 95% Nitrogen and 5% Hydrogen on MgAZ91D Alloy. [Final Year Project] (Submitted)

Wan Basiron, Wan Amirul Asyraf (2020) Performance Investigation of Flat Plate Solar Collector using vegetable oil-based nanofluids. [Final Year Project] (Submitted)

Wan Faradinah binti Zainal Abidin, Wan Faradinah (2010) Performance Evaluation Of Thermal Energy Storage For District Cooling Plant. [Final Year Project] (Unpublished)

Wan Ghazali, Wan Nor Maawa (2009) Design and Analysis of a Pedal Box System for FSAE 2010. [Final Year Project] (Unpublished)

Wan Ibrahim, Wan Mohd Syazwan (2008) RELIABIUTY PREDICTION AND MODELING: A Case Study ofDry Gas Seal and Buffer Gas System on Compressor for Gas Transportation. [Final Year Project] (Unpublished)

Wan Ibrahim Bin Wan Mamat, Wan Ibrahim (2012) Development in Synthesis of Silicon Carbide from Natural Resource. [Final Year Project] (Unpublished)

Wan Ismail, Che Wan Mohd Hafizul Azizi (2008) Design and Analysis of a Drive Train System for a Small Race Car. [Final Year Project] (Unpublished)

Wan Izzul Fathi Bin Hamdan, Wan Izzul Fathi (2012) Investigate the Thermal Effects on Flow Resisting Properties of Hydrocarbons in a Pipeline [EXPERIMENT]. [Final Year Project] (Unpublished)

Wan Jusoh, Wan Nursheila (2005) Sintered Bonding ofthe M3/II High Speed Steel and Cast Iron. Masters thesis, Universiti Teknologi PETRONAS.

Wan Khairul Anuar, Wan Ahmad Ridhwan (2011) Design and Analysis of a Multi-Purpose Small Personal Transport System with In-Wheel Drive System. [Final Year Project] (Unpublished)

Wan Mazlan, Wan Mohd Safwan (2008) Development of an External Laptop Cooler with Thermoelectric Device. [Final Year Project] (Unpublished)

Wan Mohd Aizuddin Bin Wan Doshah, Wan Mohd Aizuddin (2009) Development of Sway Angle Measurement System. [Final Year Project] (Unpublished)

Wan Mohd Hariri B. Mohd Nasihuddin, Wan Mohd Hariri (2009) Pre-design Latent Heat Thermal Energy Storage using Energy from Electricity Grid. [Final Year Project] (Unpublished)

Wan Mohd Noh, Wan Najlin (2013) Surface Roughness of Stainless Steel by Micro-Milling for Biomedical Applications. [Final Year Project] (Unpublished)

Wan Mohd Safwan Bin Wan Mazlan, Wan Mohd Safwan (2006) Development of an External Laptop Cooler with Thermoelectric Device. [Final Year Project] (Unpublished)

Wan Mohd Syazwan Bin Wan Ibrahim, Wan Mohd Syazwan (2008) Reliability Prediction And Modeling: A Case Study Of Dry Gas Seal And Buffer Gas System On Compressor For Gas Transportation. [Final Year Project] (Unpublished)

Wan Mohd Syazwan Bin Wan Ibrahim, Wan Mohd Syazwan (2008) Reliability Prediction And Modeling: A Case Study Of Dry Gas Seal And Buffer Gas System On Compressor For Gas Transportation. [Final Year Project] (Unpublished)

Wan Nadhari, Wan Noor Azleen (2016) Mechanical Properties of “Mengkuang” Fibre Reinforced Composite. [Final Year Project] (Submitted)

Wan Norizan B Wan Amat, Wan Norizan (2010) Analysis Of Boiler Tube Leakage Using Artificial Neural Network. [Final Year Project] (Unpublished)

Wan Normimi Roslini Binti Abdullah, Wan Normimi Roslini (2009) Study on Corrosion Inhibitor Efficiency for Carbon Steel in CO2 Corrosion. [Final Year Project] (Unpublished)

Wan Rahim, Wan Abdul Azeem (2016) Real Time Algorithm of Wear Detection. [Final Year Project] (Submitted)

Wan Rahim, Wan Abdul Halim (2004) Computer Program Development To Analyse Centrifugal Compressor Performance. [Final Year Project] (Unpublished)

Wan Rozuhan, Wan Nur Hamizah (2017) Conversion of Rice Husk into Amorphous Silicon Dioxide Using Taguchi’s Method. [Final Year Project] (Submitted)

Wan Sohaimi, Wan Muhammad Faris (2012) EVALUATION OF COATING PERFORMANCE FOR CORROSION UNDER INSULATION (CUI) PREVENTION. [Final Year Project] (Unpublished)

Wan Suhaimi, Wan Irfan Hafez (2021) Convective Heat Transfer of Nanofluids in Helical Tube with Twisted Tape Insert. [Final Year Project] (Submitted)

Wasiu, Kareem Morakinyu (2017) Mathematical Modelling and Experimental Investigation of Multi-Pass Solar Air Heating Collector System Assisted by Porous Matrix. Doctoral thesis, Universiti Teknologi PETRONAS.

Wee, Kelvin Ting (2015) 3D Reconstruction Using Light Field Camera. [Final Year Project] (Unpublished)

Wei, Wong Hoong (2016) Setting Up a Remote Accessing of a PV Plant and Its Analysis. [Final Year Project] (Submitted)

Wei Ren, Ivan Gan (2016) Numerical Simulation of Extreme Wave Loading on Deep-water SPAR Platforms using the SPH Method. [Final Year Project] (Submitted)

Wei Wen, Jeremy Lo (2013) PROPOSAL FOR EFFICIENT METHODS TO PRODUCE CURVED PISTON FOR MASS PRODUCTION. [Final Year Project] (Unpublished)

Wendimu Fanta Gemechu, Wendimu (2010) The Design of Automated Control System for Wastewater Treatment Plant. [Final Year Project] (Unpublished)

Woldeyohannes, Abraham Debebe (2010) Simulation Model for the Analysis of Pipeline Network System with Non-pipe Elements for Natural Gas Transmission. PhD. thesis, Universiti Teknologi PETRONAS.

Wolian, Duku Paul (2016) Characterization and Properties of Powder Metallurgy Alumina-Copper Ceramic Composites. [Final Year Project] (Submitted)

Wong, Chen Hau (2022) Simulation of Data Centre Cooling using Altaire. [Final Year Project] (Submitted)

Wong , Chung Hoong (2008) Study of Drop Impact Resistance on Fiber Reinforced Composite Plates. [Final Year Project] (Unpublished)

Wong , Peck Koon (2009) Micro Aerial Vehicle (MAV): An Aerodynamics Optimized Design. [Final Year Project] (Unpublished)

Wong , Wai Kit (2009) Predicting The Reliability Of A Repairable System With Competing Failure Modes. [Final Year Project] (Unpublished)

Wong Ning, Wong Ning (2012) Characterizing the Paraffinic Composition in Malaysian Crudes. [Final Year Project] (Unpublished)

Woo, Tze Keong (2016) Develepment and Analysis of High Speed Drilling Induced Delamination in Woven Glass Epoxy Composites. Doctoral thesis, Universiti Teknologi PETRONAS.

X

Xi Yi, Chin (2010) Applieation of Swirling fluidized bed in Converting Bio oil to Gasoline. [Final Year Project] (Unpublished)

Y

Y ahaya, Mohd Roziee (2008) Effect of Used Engine Oil to High Strength Microwave Incinerated Rice Husk Ash (MIRRA) Concrete. [Final Year Project] (Unpublished)

YAHAYA, AHMAD WAFIY ADLI (2017) CHARACTERIZATION OF ZINC OXIDE AS DIELECTRIC CERAMICS FOR REDUCTION OF INTERFACIAL TENSION BETWEEN OIL AND WATER. [Final Year Project] (Submitted)

YAHYA, MOHD FARHAN (2009) Design and Development of a Vacuum Chamber for Resin Infusion Process. [Final Year Project] (Unpublished)

YAHYAZADEH, AMIN (2017) COST MINIMIZATION MODEL FOR GAS DISTRIBUTION NETWORK BY USING LINEAR PROGRAMMING METHOD. Masters thesis, Universiti Teknologi PETRONAS.

YAMIN, MOHD FADILLAH (2021) MECHANICAL AND MICROSTRUCTURE PROPERTIES EVALUATION OF SIMILAR THIN AA7075-T6 WELDS BY REFILL FRICTION STIR SPOT WELDING. Masters thesis, Universiti Teknologi PETRONAS.

YAO, HOR WENG (2015) Assessment of Imperfect Heater Contact due to in-situ Pyrolysis of Oil Shale. [Final Year Project] (Unpublished)

YAO, MOK WEN (2017) PERFORMANCE INVESTIGATION OF DESICCANT SYSTEM FOR DEHUMIDIFICATION OF TOPICAL AIR. [Final Year Project]

YASIN, FARAH QURSIAH (2011) Study of Suspended Droplets by Laser Attenuation Method. [Final Year Project] (Unpublished)

YASIR, MUHAMMAD (2020) THERMO-MECHANICAL PROPERTIES OF BASALT AND GLASS FIBER REINFORCED INTUMESCENT FIRE RETARDANT COATING FOR STRUCTURAL STEEL APPLICATION. PhD. thesis, Universiti Teknologi PETRONAS.

YAU, KAR HING (2014) EXPERIMENTAL AND NUMERICAL STUDIES ON THE THERMAL CONI ACT RESISTANCE OF A FIN TUBE HEAT EXCHANGER. PhD. thesis, Universiti Teknologi PETRONAS.

YAZID, EDWAR (2015) SLOW DRIFT MOTIONS IDENTIFICATION OF FLOATING STRUCTURES USING TIME-VARYING INPUT -OUTPUT MODELS. PhD. thesis, Universiti Teknologi PETRONAS.

YEE , YUAN BIN (2009) Design of Control System for Quadruped Robot (4-Legged Robot). [Final Year Project] (Unpublished)

YONG , HONG YAW (2018) HYDRODYNAMIC STUDY OF FREE STANDING DRILLING RISERS UNDER HURRICANE CONDITIONS. Masters thesis, Universiti Teknologi PETRONAS.

YOONG, DESMOND LIM CHIN (2017) COMPUTER SIMULATION AND ENERGY ANALYSIS OF LOW ENERGY OFFICE ROOM THROUGH UTILIZING PHASE CHANGE MATERIAL-COUPLED HEAT EXCHANGER. [Final Year Project]

YOUSIF ABDALLA, ABDULRAHMAN (2015) NEWTONIAN AND NON-NEWTONIAN FLOW IN STRAIGHT AND CURVED PIPES. Masters thesis, Universiti Teknologi PETRONAS.

YOUSIF IBRAHIM, ALAELDEEN ALTAG (2015) THE EFFECT OF C:H RATIO OF FUEL IN CENTRALLY IGNITED LAMINAR FLAME. PhD. thesis, Universiti Teknologi PETRONAS.

YUAN, SHU SHIK (2017) MIXING DYNAMICS OF STRATIFIED VORTEX PAST TILTED PIPELINE. [Final Year Project]

Yaacob, Nor Hayati (2005) Dynamic Modeling And Open-Loop Control Of A Twin Rotor Mimo System/ by Nor Hayati Yaacob, TJ 213 .N822 2005. [Final Year Project]

Yaakub, Syamilah (2015) Analysis on Effect of Wheel Size in PEV Performance. [Final Year Project] (Unpublished)

Yaccob, Mohd Syazwan Akmal (2009) Experimental studies on strength of friction stir spot welding (FSSW). [Final Year Project] (Unpublished)

Yahaya, Hasnul Radzi (2004) Design and Fabrication of a Fuselage for a Remote-Controlled Electric-Powered Airborne Imagery Platform. [Final Year Project] (Unpublished)

Yahaya, Mohd Afzal Syahin (2016) Mechanical Properties and Corrosion Resistance of Nitrided Austenitic Stainless Steel (ASS) 316L at Low Temperature. [Final Year Project] (Submitted)

Yahaya, Muhammad Syazwan Azrie (2013) Microstructure and Hardness Investigation of Different Welding Passes in Weld Zones. [Final Year Project] (Unpublished)

Yahaya, Muhammad Syazwan Azrie (2013) Microstructure and Hardness Investigation of Different Welding Passes in Weld Zones. [Final Year Project] (Unpublished)

Yahaya, Saiful Zareek (2004) Intelligent Pig Launcher. [Final Year Project] (Unpublished)

Yang, Chong Yew (2016) Texture Surface Analysis of Hydrodynamic Journal Bearing. [Final Year Project] (Submitted)

Yang, Xiong Liang (2021) FABRICATION AND CHARACTERIZATION OF AL7075-TITANIUM CARBIDE/GRAPHITE COMPOSITES FOR ENCHANCED MECHANICAL PROPERTIES USING FSP. [Final Year Project] (Submitted)

Yap, Hong Yi (2021) Study of Solid Particles Properties In Influencing Erosion of Gas Turbine Using Computational Fluid Dynamics. [Final Year Project] (Submitted)

Yap, Pun Chee (2010) Corrosion Prediction Model Of Corroded Pipeline Using Gumbel. [Final Year Project] (Unpublished)

Yasaa, Dzul Khairee (2011) Study on Effects of Nanosilica Sand Addition on Physical and Mechanical Properties of Polypropylene (PP). [Final Year Project] (Unpublished)

Yasmin Binti Mohd. Azmi, Yasmin (2010) Study the Effects of Carbon Nanotube and Expandable Graphite On The Performance Of Intumescent Fire Retardant Coating. [Final Year Project] (Unpublished)

Yau Kin, Lau (2013) Energy Conservation in Buildings. [Final Year Project] (Unpublished)

Yaw, Yong Hong (2016) Single Phase Turbulent Flow Regime Characterization Using Image Processing Techniques. [Final Year Project] (Submitted)

Yazib, Muhammad Muaz (2020) Contribution of Zinc Oxide and Halloysite Nanotubes in Epoxy Coating for Corrosion Protection. [Final Year Project] (Submitted)

Yee, Yuan Bin (2009) Design of Control System for Quadruped Robot (4-Legged Robot). [Final Year Project] (Unpublished)

Yee , Guo Shen (2020) Numerical Study on Cross Flow Maisotsenko Cycle Indirect Evaporative Cooling (MCIEC) Heat Exchanger. [Final Year Project] (Submitted)

Yee , Yuan Bin (2009) Design of Control System for Quadruped Robot (4-Legged Robot). [Final Year Project] (Unpublished)

Yegarajoo, Seridheren (2016) Design Smart In-Field Liner Hose IFL for Offshore Petroleum Pipeline Rehabilitation. [Final Year Project] (Submitted)

Yew , Jia-Wei (2016) EXPERIMENTAL AND NUMERICAL INVESTIGATION OF THE TOP PLATE INFLUENCE ON THE PERFORMANCE OF SOLAR VORTEX ENGINE. [Final Year Project] (Submitted)

Yew , Kwang Liang (2010) Design Of A Steering Mechanism For A Personal Transporter. [Final Year Project] (Unpublished)

Yi, Kong Yien (2015) Effect of Back Rake Angle and Shape of PDC Cutter On Wear Rate In Hard Formation. [Final Year Project] (Unpublished)

Yong, Lawrence Hao Peng (2012) Fill Removal in Wellbore Using Coiled Tubing. [Final Year Project] (Unpublished)

Yong, Teck Kiong (2010) Mechanical Properties of Filament Wound Composite Pipe for Well Completion Pup Joint Application. [Final Year Project] (Unpublished)

Yong , Calvin Yee Zhun (2014) Laboratory Drill Rig Design for Bit Wear & Vibration Study. [Final Year Project] (Unpublished)

You, Hor Jun (2015) Synthesis and Characterization of Novel Glyceline-based Low Transition Temperature Mixtures (LTTM) with L-Arginine. [Final Year Project] (Unpublished)

Yousof Kunju, Mohammad Fadzil (2016) Nitriding of A316 Stainless Steel Pipe with Improvement of Corrosion Resistance. [Final Year Project] (Submitted)

Yunos, Muhammad Faqrurazi (2014) Computational Fluid Dynamic (CFD) of Drying Process of Sewage Sludge. [Final Year Project] (Unpublished)

Yusa’, Nur Atikah (2020) Analysis on Mechanical Properties of Waste High Density Polyethylene (HDPE) Plastic. [Final Year Project] (Submitted)

Yusni, Alif Aiman (2016) Heat Transfer Study of Helically Coiled Tube Heat Exchanger. [Final Year Project]

Yusof, Muhammad Shafiq (2012) Physical Properties Characterization of Biomass Fuel Briquette Made from Oil Palm Mill Residues. [Final Year Project] (Unpublished)

Yusoff, Muhamad Azlan (2012) Development of Life Cycle Cost Model of Passenger Car. [Final Year Project] (Unpublished)

Yusoff, Muhd. Aizat Nazmi (2009) The Influence ofTemperature on Mechanical Properties and Fiber Damage. [Final Year Project] (Unpublished)

Z

ZAHARI, MOHD ZULFADZLI (2011) THE EFFECT OF NITRIDING A MARTENSITIC STAINLESS STEEL WITH RESPECT TO TEMPERATURE VARIATION. [Final Year Project] (Unpublished)

ZAHARIN, HAIZUM AIMI (2019) ANALYSIS OF POROUS STRUCTURE DESIGNS FOR IMPLANT APPLICATION USING ADDITIVE MANUFACTURING. Masters thesis, Universiti Teknologi PETRONAS.

ZAHED, MOHD HAIDAR (2017) Experimental Investigation of Contact and Bending Stresses of Involute Gear Pair. [Final Year Project] (Submitted)

ZAHIDAH, KHAIRINA AZMI (2018) Development of Sodium Diethyldithiocarbamate-loaded Halloysite Nanotube in Epoxy as A Smart Anticorrosion Coating. Masters thesis, Universiti Teknologi PETRONAS.

ZAIDI, NURULJANNAH (2017) DEVELOPMENT OF HONEYCOMB CORE FROM NATURAL AND TROPICAL WOOD FIBER FOR STRUCTURAL APPLICATION. [Final Year Project]

ZAIN EL BYTTEE, SABRINA (2021) CFD SIMULATION OF GAS SEPARATION IN DIVERGING T-JUNCTION. [Final Year Project] (Submitted)

ZAINAL, HASNIZA (2009) EFFECT OF OIL PALM FIBER REINFORCEMENT ON MECHANICAL PROPERTIES OF POLYSTYRENE. [Final Year Project] (Unpublished)

ZAINAL, MUHAMMAD HAZIQ (2015) EVALUATION OF THE IMPACT OF OPERATING TEMPERATURE TO CORROSION RATE FOR (CUI). [Final Year Project] (Unpublished)

ZAINAL, ZA’IM AZWAN (2013) PERFORMANCE STUDY OF THE SOLAR-POWERED ABSORPTIVE REFRIGERATION PROCESS. [Final Year Project] (Unpublished)

ZAINAL ABIDIN, EZRANN ZHARIF (2013) INVESTIGATION OF STARTING BEHAVIOUR OF A FREE PISTON LINEAR GENERATOR ENGINE. Masters thesis, UTP.

ZAINUDDIN, AHMAD FAZUAN (2012) THERMAL ANALYSIS OF ELECTRICAL DISCHARGE MACHINING USING QUITE ELEMENT TECHNIQUE. [Final Year Project] (Unpublished)

ZAKARIA, MOHAMAD SYAMIM (2017) EFFECT OF RUDDER DESIGN ON HYDRODYNAMIC FORCES OF AUTONOMOUS UNDERWATER GLIDER. [Final Year Project]

ZAKARIA, MOHD SAFUAN (2017) SMALL SCALE PILOT PLANT THERMAL DRYER FOR DOMESTIC WASTEWATER SLUDGE DRYING SYSTEM. Masters thesis, Universiti Teknologi PETRONAS.

ZAKARIA MAHAMAT, AL TIDJANI (2012) SYNTHESIZING AND EVALUATION OF NEW COPPER-TUNGSTEN BASED EDM ELECTRODE FOR MACHINING HARDENED MATERIALS. PhD. thesis, Universiti Teknologi PETRONAS.

ZAMANI, MUHAMMAD ALDRIN SYAFRIZAL (2020) SIMULATION OF SAND PARTICLE FLOW THROUGH SAND SCREEN IN OIL WELL. [Final Year Project] (Submitted)

ZAMRI, MOHAMAD FAIZ (2017) FABRICATION OF AUTOMOBILE COMPOSITE SHELL STRUCTURE USING COMPRESSION MOLDING PROCESS. [Final Year Project]

ZARAWI, ZULFADHLI (2013) Investigation of Malaysian Parang Manufacturing Quality Variation with respect to Chemical, Mechanical and Physical Properties. [Final Year Project] (Unpublished)

ZEWGE, MESFIN GIZAW (2013) STEP COMPLIANT APPROACH FOR TURN-MILL OPERATIONS. PhD. thesis, Universiti Teknologi PETRONAS.

ZOHARI, ZAIFUL IQMAL (2012) A STUDY OF GASEOUS PRODUCTS OF MINERAL BASED INTUMESCENT FIRE RETARDANT COATING IN STRUCTURAL APPLICATION. [Final Year Project] (Unpublished)

ZULKIFL Y, ZULHASRlL (2010) Characterization of Thermal and Mechanical Properties of Polypropylene/Polycarbonate/PP-g-MA Blends. [Final Year Project] (Unpublished)

ZULKIFLE, MUHAMMAD AL-AMIN (2021) Failure Prediction in Laminated Fiber Reinforced Composite. [Final Year Project] (Submitted)

ZULKIFLI, MUHAMMAD AFIQ IKHWAN (2020) Numerical Evaluation of Thermal Striping in MLNG Tiga Regenerative Piping. [Final Year Project] (Submitted)

ZULKURNAIN, EZA SYAHERA (2017) Effects of Nano-sized Boron Nitride on Thermal Decomposition Behaviour of Epoxy-based Intumescent Coating. Masters thesis, Universiti Teknologi PETRONAS.

Zafar, Muhammad Adeel (2016) Material Flow Behavior and Mechanical Properties of Friction Stir Welded 16MM-Thick Nylon-6 Plates. Masters thesis, Universiti Teknologi PETRONAS.

Zahari, Mohamad Armiya (2011) Estimation of Burst Pressure of Corroded Pipeline Using Finite Element Analysis (FEA). [Final Year Project] (Unpublished)

Zainal, Ahmad Muhaimin bin (2009) Effective Mechanical Seal for Pump Applications at Onshore Gas Terminal. [Final Year Project] (Unpublished)

Zainal, Mohd Hafiz (2003) Development of an Automated Guided Vehicle (AGV). [Final Year Project] (Unpublished)

Zainal Abidin, Mohd Zul Akmal (2011) Design of Modular Fixture for CNC Machining Center. [Final Year Project] (Unpublished)

Zainal Abidin, Muhammad Anas Bin (2009) Hydrogen Production via Ice Electrolysis. [Final Year Project] (Unpublished)

Zainal Alam, Zainol Arifin (2011) A Study of Tensile Behavior on Drilling Induced Damage of Hybrid Composite. [Final Year Project] (Unpublished)

Zainalabidin, Muhammad Aizuddin (2008) MISCIBLE C02 INJECTION: SENSITIVITY TO FLUID PROPERTIES TINGGI FIELD. [Final Year Project] (Unpublished)

Zainalabidin, Muhammad Amirul Luthfi (2016) Effect of Agitated Turbulence on Demulsification of Crude Oil Emulsions in Production Separator. [Final Year Project] (Submitted)

Zainalabidin, Muhammad Arief Fikry (2014) Waxy Crude Oil Demulsification Study. [Final Year Project] (Unpublished)

Zaini, Suraya Nabilah (2014) Development of Spread sheet Based Simulation Model for Failure Prediction of Repairable System. [Final Year Project] (Unpublished)

Zaino!, Nur Syuhada (2011) Effeds of Coupling Agent on Mechanical Properties of Rice Husk Filled Polyethylene Composite. [Final Year Project] (Unpublished)

Zainol Rashid B. Hj. Osman, Zainol Rashid (2009) Design and Development of in-motion Inflator. [Final Year Project] (Unpublished)

Zainon, Ahmad Khairudin (2004) Development of a Subsonic Wind Tunnel in UTP - Selection of the Flow Visualization Device. [Final Year Project] (Unpublished)

Zainuddin, Abu Yazid (2011) Study ou wear resistance and microstructure of nanosilica-iron based composites. [Final Year Project] (Unpublished)

Zainuddin, Afiq Azreen (2011) Study of Combustion Characteristic of LPG with Steam in a Burner. [Final Year Project] (Unpublished)

Zainuddin, Mohamed Zakiran (2013) Optimal Design of Wheelchair Drive Mechanism. [Final Year Project] (Unpublished)

Zainuddin, Mohd Zulhilmi (2011) Design and Fabrication of Simple Vehicle Body Panel. [Final Year Project] (Unpublished)

Zainuddin, Zainor Faisal (2011) THE DESIGN OF THE DRIVE SYSTEM FOR A PERSONAL TRANSPORTER. [Final Year Project] (Unpublished)

Zainudin, Abdullah Farhan (2012) Influence of Heat Treatment and Microstructure on the Corrosion Performance of Carbon Steel Line Pipe in CO2 Environment. [Final Year Project] (Unpublished)

Zainudin, Muhammad Afif (2013) IMPROVING OF MANUFACTURING PRODUCTIVITY THROUGH SIMULATION. [Final Year Project] (Unpublished)

Zainudin, Muhammad Hazwan (2013) STUDY OF THERMALLY DRIVEN SORPTION CHILLER. [Final Year Project] (Unpublished)

Zainur, Muhammad Zakri (2017) Study on Compressibility of Gelled Waxy Crude Oil in Production Pipeline in Relation to Restart Flow. [Final Year Project]

Zakaria, Ariff Ezwan (2008) Sintering Carbon Nanotubes Reinforced Copper Powder Using Different Particle. [Final Year Project] (Unpublished)

Zakaria, Mohd Faiz Farhan (2021) Finite Element Analysis of Hybrid Composite Plate through Tensile Test. [Final Year Project] (Submitted)

Zakaria, Mohd Zakwan (2016) Enhancement Of Strength And Fire Resistance Properties Of Intumescent Coatings By Basalt Fibre. [Final Year Project] (Submitted)

Zakaria, Nur Aisah (2011) A Systematic Study of Film Formation in C02 Corrosion. [Final Year Project] (Unpublished)

Zakaria Bin Mohamed, Zakaria (2009) Effect of Chloride on Offshore Structure Welding Procedure. [Final Year Project] (Unpublished)

Zaley, Mohammad Yusof (2013) Mechanical Properties Study of Recycled Machinable Wax. [Final Year Project] (Unpublished)

Zamberi, Mohd Zaim Zarin (2021) Investigation of Solar Refrigeration System with Ground Based Cold Thermal Energy Storage for Tropical Countries. [Final Year Project] (Submitted)

Zammeri, Mohammad Farhan (2013) Experimental Characterization of the Absorptivity of Various Ground Materials for Solar Chimney Application. [Final Year Project] (Unpublished)

Zamri, Muhammad Syakir (2022) Evaluation of Salt Contaminations on Rust Stabilizing Formation. [Final Year Project] (Submitted)

Zamri, Ahmad Fairus (2008) Analysis of Jet Fire on IntumescentCoating Applied on SteelSubstrate. [Final Year Project] (Unpublished)

Zamri, Shafwan Akmal (2014) Dissertation Report of Slip-On Sprocket. [Final Year Project] (Unpublished)

Zarizambri Bin Ahmad, Zarizambri (2008) Design and Analysis of a Pedal Box System for a small Race-car. [Final Year Project] (Unpublished)

Zawawi, Muhammad Helmi Zin (2016) Thermodynamic Modelling of Organic Rankine Cycle (ORC) for Waste Heat Recovery of a Gas Turbine Engine. [Final Year Project] (Submitted)

Zieerwan Zainal, Zieerwan (2010) Sand Erosion Inside Pipe Of Crude Oil With 90° Bend By Cfd. [Final Year Project] (Unpublished)

Zikri Fahmi Bin Zainon, Zikri Fahmi (2010) Effect Of Sintering Time On Physical And Mechanical Properties Of Carbon Nano-Tubes Reinforced Copper Composite. [Final Year Project] (Unpublished)

Zolkefli, Masmaliza (2010) An Investigation Into Abrasive Resistance of Aluminum 6063, Stainless Steel 316 And Mild Steel Using Taber Linear Abraser And Taber Rotary Abraser. [Final Year Project] (Unpublished)

Zukifli, Muhamad Nur (2015) Numerical Analysis of Hybrid Composite Piping for Oil and Gas Application. [Final Year Project] (Unpublished)

Zul Azri, Azril Danial (2016) Simulation Study Effect of Fine Particle on Choke Valve by Using Computational Fluid Dynamic (CFD). [Final Year Project] (Submitted)

Zul Hilmi bin Awang, Zul Hilmi (2008) Investigation The Tribological Properties of Fiber Composite Material Reinforced With Carbon Nano Tube(CNT). [Final Year Project] (Unpublished)

Zul Mahadzir Oyama bin Ahmad Oyama, Zul Mahadzir Oyama (2009) Replacing Self-Balancing System of Personal Transporter by Using Gyroscope. [Final Year Project] (Unpublished)

Zulfikri Gopinath, Muhammad Khairul Nizam (2011) Study On The Effect Of Nitriding Temperature Towards Wear Resistance Of Duplex Stainless Steel. [Final Year Project] (Unpublished)

Zulkafli, Muhammad Harith (2016) Investigation of Nanofluids Selection for Solar Thermal Collectors. [Final Year Project] (Submitted)

Zulkafli, Zuli Izwan Bin (2009) Design and Analysis of a Small, Lightweight and Single Cylinder Car Drive Train System for UTP Formula SAE Team (UTP-FSAE). [Final Year Project] (Unpublished)

Zulkarnain, Ahmad Fahim (2016) Optimize Build Orientation for 3D Printing to Minimize Build Time and Support Structure. [Final Year Project] (Submitted)

Zulkefli, Muhammad Aiman (2022) Evaluation and Testing of Exoskeleton to Assist in Pineapple Harvesting. [Final Year Project] (Submitted)

Zulkefli, Luqman Hakim (2014) Design and Construction of Smartball for Oil & Gas Pipeline Inspection. [Final Year Project] (Unpublished)

Zulkhafle, Zulaikha Hanis (2022) Mechanical Properties of Proppants Coated with Hybrid Nanostructure for Effective Hydraulic Fracturing. [Final Year Project] (Submitted)

Zulkifli, Mohammad Zulkhairi (2022) EDEM Simulation of Particles Path in a Vertical Cyclone Separator. [Final Year Project] (Submitted)

Zulkifli, Haikal Bin (2009) Failure Analysis on Steel Tubing for Water Injection Well. [Final Year Project] (Unpublished)

Zulkifli, Muhammad Zulfadli (2016) Dropped Object Protection Modelling for Subsea Equipment. [Final Year Project] (Submitted)

Zulkifli, Zurhazrin Azureen (2011) Reliability Analysis of Pressure Relief Valve. [Final Year Project] (Unpublished)

Zulkifly, Muhammad Amsyar (2012) MODAL ANALYSIS OF AN AIRCRAFT LANDING GEAR. [Final Year Project] (Unpublished)

Zulkipli, Muhammad Shamil (2016) Performance Study on Hot Air Recovery for Solar Thermoelectric Cooler System. [Final Year Project]

Zurhazrin Azureen Binti Zulkifli, Zurhazrin (2011) Reliability Analysis of Pressure Relief Valve. [Final Year Project] (Unpublished)

This list was generated on Thu Jun 20 10:27:27 2024 +08.